Chair Rail Moulding - Available in 1-2 Days

ID #	Image	Width x Thickness (inches)	Details
0063		1-3/8 x 5/8	Moulding 05/03..T-2 $50 set up
0544		1-1/2 x 3/4	symmetrical, beaded Moulding 35/05...T-56 $50 set up
0883		1-1/2 x 5/8	Symmetrical The notch was for an inlay piece of brass Moulding 55/14...T-85 $75 set up
1105		1-1/2 x 3/4	Symmetrical Moulding 73/12...T-13 $50 set up
1906		1-1/2 x 1-1/8	Moulding 134/12...T-179 $75 set up as shown $50 set up w/out dado on bottom
2055		1-1/2 x 1-1/16	Moulding 154/09...T-194 $50 set up
2064		1-1/2 x 3/4	Moulding 155/03...T-198 $50 set up
2110		1-1/2 x 7/8	Moulding 158/11...T-202 $75 set up
0236		1-9/16 x 1	Moulding 17/09...T-33 beads $50 set up
2058		1-5/8 x 3/8	Moulding 154/12...T-193 $60 set up
1385		1-11/16 x 3/4	Moulding 92/05...T-133 $50 set up
0062		1-3/4 x 3/4	Moulding 05/02...T-2 $50 set up an old Boren Mldg
0179		1-3/4 x 1	Moulding 10/10...T-14 $50 set up
0406		1-3/4 x 5/8	Moulding 27/17...T-31 $50 set up
0805		1-3/4 x 5/8	symmetrical Moulding 47/05...T- $50 set up
2117		1-3/4 x 1-1/4	Moulding 159/05...T-203 $50 set up
0529		1-13/16 x 13/16	Moulding 34/07...T-56 $50 set up
1511		1-13/16 x 1-5/8	Moulding 102/07...T-146 $75 set up
0598		1-7/8 x 3/4	Moulding 37/09 $50 set up
2043		1-15/16 x 3/4	Moulding 153/09...T-197 $50 set up
0029		2 x 1-1/2+	symmetrical, Beaded Moulding 01/10...T-19 $50 set up
0061		2 x 3/4	aka boren moulding 05/01...T-2 $50 set up
0176		2 x 3/4	Moulding 11/06...T-10 $50 set up PM-6 without the bottom knife
0380		2 x 1-1/2	Moulding 143/09...T-43 $50 set up
0435		2 x 9/16	Moulding 31/01...T-27 aka LSCR1 $50 set up
0454		2 x 3/4	aka LSCR3 Moulding 31/14...T-54 aka LSCR3 $50 set up
0476		2 x 1-1/16	Moulding 141/06...T-51 $50 set up
0688		2+ x 3/4	symmetrical Moulding 42/08...T-65 $75 set up....Add $.30/lf for running twice
0729		2 x 3/4	Moulding 48/08...T-75 $50 set up
1175		2 x 3/4	Symmetrical Moulding 77/07...T-123 $50 set up
1294		2 x 1	Moulding 85/14...T-119 $75 set up, $50 without dado
1479		2 x 5/8	Moulding 99/21...T-143 $50 set up
1497		2 x 5/8	Moulding 101/07...T-145 $50 set up
1531		2 x 3/4	Moulding 104/04...T-148 $50 set up
1594		2 x 1	Moulding 109/07...T-153 $50 set up
2081		2 x 3/4	Moulding 156/08...T-198 $50 set up
0189		2-1/8 x 1-1/4	Moulding 14/05...T-16 $50 set up
0255		2-1/8 x 1-1/4	Moulding 150/10 $50 set up
0376		2-1/8 x 1	Moulding 26/03...T-36 $50 set up
0705		2-1/8 x 3/4	Moulding 147/09...T-61 $50 set up
1360		2-1/8 x 3/4	Moulding 90/07...T-134 $50 set up
0503		2-3/16 x 3/4	Moulding 33/03...T-57 $75 set up
0292		2-1/4 x 11/16	Moulding 148/04...T-25 $50 set up
0504		2-1/4 x 3/4	symmetrical Moulding 33/04...T-49 $75 set up
0727		2-1/4 x 7/8	Moulding 48/06...T-74 $50 set up
0804		2-1/4 x 5/8	this can have a rope inserted in the groove Moulding 47/04...T-70 $50 set up
1341		2-1/4 x 3/4	Moulding 88/11...T-133 $75 set up with dado please spec dado size
1499		2-1/4 x 1-1/4	Moulding 101/09...T-144 $60 set up
1507		2-1/4 x 2-1/8	Moulding 102/03...T-143 $50 set up
