| ID # |
Image |
Width x Thickness (inches) |
Details |
| 0096 |  | 3/8 x 3/8 | Moulding 08/02...T-29
Very small for our moulder, difficult to run; 50' in, 30' out. random length orders only extra set up...$80 Type: cvbdm |
| 0127 |  | 3/8 x 3/8 | Moulding 10/07...T-4
small mouldings are more time consuming so quote a $75 set up. Do not promise particular lengths...only total footages because it is fragile and we don't want to trash a whole pc. because it breaks off 6 inches from one end. Type: cvbdm |
| 0660 |  | 1/2 x 5/16 | Moulding 40/13...T-59
$50 set up Type: miscm |
| 1263 |  | 1/2 x 1/2 | Moulding 83/09...T-114
$50 set up Type: doorm |
| 1903 |  | 1/2 x 3/8 | Moulding 134/09...T-
$50 set up Type: doorm |
| 1137 |  | 9/16 x 1/2 | Moulding 76/23...T-105
$50 set up Type: crndm |
| 2053 |  | 9/16 x 1/4 | Moulding 154/07...T-193
$70 set up Type: doorm |
| 2069 |  | 9/16 x 1/2 | Moulding 155/08...T-199
$50 set up Type: crwnm |
| 0109 |  | 5/8 x 5/8 | aka 5/8" qtr round
Moulding 09/09...T-13
$50 set up Type: crndm |
| 0659 |  | 5/8 x 3/8 | Moulding 40/12...T-59
$50 set up Type: miscm |
| 0667 |  | 5/8 x 3/8 | Moulding 41/10...T-
$50 set up Type: doorm |
| 0841 |  | 5/8 x 5/8 | Moulding 52/12...T-
typical glass stop see moulding CVBDM0096 for basic shape
$50 set up Type: cvbdm |
| 0975 |  | 5/8 x 1/4 | Moulding 62/11...T-85
$60 set up Type: doorm |
| 1134 |  | 5/8 x 9/16 | Moulding 76/20...T-110
$50 set up Type: doorm |
| 1136 |  | 5/8 x 5/8 | Moulding 76/22...T-109
$50 set up Type: cvbdm |
| 1138 |  | 5/8 x 3/8 | Moulding 76/24...T-105
$50 set up Type: crndm |
| 1852 |  | 5/8 x 1/2 | Moulding 130/08...T-
$50 set up Type: doorm |
| 0200 |  | 11/16 x 11/16 | Moulding 15/04...T-11
$50 set up Type: miscm |
| 0330 |  | 11/16 x 5/16 | Moulding 145/07...T-29
$50 set up Type: doorm |
| 1322 |  | 11/16 x 1/2 | Moulding 87/09...T-82 (Glass Bead) Type: doorm |
| 1599 |  | 11/16 x 5/16 | Moulding 109/12...T-153
$50 set up Type: doorm |
| 0052 |  | 3/4 x 3/4 | symmetrical
Moulding 04/01...T-15
$75 set up Type: crndm |
| 0110 |  | 3/4 x 3/8 | aka clover, discontinued as s t o c k item.
symmetrical
Moulding 09/10...T-10
$50 set up Type: crndm |
| 0186 |  | 3/4 x 5/16 | Moulding 14/03...T-16
$50 set up Type: crndm |
| 0439 |  | 3/4 x 3/8 | Moulding 31/03...T-27
$75 set up Type: cbntm |
| 0444 |  | 3/4 x 1/2 | Moulding 31/06...T-17
$60 set up
AKA: CM3, CM-3 Type: cbntm |
| 0446 |  | 3/4 x 3/4 | Three beaded cove
Moulding 31/08...T-54
aka three-bead cove
$50 set up Type: crndm |
| 0468 |  | 3/4 x 3/8 | Moulding 144/06...T-41
$50 set up Type: doorm |
| 0585 |  | 3/4 x 5/16 | Moulding 143/07...T-27
bead
$60 set up
Susan Fruit Type: cbntm |
| 0588 |  | 3/4 x 1/2 | Moulding 148/03...T-56
$50 set up Type: doorm |
| 0589 |  | 3/4 x 1/4 | Moulding 148/11...T-53
$50 set up Type: miscm |
| 0602 |  | 3/4 x 3/4 | Moulding 37/13...T-15
$60 set up Type: cvbdm |
| 0658 |  | 3/4 x 7/16 | Moulding 40/11...T-
$50 set up Type: miscm |
| 0672 |  | 3/4 x 3/4 | Moulding 41/15...T-64
$60 set up Type: crndm |
| 0673 |  | 3/4 x 1/2 | Moulding 41/16...T-
$60 set up Type: crndm |
| 0723 |  | 3/4 x 1/2 | Moulding 48/02...T-17
$50 set up Type: doorm |
| 0800 |  | 3/4 x 3/8 | Moulding 46/13...T-
$50 set up Type: doorm |
| 0829 |  | 3/4 x 5/8 | Moulding 51/16...T-72
$50 set up Type: doorm |
| 1022 |  | 3/4 x 9/16 | Moulding 40/14...T-50
$75 set up Type: custo |
| 0990 |  | 3/4 x 1/2 | glass stop or glass bead
Moulding 63/13...T-94
specifically for Door Pro
$50 set up Type: miscm |
| 1017 |  | 3/4 x 1/2 | glass bead
Moulding 65/13...T-78
$50 set up Type: doorm |
| 1124 |  | 3/4 x 5/8 | Moulding 76/10...T-98
$50 set up Type: doorm |
| 1133 |  | 3/4 x 3/4 | Moulding 76/19...T-55
$50 set up Type: doorm |
| 1135 |  | 3/4 x 5/8 | Moulding 76/21...T-105
$60 set up Type: cvbdm |
| 1202 |  | 3/4 x 3/4 | Moulding 79/10...T-127
$50 set up Type: doorm |
| 1251 |  | 3/4 x 1/2 | Moulding 82/16...T-114
$75 set up Type: panlm |
| 1318 |  | 3/4 x 1/4 | Moulding 87/05...T- (3-Bead Screen) Type: doorm |
| 1320 |  | 3/4 x 3/4 | Moulding 87/07...T-85
$50 set up Type: doorm |
| 1398 |  | 3/4 x 1/2 | Moulding 92/18...T-114
$50 set up Type: doorm |
| 1455 |  | 3/4 x 5/8 | Moulding 98/10...T-82
$50 set up Type: doorm |
| 1465 |  | 3/4 x 3/4 | Moulding 99/08...T-115
$95 set up Type: miscm |
| 1472 |  | 3/4 x 5/8 | Moulding 99/15...T-138
$75 set up Type: panlm |
| 1474 |  | 3/4 x 3/4 | Moulding 99/17...T-15
$60 set up Type: miscm |
| 1514 |  | 3/4 x 3/8 | Moulding 102/10...T-145
$60 set up Type: miscm |
| 1532 |  | 3/4 x 9/16 | Moulding 104/05...T-147
$50 set up Type: doorm |
| 1655 |  | 3/4 x 5/8 | Moulding 114/05...T-156
$50 set up Type: doorm |
| 1657 |  | 3/4 x 1/4 | Moulding 114/07...T-158
$50 set up Type: miscm |
| 1701 |  | 3/4 x 9/16 | Moulding 117/07...T-
$95 set up
1/2" offset Type: cbntm |
| 1889 |  | 3/4 x 7/16 | Moulding 133/07...T-27
$50 set up Type: doorm |
| 1904 |  | 3/4 x 1/2 | Moulding 134/10...T-186
$50 set up Type: doorm |
| 0331 |  | 13/16 x 3/4 | Moulding 23/02...T-29
$50 set up Type: doorm |
| 1312 |  | 13/16 x 3/4 | Moulding 86/14...T-140
$85 set up
used for cabinet doors, with a finger pull Type: cbntm |
| 1478 |  | 13/16 x 3/4 | Moulding 99/20...T-143
$50 set up Type: doorm |
| 1635 |  | 13/16 x 1/2 | Moulding 112/07...T-157
$50 set up Type: doorm |
| 1659 |  | 13/16 x 1/4 | Moulding 114/09...T-
$50 set up Type: miscm |
| 1806 |  | 13/16 x 13/16 | Moulding 126/10...T-193
$75 set up Type: cbntm |
| 2019 |  | 13/16 x 3/4 | Moulding 151/07...T-176
$50 set up Type: doorm |
| 0172 |  | 7/8 x 3/4 | yes, it is irregular
Moulding 11/02...T-12
$50 set up Type: crndm |
| 0237 |  | 7/8 x 9/16 | Moulding 17/10...T-33
$50 set up Type: doorm |
| 0445 |  | 7/8 x 3/4 | full cornered crown
Moulding 31/07...T-51
$50 set up Type: crwnm |
| 0448 |  | 7/8 x 5/16 | tall, narrow shoe mold
Moulding 30/01...T-49
$60 set up Type: cbntm |
| 0669 |  | 7/8 x 3/4 | Moulding 41/12...T-62
$75 set up Type: cbntm |
| 0842 |  | 7/8 x 9/16 | Moulding 52/13...T-79
$50 set up
Type: doorm |
| 0858 |  | 7/8 x 11/16 | this was used at the bottom of upper cabinets as a light valenceMoulding 53/15...T-78
$50 set up
susan fruit Type: doorm |
| 0949 |  | 7/8 x 3/4 | dado can be spec'd
Moulding 60/16...T-93
$75 set up, dado any size Type: panlm |
| 0974 |  | 7/8 x 1/2 | Moulding 62/10...T-89
$50 set up Type: doorm |
| 0989 |  | 7/8 x 11/16 | glass stop or glass bead
Moulding 63/12...T-94
specifically for Door Pro
$95 set up Type: miscm |
| 1305 |  | 7/8 x 13/16 | Moulding 86/11...T-117
$50 set up Type: doorm |
| 1392 |  | 7/8 x 5/8 | Moulding 92/12...T-128
$50 set up Type: doorm |
| 1399 |  | 7/8 x 3/4 | Moulding 92/19...T-134
$50 set up Type: doorm |
| 1613 |  | 7/8 x 9/16 | Moulding 110/11...T-155
$75 set up
you may spec dado size Type: panlm |
| 1656 |  | 7/8 x 1/2 | Moulding 114/06...T-162
%0 set up
Type: miscm |
| 1872 |  | 7/8 x 3/8 | Moulding 132/06...T-
$50 set up
glass bead
Type: doorm |
| 1311 |  | 15/16 x 3/4 | Moulding 86/13...T-137
$50 set up Type: panlm |
| 1826 |  | 15/16 x 5/8 | Moulding 128/07...T-
$50 set up Type: doorm |
| 1931 |  | 15/16 x 5/8 | Moulding 136/06...T-173
$60 set up Type: doorm |
| 0023 |  | 1 x 3/4 | Moulding 01/04...T-11
$50 set up Type: doorm |
| 0039 |  | 1 x 1/4 | fancy screen with 5 beads. Beaded, symmetrical
Moulding 02/02...T-5
$50 set up Type: doorm |
| 0092 |  | 1 x 3/4 | glass stop used to mount 1/4" glass into a 1-3/4" door
Moulding 06/11...T-
$75 set up Type: doorm |
| 0108 |  | 1 x 3/4 | Moulding 09/08...T-10
$50 set up Type: crndm |
| 0142 |  | 1 x 1 | aka 1" full round
Moulding 12/08...T-13
We have 1-1/4", 1-1/2", 1-5/8", 1-3/4", 2" diameter full rounds also.