1568		2-1/4 x 1-1/16	Moulding 107/05...T-152 $60 set up
1716		2-1/4 x 5/8	Moulding 118/11...T-164 $60 set up Symmetrical
1840		2-1/4 x 3/4	Moulding 129/10...T-179 $50 set up
1878		2-1/4 x 1-1/16	Moulding 132/12...T-184 $50 set up
2023		2-1/4 x 3/4	Moulding 151/11...T-196 $75 set up
0560		2-3/8 x 13/16	Moulding 35/14...T-50 Beaded $50 set up
1567		2-3/8 x 1-3/16	Moulding 107/04...T-151 $50 set up
1575		2-3/8 x 1-1/4	Moulding 107/12...T-152 $75 set up with cutout shown, $50 w/out cutout
1920		2-3/8 x 7/8	Moulding 135/09...T-178 $50 set up
0065		2-1/2 x 3/4	Moulding 05/06...T-1 $75 set up specify dado dimensions
0067		2-1/2 x 3/4	symmetrical Moulding 05/08...T-1 $50 set up
0129		2-1/2 x 1-7/16	Moulding 10/09...T-14 $75 set up Note left side is slanted.
0144		2-1/2 x 1-1/8	symmetrical Moulding 12/10...T-44 $95 set up or $50 with no dados
0177		2-1/2 x 1-1/4	any chair rail can be made thicker and a notch put in to accept paneling or waincoat making it a panel cap like this one shown. Moulding 11/07...T-8 $75 set up
0184		2-1/2 x 7/8	Moulding 14/01...T-44 $50 set up
0221		2-1/2 x 1	Moulding 141/09...T-38 $75 set up
0287		2-1/2 x 3/4	Moulding 149/07...T-31 $75 set up beads, symmetrical
0290		2-1/2 x 13/16	Moulding 150/11...T-31 $50 set up
0397		2-1/2 x 13/16	Moulding 27/08...T-34 aka LSCR2 $50 set up
0484		2-1/2 x 1-1/4	Moulding 32/03...T-49 $75 set up
0575		2-1/2 x 1+	Moulding 36/06...T-50 $50 set up
0730		2-1/2 x 3/4	Moulding 48/09...T-77 $50 set up
0732		2-1/2 x 1-1/4	Moulding 48/11...T-76 $50 set up
0862		2-1/2 x 5/8	Symmetrical, beaded Moulding 54/04...T-82 $75 set up
0869		2-1/2 x 1-1/2	Moulding 54/11...T-81 $50 set up
1101		2-1/2 x 3/4	Moulding 73/08...T-98 symmetrical $75 set up, must run twice, add $.30
1143		2-1/2 x 3/4	Moulding 74/05...T-101 $50 set up
1145		2-1/2 x 5/8	Moulding 74/07...T-103 $50 set up, add $20 for relief
1147		2-1/2 x 3/4	Moulding 74/09...T-102 $60 set up
1173		2-1/2 x 1-1/2	Moulding 77/05...T-113 $50 set up
1174		2-1/2 x 13/16	Moulding 77/06...T-126 $75 set up
1200		2-1/2 x 11/16	Moulding 79/08...T-127 $50 set up
1219		2-1/2 x 1-3/16	Moulding 80/10...T-121 $50 set up
1353		2-1/2 x 1-1/4	Moulding 89/11...T-138 $85 set up
1362		2-1/2 x 3/4	Moulding 90/09...T-99 $75 set up, add .30 to run twice symmetrical
1759		2-1/2 x 5/8	Moulding 122/02...T-171 $60 set up Symmetrical
1794		2-1/2 x 3/4	Moulding 125/08...T-193 $50 set up
1870		2-1/2 x 1-1/16	Moulding 132/04...T-184 $50 set up
2041		2-1/2 x 1-1/2	Moulding 153/07...T-195 $50 set up
0034		2-5/8 x 1-1/8	can be made without dado Moulding 02/07...T-8 $75 set up
0374		2-5/8 x 1	Moulding 146/06...T-43 $60 set up
1014		2-5/8 x 5/8	Symmetrical, beads Moulding 65/10...T-95
1177		2-5/8 x 1-7/16	Moulding 77/09...T-124 $50 set up
1549		2-5/8 x 3/4	Moulding 105/10...T-15 $50 set up
1569		2-5/8 x 1-3/8	Moulding 107/06...T-151 $50 set up
1662		2-5/8 x 11/16	Moulding 114/12...T-159 $50 set up
2116		2-5/8 x 1-1/4	Moulding 159/04...T-13,202 $60 set up
0037		2-3/4 x 1-1/8	symmetrical, beads Moulding 02/04...T-3 $50 set up