all full rounds are $120 set ups. Type: crndm |
| 0148 |  | 1 x 13/16 | custom lip mold
Moulding 13/02...T-4
$75 set up Type: cbntm |
| 0227 |  | 1 x 1/2 | used as a tall shoe mold
Moulding 17/04...T-42
$50 set-up
Type: bbrdm |
| 0257 |  | 1 x 5/8 | just another custom shoe mold
Moulding 19/02...T-40
$50 set-up Type: bbrdm |
| 0258 |  | 1 x 3/4 | Moulding 19/03...T-40
$60 set up Type: doorm |
| 0280 |  | 1 x 1 | 1/4" tab fits into dado around deck/table surfaces
Moulding 19/19...T-13
Symmetrical
$95 set up Type: crndm |
| 0318 |  | 1 x 3/8 | Moulding 22/10...T-37
$50 set up Type: doorm |
| 0332 |  | 1 x 3/4 | custom lip
Moulding 23/03...T-28
$75 set up Type: cbntm |
| 0395 |  | 1 x 3/8 | Moulding 27/06...T-34
$50 set up Type: doorm |
| 0499 |  | 1 x 1-1/8 | a fruit under cabinet mldg
Moulding 148/05...T-57
$60 set up Type: crndm |
| 0522 |  | 1 x 9/16 | Moulding 148/12...T-57
$50 set up
susan fruit Type: doorm |
| 0543 |  | 1 x 13/16 | Moulding 35/04...T-56
$75 set up Type: doorm |
| 0568 |  | 1 x 5/8 | Moulding 148/13...T-53
$75 set up Type: miscm |
| 0620 |  | 1 x 5/8 | Moulding 142/05...T-60
$50 set up Type: doorm |
| 0621 |  | 1 x 13/16 | Moulding 150/02...T-60
$75 set up Type: panlm |
| 0885 |  | 1 x 3/8 | not a half round, symmetrical
Moulding 55/16...T-20
$50 set up Type: crndm |
| 0933 |  | 1 x 1/2 | Moulding 59/13...T-69
$50 set up Type: doorm |
| 0945 |  | 1 x 15/16 | Moulding 60/12...T-93
Symmetrical
$50 set up Type: miscm |
| 0950 |  | 1 x 9/16 | Moulding 60/17...T-90
$50 set up Type: doorm |
| 0976 |  | 1 x 3/4 | Moulding 62/12...T-93
$50 set up Type: panlm |
| 0977 |  | 1 x 3/4 | Moulding 62/13...T-94
$50 set up Type: doorm |
| 1249 |  | 1 x 3/8 | Moulding 82/14...T-112
$50 set up Type: doorm |
| 1262 |  | 1 x 3/4 | Moulding 83/08...T-114
$95 set up Type: panlm |
| 1453 |  | 1 x 1 | Moulding 98/08...T-133
$50 set up Type: crndm |
| 1513 |  | 1 x 5/8 | Moulding 102/09...T-146
$50 set up Type: doorm |
| 1515 |  | 1 x 3/4 | Moulding 102/11...T-145
$50 set up Type: doorm |
| 1516 |  | 1 x 9/16 | Moulding 102/12...T-145
$60 set up Type: miscm |
| 1600 |  | 1 x 3/8 | Moulding 109/13...T-153
$50 set up
symmetrical Type: doorm |
| 1628 |  | 1 x 5/8 | Moulding 111/12...T-155
$75 set up
you may spec dado dimensions
Type: panlm |
| 1654 |  | 1 x 3/4 | Moulding 114/04...T-162
$50 set up Type: doorm |
| 1724 |  | 1 x 5/16 | Moulding 119/05...T-166
Beaded
$60 set up Type: cbntm |
| 1728 |  | 1 x 3/4 | Moulding 119/09...T-167
$75 set up Type: panlm |
| 1733 |  | 1 x 13/16 | Moulding 119/14...T-167
$50 set up Type: doorm |
| 1851 |  | 1 x 3/4 | Moulding 130/07...T-179
$50 set up Type: doorm |
| 1874 |  | 1 x 3/8 | Moulding 132/08...T-179
$50 set up Type: doorm |
| 1875 |  | 1 x 3/4 | Moulding 132/09...T-184
$75 set up Type: cbntm |
| 1947 |  | 1 x 5/8 | Moulding 137/03...T-178
$50 set up Type: doorm |
| 1952 |  | 1 x 13/16 | Moulding 137/08...T-174
$75 set up Type: cbntm |
| 2018 |  | 1 x 1/2 | Moulding 151/06...T-172
$50 set up Type: doorm |
| 2083 |  | 1 x 1/2 | Moulding 156/10...T-198
$50 set up Type: doorm |
| 2087 |  | 1 x 1/2 | Moulding 156/14...T-199
$75 set up Type: crndm |
| 2088 |  | 1 x 3/4 | Moulding 156/15...T-200
$75 set up Type: panlm |
| 2119 |  | 1 x 1 | Moulding 159/07...T-203
$75 set up Type: cbntm |
| 0038 |  | 1-1/16 x 1-1/16 | aka 1-1/16" cove
Moulding 02/03...T-8
$60 set up Type: cvbdm |
| 0930 |  | 1-1/16 x 9/16 | Moulding 59/10...T-95
$50 set up Type: doorm |
| 0947 |  | 1-1/16 x 15/16 | full cornered crown
Moulding 60/14...T-90
$50 set up Type: crwnm |
| 0948 |  | 1-1/16 x 3/4 | Moulding 60/15...T-90
$75 set up Type: cbntm |
| 0988 |  | 1-1/16 x 3/4 | Moulding 63/11...T-91
$75 set up Type: cbntm |
| 1206 |  | 1-1/16 x 3/8 | Moulding 79/13...T-127
$50 set up Type: doorm |
| 1242 |  | 1-1/16 x 13/16 | Moulding 82/07...T-113
$75 set up Type: panlm |
| 1335 |  | 1-1/16 x 1 | Moulding 88/05...T-142
$50 set up Type: doorm |
| 1460 |  | 1-1/16 x 3/4 | Moulding 99/03...T-138
$50 set up Type: doorm |
| 1723 |  | 1-1/16 x 1-1/16 | Moulding 119/04...T-166 Type: panlm |
| 1953 |  | 1-1/16 x 3/4 | Moulding 137/09...T-178
$75 set up Type: cbntm |
| 1985 |  | 1-1/16 x 11/16 | Moulding 139/12...T-179
$50 set up Type: doorm |
| 2059 |  | 1-1/16 x 1/4 | Moulding 154/13...T-193
$60 set up Type: doorm |
| 0041 |  | 1-1/8 x 1-1/4 | tall DM-3
Moulding 03/01...T-5
$50 set up Type: crndm |
| 0050 |  | 1-1/8 x 3/4 | Moulding 03/11...T-8
$50 set up Type: crndm |
| 0201 |  | 1-1/8 x 7/16 | dado can be spec'd
Moulding 15/05...T-29