0377		2-3/4 x 15/16	Moulding 26/04...T-30 $50 set up
0391		2-3/4 x 1	Moulding 27/01...T-34 $50 set up
1008		2-3/4 x 13/16	Moulding 65/04...T-93 $50 set up
1258		2-3/4 x 3/4	Symmetrical, beads Moulding 83/04...T-116 $50 set up
1288		2-3/4 x 5/8	Symmetrical, beads Moulding 85/08...T-119 $60 set up, add .30 to run twice
1340		2-3/4 x 1-1/4	Moulding 88/10...T-134 $50 set up
1608		2-3/4 x 15/16	Moulding 110/06...T-155 $75 set up
1740		2-3/4 x 3/4	Moulding 120/04...T-168 $75 set up
1750		2-3/4 x 1-3/8	Moulding 121/06...T-169 $75 set up symmetrical
1887		2-3/4 x 1-1/8	Moulding 133/05...T-179 $50 set up
1919		2-3/4 x 1-1/4	Moulding 135/08...T-173 $50 set up
2044		2-3/4 x 1-1/16	Moulding 153/10...T-197 $50 set up
0378		2-7/8 x 11/16	Moulding 26/05...T-36 $50 set up
0694		2-7/8 x 1-3/8+-	Moulding 43/01...T-62 $50 set up
1246		2-7/8 x 1/2	Moulding 82/11...T-114 this one was used as a cradle for a compound crown $50 set up
1672		2-7/8 x 1	Moulding 115/05...T-162 $50 set up
0527		2-15/16 x 1	Moulding 34/05...T-57 $50 set up
0284		3 x 3/4	Moulding 20/09...T-misc $75 set up add $20 for dado Symmetrical
0325		3 x 1	dado can be any size Moulding 142/08...T-29 $75 set up
0340		3 x 3/4	Dado can be any size. symmetrical Moulding 24/03...T-28 $75 set up
0356		3 x 13/16	symmetrical Moulding 25/02...T-36 $50 set up
0389		3 x 1-1/8	Moulding 146/04...T-40 $75 set up
0580		3 x 13/16	symmetrical Moulding 36/11...T-50 $85 set up
0603		3 x 1	Moulding 37/14...T-52 Three knife set-up...$95
0622		3 x 13/16	Moulding 144/10...T-60 $85 set up
0916		3+ x 3/4	Symmetrical Moulding 58/09...T-90 $75 set up, add .30 to run twice
1104		3 x 11/16	Moulding 73/11...T-97 $50 set up
1226		3 x 1-1/2	Moulding 81-05...T-122 Symmetrical $75 set up give dado dimensions
1227		3 x 1	Moulding 81/06...T-126 $75 set up dado can be any size or not at all
1286		3 x 13/16	Moulding 85/06...T-117 $50 set up
1287		3 x 3/4	Moulding 85/07...T-41 ...see 25/12 $75 set up with relief
1321		3 x 11/16	Moulding 87/08...T-142 $50 set up
1338		3 x 1	Moulding 88/08...T-131 $50 set up
1342		3 x 3/4	Moulding 88/12...T-138 $50 set up
1571		3 x 1-5/8	Moulding 107/08...T-152 $75 set up please spec dado if needed
1850		3 x 1	Moulding 130/06...T-181 $50 set up
1932		3 x 3/4	Moulding 136/07...T-175 $60 set up
2077		3 x 1	Moulding 156/04...T-199 $50 set up
0634		3-1/8 x 1-1/4+-	can be any thickness or width with the pattern running on both sides. symmetrical Moulding 39/10...T-58 $75 set up, add $.30/lf to run twice
0777		3-1/8 x 1/2	Moulding 45/04...T-72 $50 set up
1591		3-1/8 x 1-1/2	Moulding 109/04...T-153 $75 set up please spec dado size
0175		3-1/4 x 3/4	Moulding 11/05...T-12 $50 set up
0322		3-1/4 x 3/4	symmetrical Moulding 22/13...T-37 $75 set up
1566		3-1/4 x 1-1/2	Moulding 107/03...T-151 $50 set up
1572		3-1/4 x 1-1/4	Moulding 107/09...T-151 $50 set up
1763		3-1/4 x 1-5/8	Moulding 122/06...T-171 $75 with relief
0312		3-3/8 x 1-1/16	Moulding 22/04...T-37 $75 set up
0396		3-3/8 x 11/16	symmetrical Moulding 27/07...T-41 $60 set up
0676		3-3/8 x 7/8	Moulding 41/19...T-67 $50 set up