Symmetrical
$95.00 set-up Type: miscm |
| 0267 |  | 1-1/8 x 1/2 | symmetrical
Moulding 19/10...T-24
$50 set up
Type: doorm |
| 0326 |  | 1-1/8 x 9/16 | Moulding 145/08...T-37
aka DM130
$50 set up Type: doorm |
| 0357 |  | 1-1/8 x 1 | panel cap
dado can be spec'd
Moulding 25/03...T-36
$75 set up Type: panlm |
| 0370 |  | 1-1/8 x 13/16 | Moulding 25/16...T-41
$50 set up Type: doorm |
| 0405 |  | 1-1/8 x 11/16 | Moulding 27/16...T-43
$50 set up Type: doorm |
| 0407 |  | 1-1/8 x 1/2 | Moulding 146/03...T-43
symmetrical
$50 set up Type: doorm |
| 0536 |  | 1-1/8 x 9/16 | Moulding 147/05...T-43
$50 set up Type: doorm |
| 0794 |  | 1-1/8 x 1 | 3/4" offset for block paneling
dado can be spec'd
Moulding 46/07...T-
$75 set up Type: panlm |
| 0828 |  | 1-1/8 x 11/16 | Moulding 51/15...T-83
$50 set up Type: doorm |
| 0931 |  | 1-1/8 x 3/4 | Moulding 59/11...T-89
$50 set up Type: doorm |
| 1012 |  | 1-1/8 x 3/4 | Moulding 65/08...T-95
$50 set up Type: panlm |
| 1015 |  | 1-1/8 x 13/16 | Moulding 65/11...T-94
$50 set up Type: doorm |
| 1018 |  | 1-1/8 x 9/16 | Moulding 65/14...T-87
$50 set up Type: doorm |
| 1121 |  | 1-1/8 x 5/8 | Moulding 76/07...T-99
$50 set up Type: doorm |
| 1126 |  | 1-1/8 x 1 | Moulding 76/12...T-108
$50 set up
beaded Type: panlm |
| 1232 |  | 1-1/8 x 7/16 | Moulding 81/11...T-117
$50 set up Type: doorm |
| 1233 |  | 1-1/8 x 11/16 | similatr to the stock PM-5
Moulding 81/12...T-120
$50 set up Type: panlm |
| 1248 |  | 1-1/8 x 3/4 | Moulding 82/13...T-114
$50 set up Type: doorm |
| 1366 |  | 1-1/8 x 1/2 | Moulding 90/13...T-130
$50 set up Type: doorm |
| 1473 |  | 1-1/8 x 3/4 | Moulding 99/16...T-139
$75 set up Type: cbntm |
| 1626 |  | 1-1/8 x 3/4 | Moulding 111/10...T-155
$50 set up Type: miscm |
| 1660 |  | 1-1/8 x 3/4 | Moulding 114/10...T-160
$50 set up Type: doorm |
| 1689 |  | 1-1/8 x 13/16 | Moulding 116/11...T-163 Type: panlm |
| 1690 |  | 1-1/8 x 1 | Moulding 116/12...T-162
$95 set up Type: crndm |
| 1725 |  | 1-1/8 x 3/4 | Moulding 119/06...T-166
$75 set up Type: doorm |
| 1901 |  | 1-1/8 x 1 | Moulding 134/07...T-181
$75 set up Type: cbntm |
| 1936 |  | 1-1/8 x 3/4 | Moulding 136/11...T-174
$75 set up Type: cbntm |
| 1948 |  | 1-1/8 x 9/16 | Moulding 137/04...T-
$50 set up Type: doorm |
| 1959 |  | 1-1/8 x 1 | Moulding 137/15...T-193
$50 set up Type: doorm |
| 0192 |  | 1-3/16 x 11/16 | Moulding 14/08...T-45
similar to DM3
$50 set up Type: doorm |
| 0493 |  | 1-3/16 x 1-1/4 | Moulding 32/09...T-57
$75 set up Type: crndm |
| 0567 |  | 1-3/16 x 3/4 | Moulding 148/06...T-53
$75 set up Type: cbntm |
| 1201 |  | 1-3/16 x 5/8 | Moulding 79-09...T-114
$75 set up
Type: panlm |
| 1231 |  | 1-3/16 x 9/16 | Moulding 81/10...T-112
$50 set up Type: doorm |
| 1261 |  | 1-3/16 x 9/16 | Symmetrical
Moulding 83/07...T-121
$50 set up Type: doorm |
| 1518 |  | 1-3/16+ x 1/2 | Moulding 102/14...T-147
$75 set up (with back angled) Type: bbrdm |
| 0093 |  | 1-1/4 x 5/8 | Moulding 07/08...T-9
$50 set up Type: doorm |
| 0113 |  | 1-1/4 x 1 | Moulding 09/13...T-17
$50 set up Type: crwnm |
| 0216 |  | 1-1/4 x 11/16 | slightly different than basic PM-5
Moulding 150/03...T-29
$50 set up Type: panlm |
| 0231 |  | 1-1/4 x 15/16 | 1" lip mold but can also be used for picture frame material
beaded lip
Moulding 17/06...T-38
$75 set up Type: cbntm |
| 0259 |  | 1-1/4 x 3/4 | Moulding 19/04...T-31
$50 set up Type: doorm |
| 0291 |  | 1-1/4 x 3/4 | slightly different than PM-5
Moulding 149/05...T-25
$50 set up Type: panlm |
| 0316 |  | 1-1/4 x 5/8 | Moulding 22/08...T-35
$50 set up Type: doorm |
| 0329 |  | 1-1/4 x 3/4 | slightly different tham PM-5
Moulding 22/20...T-29
$50 set up Type: panlm |
| 0333 |  | 1-1/4 x 15/16 | Moulding 23/04...T-28
$50 set up Type: doorm |
| 0358 |  | 1-1/4 x 1/2 | Moulding 25/04...T-36
$50 set up Type: doorm |
| 0360 |  | 1-1/4 x 7/8 | dado can be varied
Moulding 25/06...T-36
$75 set up Type: panlm |
| 0400 |  | 1-1/4 x 1-1/8 | dado can be varied
Moulding 27/11...T-34
$75 set up Type: panlm |
| 0422 |  | 1-1/4 x 13/16 | double humped...very unique bead
Moulding 28/07...T-20
$50 set up Type: panlm |
| 0453 |  | 1-1/4 x 1/4+ | used to simulate beaded casing, can be made thicker for more definition.
symmetrical
Moulding 31/13...T-54
$60 set up
Type: cbntm |
| 0466 |  | 1-1/4 x 1/2 | Moulding 30/08...T-49
$50 set up Type: doorm |
| 0498 |  | 1-1/4 x 1/4 | Moulding 32/17...T-46
$50 set up Type: doorm |
| 0526 |  | 1-1/4 x 3/4 | Moulding 34/04...T-55
$50 set up Type: cvbdm |
| 0538 |  | 1-1/4 x 3/4 | slightly different tham PM-5