1296		3-3/8 x 1-7/16	Moulding 86/02...T-121. $75 set up
1496		3-3/8 x 1-3/16	Moulding 101/06...T-144 $50 set up
0025		3-1/2 x 1-1/4	aka CR-6 moulding 01/06...T-22 $75 set up
0060		3-1/2 x 3/4	symmetrical Moulding 04/09...T-21 $60 set up, ad .30 per foot to run twice.
0196		3-1/2 x 3/4	Moulding 15/02...T-23 $75 set up
0417		3-1/2 x 3/4	symmetrical, two flutes Moulding 29/03...T-51 $60 set up
0424		3-1/2 x 2	Moulding 28/09...T-20 $75 set up
0590		3-1/2 x 1-1/4	Moulding 37/01... T-50 $50 set up
0797		3-1/2 x 3/4	symmetrical Moulding 46/10...T-71 $50 set up
1097		3-1/2 x 1-5/8	Symmetrical Moulding 73/04...T-100 $50 set up
1099		3-1/2 x 11/16	Moulding 73/06...T-99 $50 set up
1102		3-1/2 x 3/4	Symmetrical Moulding 73/09...T-99 $50 set up
1172		3-1/2 x 1	Moulding 77/04...T-126 $50 set up
1225		3-1/2 x 1	Symmetrical Moulding 81/04...T-113 $50 set up
1228		3-1/2 x 3/4	Symmetrical Moulding 81/07...T-112 $50 set up add .30 for second pass
1276		3-1/2 x 1-1/4	Moulding 84/07...T-118 $50 set up
1278		3-1/2 x 1-1/2	Symmetrical Moulding 84/09...T-117 $50 set up
1283		3-1/2 x 2-1/4	Moulding 85/03...T-119 $75 set up give dado dimensions
1306		3-1/2 x 3/4	Moulding 86/12...T-misc used as a wainscoat cap $95 set up
1337		3-1/2 x 1	Moulding 88/07...T-141 $50 set up without relief
1345		3-1/2 x 1-1/8	Moulding 89/03...T-141 $50 set up Similar to C196
1346		3-1/2 x 1-1/4	Moulding 89/04...T-140 $60 set up
1685		3-1/2 x 1-3/8	Moulding 116/07...T-163 $50 set up
1708		3-1/2 x 3/4	Moulding 118/03...T-165 $50 set up
1715		3-1/2 x 11/16	Moulding 118/10...T-164 $75 set up
1803		3-1/2 x 1-1/4	Moulding 126/07...T-189 $75 set up
1890		3-1/2 x 3/4	Moulding 133/08...T-18 $60 set up fluted symmetrical
1891		3-1/2 x 3/4	Moulding 133/08...T-18 $60 set up fluted symmetrical
1892		3-1/2 x 3/4	Moulding 133/09...T-180 $60 set up fluted symmetrical
1946		3-1/2 x 7/8	Moulding 137/02...T-173 $50 set up
1966		3-1/2 x 3/4	Moulding 138/04...T-192 %0 set up symmetrical
0232		3-5/8 x 3/4	symmetrical Moulding 17/07...T-33 $50 set up
1095		3-5/8 x 1	Symmetrical Moulding 73/02...T-99 $50 set up
1096		3-5/8 x 3/4	Moulding 73/03...T-103 $50 set up, add $20 for relief
1348		3-5/8 x 1-1/4	Moulding 89/06...T-134 $60 set up
1354		3-5/8 x 1-1/8	Moulding 90/01...T-137 $60 set up
1556		3-5/8 x 7/8	Moulding 106/04...T-150 $50 set up
1918		3-5/8 x 1	Moulding 135/07...T-175 $50 set up
0338		3-3/4 x 1-1/16	Moulding 24/02...T-32 $75 set up
0414		3-3/4 x 5/8	symmetrical Moulding 29/02...T-27 $50 set up
0591		3-3/4 x 1-3/8	Moulding 37/02...T-50 $50 set up
0820		3-3/4 x 5/8	Moulding 51/07...T-83 $75 set up
0855		3-3/4 x 13/16	Moulding 53/12...T-84 $75 set up $50 without relief in back.
0648		3-7/8 x 1	Moulding 40/01...T-62 $50 set up
1098		3-7/8 x 1-3/4	Moulding 73/05...T-101 $50 set up
1298		3-7/8 x 1-1/16	Moulding 86/04...T-121 $50 set up
0047		4 x 1	symmetrical Moulding 142/07...T-13 $95 set up
0100		4 x 1	goes with [BBRDM0102] symmetrical Moulding 08/04...T-3 $95 set up add $20 for the relief