Moulding 143/14...T-48
$50 set up Type: panlm |
| 0545 |  | 1-1/4 x 3/4 | Moulding 35/06...T-50
$50 set up
beaded Type: custo |
| 0635 |  | 1-1/4 x 3/4 | Moulding 39/11...T-
$50 set up Type: doorm |
| 0795 |  | 1-1/4 x 3/4 | custom lip mould
Moulding 46/08...T-68
$75 set up Type: cbntm |
| 0878 |  | 1-1/4 x 3/4 | Moulding 55/09...T-85
$50 set up Type: doorm |
| 0884 |  | 1-1/4 x 11/16 | Moulding 55/15...T-84
$50 set up
also can be made to DM-4
11/16"x1"
Symmetrical Type: doorm |
| 0941 |  | 1-1/4 x 15/16 | Moulding 60/08...T-91
$50 set up Type: panlm |
| 1000 |  | 1-1/4 x 5/8 | Moulding 64/10...T-94
$50 set up Type: doorm |
| 1122 |  | 1-1/4 x 11/16 | Symmetrical
Moulding 76/08...T-109
$50 set up
Type: doorm |
| 1125 |  | 1-1/4 x 3/4 | Moulding 76/11...T-99
$50 set up Type: doorm |
| 1150 |  | 1-1/4 x 1-1/4 | dado can be spec'd
Moulding 74/12...T-106
$75 set up Type: panlm |
| 1152 |  | 1-1/4 x 1-9/16 | dado can be spec'd
Moulding 74/14...T-106
$75 set up Type: panlm |
| 1205 |  | 1-1/4 x 13/16 | Moulding 79/12...T-125
$95 set up Type: cbntm |
| 1254 |  | 1-1/4 x 9/16 | Moulding 82/19...T-112
$75 set up Type: panlm |
| 1303 |  | 1-1/4 x 13/16 | Moulding 86/09...T-118
$75 set up please specify gap dimensions Type: panlm |
| 1313 |  | 1-1/4 x 3/4 | Moulding 86/15...T-130
$50 set up Type: doorm |
| 1393 |  | 1-1/4 x 13/16 | Moulding 92/13...T-139
$75 set up
makes fake louver door inserts Type: miscm |
| 1394 |  | 1-1/4 x 3/8 | Moulding 92/14...T-128
$60 set up Type: doorm |
| 1395 |  | 1-1/4 x 7/8 | Moulding 92/15...T-142
similar to pm-5
$50 set up
Type: panlm |
| 1400 |  | 1-1/4 x 15/16 | Moulding 92/20...T-137
$75 set up please spec gap dimensions Type: panlm |
| 1408 |  | 1-1/4 x 1-1/4 | Moulding 93/06...T-141
$50 set up
full cornered crown Type: crwnm |
| 1464 |  | 1-1/4 x 3/4 | Moulding 99/07...T-139
$75 set up
Symmetrical Type: doorm |
| 1468 |  | 1-1/4 x 15/16 | Moulding 99/11...T-130
$75 set up Type: panlm |
| 1480 |  | 1-1/4 x 1-1/8 | Moulding 99/22...T-143
$75 set up Type: panlm |
| 1517 |  | 1-1/4 x 3/4 | Moulding 102/13...T-146
$75 set up Type: panlm |
| 1558 |  | 1-1/4 x 11/16 | Moulding 106/06...T-147
$75 set up Type: panlm |
| 1576 |  | 1-1/4 x 3/4 | Moulding 107/13...T-151
$75 set up Type: panlm |
| 1598 |  | 1-1/4 x 13/16 | Moulding 109/11...T-154
$50 set up Type: doorm |
| 1646 |  | 1-1/4 x 5/8 | Moulding 113/08...T-158
$50 set up Type: doorm |
| 1664 |  | 1-1/4 x 1-1/8 | Moulding 114/14...T-160
$50 set up Type: doorm |
| 1842 |  | 1-1/4 x 13/16 | Moulding 129/11...T-178
$50 set up Type: doorm |
| 1873 |  | 1-1/4 x 7/16 | Moulding 132/07...T-186
$50 set up Type: doorm |
| 1928 |  | 1-1/4 x 3/4 | Moulding 136/03...T-179
$60 set up Type: crwnm |
| 1951 |  | 1-1/4 x 5/16 | Moulding 137/07...T-174
$50 set up Type: doorm |
| 2056 |  | 1-1/4 x 3/4 | Moulding 154/10...T-194
$80 set up Type: panlm |
| 2057 |  | 1-1/4 x 1/2 | Moulding 154/11...T-194
$50 set up Type: doorm |
| 2108 |  | 1-1/4 x 3/4 | Moulding 158/09...T-203
$50 set up Type: doorm |
| 0139 |  | 1-5/16 x 1/2 | Moulding 12/06...T-45
$60 set up Type: doorm |
| 0279 |  | 1-5/16 x 1-5/16 | OSC
Moulding 143/13...T-24
$125 set up Type: crndm |
| 1128 |  | 1-5/16 x 3/4 | dado can be spec'd
Moulding 76/14...T-109
$75 set up Type: panlm |
| 1316 |  | 1-5/16 x 1/2 | Moulding 87/03...T-83
$95 set up Type: miscm |
| 1722 |  | 1-5/16 x 7/8 | Moulding 119/03...T-166 Type: panlm |
| 1814 |  | 1-5/16 x 3/4 | Moulding 127/06...T-191
$50 set up Type: doorm |
| 0046 |  | 1-3/8 x 1/2 | Moulding 03/07...T-13
similar to LSDM130
$50 set up Type: doorm |
| 0049 |  | 1-3/8 x 3/4 | dado can be varied
Moulding 03/10...T-4
aka LSPM1 pm-1
$75 set up Type: panlm |
| 0063 |  | 1-3/8 x 5/8 | Moulding 05/03..T-2
$50 set up Type: chrrm |
| 0223 |  | 1-3/8 x 1-1/4 | Moulding 17/01...T-40
$50 set up Type: miscm |
| 0239 |  | 1-3/8 x 13/16 | custom lip mold
Moulding 17/11...T-33
aka LSCM11
$75 set up Type: cbntm |
| 0256 |  | 1-3/8 x 1/4+ | Symmetrical
Moulding 19/01...T-40
$60 set up Type: doorm |
| 0262 |  | 1-3/8 x 13/16 | Moulding 19/06...T-31
$50 set up Type: doorm |
| 0268 |  | 1-3/8 x 3/8 | Moulding 19/11...T-24
$85 set up Type: cvbdm |
| 0319 |  | 1-3/8 x 7/16 | Moulding 22/11...T-35
$50 set up Type: doorm |
| 0359 |  | 1-3/8 x 3/4 | Moulding 25/05...T-36
$50 set up Type: doorm |
| 0456 |  | 1-3/8 x 3/4 | used around the 3/4" plywood for cabinet doors
Moulding 31/15...T-54
$135 set up
Type: cbntm |
| 0671 |  | 1-3/8 x 3/4 | Moulding 41/14...T-64
$50 set up.
Close to DM7 Type: doorm |
| 0843 |  | 1-3/8 x 1/2 | wainscoat cap
Moulding 52/14...T-85
$75 set up Type: panlm |
| 0850 |  | 1-3/8 x 7/8 | 5/8" offset shown
Moulding 53/07...T-84
$75 set up Type: panlm |
| 0854 |  | 1-3/8 x 13/16 | panel cap
Moulding 53/11...T-78
$75 set up Type: panlm |
| 0881 |  | 1-3/8 x 3/4 | Moulding 55/12...T-35
$50 set up Type: doorm |
| 0942 |  | 1-3/8 x 3/4 | Symmetrical
Moulding 60/09...T-96
$50 set up Type: doorm |
| 1013 |  | 1-3/8 x 3/4 | Moulding 65/09...T-92
$50 set up Type: cvbdm |
| 1025 |  | 1-3/8 x 1-1/4 | Moulding 141/04...T-
$120 set up
dado can be specified
symmetrical Type: hrail |
| 1120 |  | 1-3/8 x 1-1/8 | Moulding 76/06...T-100
$50 set up Type: miscm |
| 1129 |  | 1-3/8 x 13/16 | Moulding 76/15...T-108
$50 set up Type: doorm |
| 1130 |  | 1-3/8 x 1/2 | Moulding 76/16...T-13
$59 set up Type: doorm |
| 1131 |  | 1-3/8 x 5/8 | Moulding 76/17...T-105
$50 set up Type: panlm |
| 1132 |  | 1-3/8 x 1/2 | Symmetrical
Moulding 76/18...T-105
$50 set up Type: doorm |
| 1163 |  | 1-3/8 x 3/4 | 3/4" offset shown, you may spec another dimension, beaded lip
Moulding 75/09...T-102
$75 set up Type: cbntm |
| 1234 |  | 1-3/8 x 5/8 | Moulding 81/13...T-115
$50 set up Type: doorm |
| 1243 |  | 1-3/8 x 1-1/16 | Moulding 82/08...T-114
$75 set up
rooster Type: panlm |
| 1250 |  | 1-3/8 x 3/4 | Moulding 82/15...T-119
$50 set up Type: doorm |
| 1363 |  | 1-3/8 x 1 | Moulding 90/10...T-129
dado can be specified
$75 set up Type: panlm |
| 1367 |  | 1-3/8 x 3/4 | Moulding 90/14...T-136
$50 set up Type: panlm |
| 1368 |  | 1-3/8 x 9/16 | Moulding 90/15...T-136
$60 set up Type: doorm |
| 1369 |  | 1-3/8 x 7/8 | Moulding 90/16...T-131
$50 set up Type: doorm |
| 1387 |  | 1-3/8 x 3/4 | Moulding 92/07...T-105
$75 set up, add .30 to run twice
symmetrical Type: miscm |
| 1452 |  | 1-3/8 x 1-1/8 | Moulding 98/07...T-140
$50 set up
full cornered crown Type: crwnm |
| 1454 |  | 1-3/8 x 1-1/8 | Moulding 98/09...T-138
$50 set up
full cornered crown Type: crwnm |
| 1467 |  | 1-3/8 x 3/4 | Moulding 99/10...T-114
$50 set up Type: doorm |
| 1634 |  | 1-3/8 x 3/4 | Moulding 112/06...T-157
$75 set up Type: panlm |
| 1726 |  | 1-3/8 x 5/8 | Moulding 119/07...T-167
window mullion
set up $75 add .30 to run twice Type: miscm |
| 1727 |  | 1-3/8 x 3/4 | Moulding 119/08...T-66
window mullion
set up $75 add .30 to run twice Type: miscm |
| 1729 |  | 1-3/8 x 3/4 | Moulding 119/10...T-167 Type: panlm |
| 1824 |  | 1-3/8 x 11/16 | Moulding 128/05...T-188
$50 set up Type: doorm |
| 1941 |  | 1-3/8 x 5/8 | Moulding 136/16...T-182
$50 set up Type: doorm |
| 1942 |  | 1-3/8 x 3/4 | Moulding 136/17...T-177
$50 set up
Type: doorm |
| 1978 |  | 1-3/8 x 3/4 | Moulding 139/05...T-186
$50 set up Type: doorm |
| 2060 |  | 1-3/8 x 5/8 | Moulding 154/14...T-198
$50 set up Type: doorm |
| 2079 |  | 1-3/8 x 1/2 | Moulding 156/06...T-199
$50 set up Type: doorm |
| 2105 |  | 1-3/8 x 5/8 | Moulding 158/06...T-202
$50 set up Type: doorm |
| 2109 |  | 1-3/8 x 3/4 | Moulding 158/10...T-202. Finger pull.
$85 set up Type: cbntm |
| 2124 |  | 1-3/8 x 1-3/8 | Moulding 159/12...T-203
$75 set up Type: panlm |
| 2125 |  | 1-3/8 x 1/2 | Moulding 159/13...T-202
$50 set up Type: doorm |
| 1127 |  | 1-7/16 x 1-3/8 | Moulding 76/13...T-101
$50 set up Type: miscm |
| 1203 |  | 1-7/16 x 3/4 | Moulding 79/11...T-126
beaded lip
$75 set up Type: cbntm |
| 1396 |  | 1-7/16 x 1/2 | Moulding 92/16...T-136
$50 set up Type: doorm |
| 1498 |  | 1-7/16 x 7/8 | Moulding 101/08...T-145
$50 set up Type: doorm |
| 0020 |  | 1-1/2 x 3/4 | used on the bottom of cabinet doors for a finger pull
Moulding 01/01...T-17
$90 set up
Type: cbntm |
| 0033 |  | 1-1/2 x 1/2 | Moulding 02/08...T-3
$75 set up Type: panlm |
| 0085 |  | 1-1/2 x 1-1/2 | aka 1-1/2" bullnose, can be any different height
Moulding 06/07...T-10
Symmetrical
$50 set up Type: crndm |
| 0149 |  | 1-1/2 x 1-1/2 | aka 1-1/2" qtr round
Moulding 12/12...T-19
$85 set up
2" quarter round set up is $90 set up.
Type: crndm |
| 0185 |  | 1-1/2 x 3/4 | could be panel cap or picture frame molding
dado can be spec'd
Moulding 14/02...T-3
$75 set up Type: miscm |
| 0204 |  | 1-1/2 x 13/16 | Moulding 15/07...T-19
similar to CM1 too
$50 set up Type: doorm |
| 0269 |  | 1-1/2 x 1 | Moulding 19/12...T-24
similar to CM1
$50 set up Type: doorm |
| 0317 |  | 1-1/2 x 3/4 | Moulding 22/09...T-31
$50 set up Type: doorm |
| 0408 |  | 1-1/2 x 1-1/2 | Moulding 148/08...T-34
$50 set up Type: crndm |
| 0457 |  | 1-1/2 x 5/8 | Moulding 30/04...T-49
$50 set up Type: doorm |
| 0465 |  | 1-1/2 x 1-1/16 | used around the perimeter of 5/8" plywood used for cabinet doors.