0248		4 x 1-1/8	Moulding 149/03...T-33 $75 set up
0657		4 x 1-1/4+-	panel cap or wainscoating cap or just chair rail. It is actually a modified CR-6 Moulding 40/10...T-61 $75 set up as shown
0687		4 x 3/4	symmetrical, beads Moulding 42/07...T-63 $75 set up
0847		4 x 1	could be a panel cap Moulding 53/04...T-78 $75 set up
1197		4 x 3/4	Symmetrical, beads Moulding 79/05...T-116 $50 set up
1529		4 x 3/4	Moulding 104/02...T-148 $60 set up, add.30/lf for running twice symmetrical
1799		4 x 2	Moulding 126/03...T-183 $50 set up
1800		4 x 1-1/4	Moulding 126/04...T-182 $75 set up
1804		4 x 5/8	Moulding 126/08...T-192 $50 set up symmetrical
1871		4 x 1-7/8	Moulding 132/05...T-190 $50 set up
1888		4 x 1-3/8	Moulding 133/06...T-180 $50 set up
1899		4 x 3/4	Moulding 134/05...T-188 $75 set up symmetrical
1922		4 x 3/4	Moulding 135/11...T-172 $75 set up Symmetrical
0633		4-1/8 x 3/4	symmetrical Moulding 39/09...T-58 $50 set up
1300		4-1/4 x 3/4	Moulding 86/06...T-118 $50 set up. add $20 for relief
1333		4-1/4 x 2	Moulding 88/03...T-132 $60 set up
1762		4-1/4 x 1-3/4	Moulding 122/05...T-171 $75 set up
2065		4-1/4 x 1-1/4	Moulding 155/04...T-195 $50 set up
1094		4-3/8 x 1	Symmetrical Moulding 73/01...T-101 $50 set up
0126		4-1/2 x 3/8	symmetrical Moulding 08/12...T-16 $95 set up
1103		4-1/2 x 3/4	Moulding 73/10...T-105 $75 set up
1702		4-1/2 x 13/16	Moulding 117/08...T-164 $60 set up Symmetrical
1858		4-1/2 x 1-1/4	Moulding 130/14...T-182 $50 set up
1525		4-7/8 x 1	Moulding 103/07...T-148 $50 set up
1100		5 x 3/4	Moulding 73/07...T-102 $50 set up symmetrical
1573		5 x 11/16	Moulding 107/10...T-152 $60 set up, add .30/lf to run twice symmetrical
1508		5-1/8 x 1-9/16	Moulding 102/04...T-115
1334		5-3/16 x 1-1/16	Moulding 88/04...T-142 $60 set up
1332		5-1/2 x 1-1/4	Moulding 88/02...T-136 $50 set up
1900		5-7/8 x 1-3/4	Moulding 134/06...T-177 $50 set up

Need More Chair Rail Moulding Options?

View in-stock mouldings in this category: In-Stock Chair Rail Moulding.

Didn't Find What You Were Looking For?

Our on-site millwork shop is ready to cut to your specifications. Turn around is 1-2 days. Contact us online or call us at (713) 686-6176.

Search Moulding Again?

Return to wood moulding home.

713-686-3217 FAX	713-686-6176 DIRECT	1-800-606-6176
CLOSED SUNDAY	Monday - Friday, 7:30 AM - 5 PM	Saturday 8:30AM -NOON
MAP & DIRECTIONS	COMMENTS & FEEDBACK	PRIVACY POLICY
	2015 Houston Hardwoods. All Rights reserved.
Houston Hardwoods Company is located in Houston, Texas. We offer the largest selection of mouldings in Texas. Marine grade plywood is our specialty. Every day, we are providing a better selection of softwoods, hardwoods, exotic wood, plywood, MDF and melamine, edgebanding and veneer sheeting. We have been in business for more than two decades, and the organization still starts every day with the partners who got it started!

Chair Rail Moulding - Available in 1-2 Days

Need More Chair Rail Moulding Options?

Didn't Find What You Were Looking For?

Search Moulding Again?

Search On Product Code