Moulding 144/08...T-54
$95 set up Type: cbntm |
| 0469 |  | 1-1/2 x 5/8 | Moulding 143/11...T-10
Symmetrical
$50 set up
Type: miscm |
| 0509 |  | 1-1/2 x 3/8 | Moulding 33/09...T-49
$60 set up Type: doorm |
| 0544 |  | 1-1/2 x 3/4 | symmetrical, beaded
Moulding 35/05...T-56
$50 set up Type: chrrm |
| 0561 |  | 1-1/2 x 3/8 | Moulding 35/15...T-53
$50 set up Type: doorm |
| 0562 |  | 1-1/2 x 5/8+ | Moulding 35/16...T-52
$50 set up Type: doorm |
| 0583 |  | 1-1/2 x 3/4 | Moulding 141/08...T-53
$50 set up
Symmetrical Type: doorm |
| 0601 |  | 1-1/2 x 1 | Moulding 37/12...T-52
$95 set up, $75 w/out notch Type: doorm |
| 0614 |  | 1-1/2 x 1-1/2 | large outside corner,(OSC)...covers one inch
Moulding 38/07...T-60
$120.00 set-up using 8/4 stock
or 6/4 x 2" blank size...run diagonally with $75 set up Type: crndm |
| 0653 |  | 1-1/2 x 1-1/16 | Moulding 40/06...T-59
$60 set up Type: cvbdm |
| 0796 |  | 1-1/2 x 3/4 | Moulding 46/09...T-73
$50 set up Type: doorm |
| 0802 |  | 1-1/2 x 1/2 | Moulding 47/02...T-71
$50 set up Type: doorm |
| 0827 |  | 1-1/2 x 9/16 | Symmetrical
Moulding 51/14...T-82
$60 set up Type: doorm |
| 0868 |  | 1-1/2 x 1-1/2 | Moulding 54/10...T-79
$50 set up Type: doorm |
| 0879 |  | 1-1/2 x 15/16 | Moulding 55/10...T-85
$50 set up Type: doorm |
| 0882 |  | 1-1/2 x 3/4 | like a small brick mould
Moulding 55/13...T-84
$50 set up Type: doorm |
| 0883 |  | 1-1/2 x 5/8 | Symmetrical
The notch was for an inlay piece of brass
Moulding 55/14...T-85
$75 set up Type: chrrm |
| 0929 |  | 1-1/2+ x 3/4+ | Moulding 59/09...T-
bead
$75 set up Type: miscm |
| 0932 |  | 1-1/2 x 1 | full cornered crown
Moulding 59/12...T-88
$50 set up Type: crwnm |
| 0946 |  | 1-1/2 x 7/8 | Moulding 60/13...T-95
$50 set up Type: doorm |
| 0961 |  | 1-1/2 x 1 | dado can be spec'd
Moulding 61/10...T-87
$75 set up Type: panlm |
| 0996 |  | 1-1/2 x 1-3/8 | Moulding 64/06...T-88
$95 set up Type: doorm |
| 0998 |  | 1-1/2 x 1-1/2 | Moulding 64/08...T-92
$75 set up Type: doorm |
| 1001 |  | 1-1/2 x 1/2 | Moulding 64/11...T-93
$50 set up Type: doorm |
| 1011 |  | 1-1/2 x 1-1/2 | Moulding 65/07...T-94
$50 set up Type: doorm |
| 1105 |  | 1-1/2 x 3/4 | Symmetrical
Moulding 73/12...T-13
$50 set up Type: chrrm |
| 1117 |  | 1-1/2 x 1-1/2 | Moulding 76/03...T-105
$50 set up Type: doorm |
| 1146 |  | 1-1/2 x 3/4 | Symmetrical
Moulding 74/08...T-98
$50 set up Type: doorm |
| 1198 |  | 1-1/2 x 1-1/8 | Moulding 79/06...T-125
$50 set up Type: doorm |
| 1282 |  | 1-1/2 x 1-1/4 | Moulding 85/02...T-118
$75 set up
symmetrical Type: hrail |
| 1304 |  | 1-1/2 x 7/8 | Moulding 86/10...T-119
$50 set up Type: doorm |
| 1370 |  | 1-1/2 x 3/4 | Moulding 90/17...T-139
$50 set up Type: doorm |
| 1371 |  | 1-1/2 x 3/4 | Moulding 90/18...T-114
$50 set up Type: doorm |
| 1382 |  | 1-1/2 x 1-1/8 | Moulding 92/02...T-140
$50 set up Type: panlm |
| 1389 |  | 1-1/2 x 1 | Moulding 92/09...T-129
$75 set up
you can spec the dado dimensions Type: cbntm |
| 1390 |  | 1-1/2 x 3/4 | Moulding 92/10...T-137
$85 set up
used for bottom of cabinet doors, see the finger pull Type: cbntm |
| 1391 |  | 1-1/2 x 1/2 | Moulding 92/11...T-136
$50 set up Type: doorm |
| 1458 |  | 1-1/2 x 1-3/16 | Moulding 99/01...T-136
$95 set up Type: miscm |
| 1466 |  | 1-1/2 x 5/8 | Moulding 99/09...T-141
$50 set up Type: doorm |
| 1476 |  | 1-1/2 x 11/16 | Moulding 99/18...T-143
$50 set up Type: doorm |
| 1477 |  | 1-1/2 x 3/4 | Moulding 99/19...T-143
$50 set up Type: doorm |
| 1501 |  | 1-1/2 x 7/8 | Moulding 101/11...T-144
$75 set up Type: panlm |
| 1502 |  | 1-1/2 x 1-3/8 | Moulding 101/12...T-143
$50 set up Type: doorm |
| 1533 |  | 1-1/2 x 3/4 | Moulding 104/06...T-82
$50 set up Type: miscm |
| 1645 |  | 1-1/2 x 13/16 | Moulding 113/07...T-159
$75 set up Type: cbntm |
| 1684 |  | 1-1/2 x 3/4 | Moulding 116/06...T-
$75 set up Type: doorm |
| 1692 |  | 1-1/2 x 3/8 | Moulding 116/14...T-162
$50 set up Type: doorm |
| 1711 |  | 1-1/2 x 13/16 | Moulding 118/06...T-165
$75 set up
please spec the dado width Type: cbntm |
| 1713 |  | 1-1/2 x 3/4 | Moulding 118/08...T-164
$75 set up Type: cbntm |
| 1718 |  | 1-1/2 x 1-1/2 | Moulding 118/13...T-165
$50 set up
full cornered crown Type: crwnm |
| 1730 |  | 1-1/2 x 3/4 | Moulding 119/11...T-167
$50 set up Type: doorm |
| 1755 |  | 1-1/2 x 1-3/8 | Moulding 121/11...T-171
$60 set up
full cornered crown Type: crwnm |
| 1795 |  | 1-1/2 x 13/16 | Moulding 125/09...T-193
$50 set up Type: doorm |
| 1827 |  | 1-1/2 x 13/16 | Moulding 128/08...T-141
$50 set up Type: doorm |
| 1844 |  | 1-1/2 x 1-1/4 | Moulding 129/12...T-192
$50 set up Type: doorm |
| 1905 |  | 1-1/2 x 13/16 | Moulding 134/11...T-181
$50 set up Type: doorm |
| 1906 |  | 1-1/2 x 1-1/8 | Moulding 134/12...T-179
$75 set up as shown
$50 set up w/out dado on bottom Type: chrrm |
| 1907 |  | 1-1/2 x 1-1/8 | Moulding 134/13...T-182
$75 set up
used inside perimeter of raised paneled doors
rooster Type: panlm |
| 1917 |  | 1-1/2 x 1 | Moulding 135/06...T-179
$75 set up
you can specify dado dimensions Type: doorm |
| 1940 |  | 1-1/2 x 15/16 | Moulding 136/15...T-172
$50 set up Type: panlm |
| 1957 |  | 1-1/2 x 3/4 | Moulding 137/13...T-186
$50 set up Type: doorm |
| 1994 |  | 1-1/2 x 3/4 | Moulding 161/06...T-205
$75 set up Type: cbntm |
| 2055 |  | 1-1/2 x 1-1/16 | Moulding 154/09...T-194
$50 set up Type: chrrm |
| 2064 |  | 1-1/2 x 3/4 | Moulding 155/03...T-198
$50 set up Type: chrrm |
| 2070 |  | 1-1/2 x 1-1/2 | Moulding 155/09...T-194
$60 set up Type: miscm |
| 2080 |  | 1-1/2 x 9/16 | Moulding 156/07...T-201
$50 set up Type: doorm |
| 2086 |  | 1-1/2 x 1 | Moulding 156/13...T-198
$85 set up
Type: panlm |
| 2110 |  | 1-1/2 x 7/8 | Moulding 158/11...T-202
$75 set up Type: chrrm |
| 2121 |  | 1-1/2 x 1-1/4 | Moulding 159/09...T-
perfect 60 degree triangle
$75 set up Type: miscm |
| 2126 |  | 1-1/2 x 1/2 | Moulding 159/14...T-
$75 set up Type: miscm |
| 0135 |  | 1-9/16 x 13/16 | used at the bottom of cabinet doors as a finger pull for full overlay doors
Moulding 12/03...T-16
$95 set up Type: cbntm |
| 0205 |  | 1-9/16 x 1-1/2 | wall/stairs rail mounted with brackets to wall
Moulding 16/02...T-10
$85 set up
symmetrical Type: hrail |
| 0236 |  | 1-9/16 x 1 | Moulding 17/09...T-33
beads
$50 set up Type: chrrm |
| 0467 |  | 1-9/16 x 1/2 | Moulding 142/11...T-1
$95 set up Type: crwnm |
| 0482 |  | 1-9/16 x 3/4 | wainscott cap
dado can be spec'd
Moulding 32/01...T-57
$75 set up Type: panlm |
| 0839 |  | 1-9/16 x 5/8 | Moulding 52/10...T-81
$60 set up...add $.30/lf to run twice
Symmetrical Type: miscm |
| 1504 |  | 1-9/16 x 7/8 | Moulding 101/14...T-144
$50 set up Type: doorm |
| 0121 |  | 1-5/8 x 3/4 | this picture shows a 1/4" offset for a beaded panel cap. If you need this for lip moulding specify 3/8" offset.
Moulding 10/03...T-14
$75 set up
Type: cbntm |
| 0314 |  | 1-5/8 x 1 | another custom lip mold
Moulding 22/06...T-35
$75 set up Type: cbntm |
| 0519 |  | 1-5/8 x 1-5/8 | Moulding 148/07...T-57
$60 set up Type: cvbdm |
| 0528 |  | 1-5/8 x 11/16+ | Moulding 34/06...T-48
$50 set up Type: doorm |
| 0711 |  | 1-5/8 x 5/8 | Photo is shown without 3/8 x 3/8 lip.
Moulding 44/04...T-66
$50 set up as shown; $75 set up with lip. Type: cbntm |
| 0726 |  | 1-5/8 x 1-5/16 | the lip is 3/4" to cover the edge of plywood
CM-34Moulding 48/05...T-35
$75 set up
Type: cbntm |
| 0799 |  | 1-5/8 x 3/8 | Moulding 46/12...T-66
$50 set up Type: doorm |
| 0803 |  | 1-5/8 x 13/16 | Moulding 47/03...T-72
$50 set up Type: doorm |
| 0826 |  | 1-5/8 x 13/16 | 1-5/8 half round
Symmetrical
Moulding 51/13...T-17
$50 set up
We also have a 1-3/4" half round Type: crndm |
| 0840 |  | 1-5/8 x 3/8 | Moulding 52/11...T-80
shown without the 3/8" lip
$50 set up Type: cbntm |
| 1016 |  | 1-5/8 x 7/8 | Moulding 65/12...T-91
$50 set up Type: doorm |
| 1020 |  | 1-5/8 x 13/16 | Moulding 65/16...T-93
$75 set up Type: doorm |
| 1241 |  | 1-5/8 x 1-3/16 | Moulding 82/06...T-116
$75 set up Type: panlm |
| 1244 |  | 1-5/8 x 1 | Moulding 82/09...T-114
$95 set up
rooster Type: cbntm |
| 1252 |  | 1-5/8 x 13/16 | Moulding 82/17...T-112
$75 set up Type: cbntm |
| 1253 |  | 1-5/8 x 13/16 | Moulding 82/18...T-118
$95 set up Type: cbntm |
| 1260 |  | 1-5/8 x 9/16 | Moulding 83/06...T-114
$75 set up Type: panlm |
| 1388 |  | 1-5/8 x 1-1/8 | Moulding 92/08...T-130
$75 set up, add .30 to run twice Type: miscm |
| 1397 |  | 1-5/8 x 7/16 | Moulding 92/17...T-133
$50 set up Type: doorm |
| 1462 |  | 1-5/8 x 1-1/8 | Moulding 99/05...T-130
$75 set up, add .30 to run twice Type: miscm |
| 1463 |  | 1-5/8 x 1 | Moulding 99/06...T-127
$75 set up, please specify gap dimensions Type: panlm |
| 1551 |  | 1-5/8 x 7/8 | Moulding 105/12...T-148
$50 set up Type: doorm |
| 1557 |  | 1-5/8 x 7/8 | Moulding 106/05...T-148
$85 set up Type: cbntm |
| 1559 |  | 1-5/8 x 13/16 | Moulding 106/07...T-147
$95 set up Type: cbntm |
| 1644 |  | 1-5/8 x 1-1/4 | Moulding 113/06...T-158
$75 set up Type: panlm |
| 1682 |  | 1-5/8 x 13/16 | Moulding 116-04...T-162
$75 set up Type: panlm |
| 1683 |  | 1-5/8 x 3/4 | Moulding 116/05...T-163
$50 set up Type: doorm |
| 1688 |  | 1-5/8 x 1-1/16 | Moulding 116/10...T-162
$75 set up Type: panlm |
| 1714 |  | 1-5/8 x 3/4 | Moulding 118/09...T-165
$75 set up Type: cbntm |
| 1748 |  | 1-5/8 x 1-1/2 | Moulding 121/04...T-169
$75 set up Type: panlm |
| 1849 |  | 1-5/8 x 1-1/2 | Moulding 130/05...T-182
$75 set up
add $.40 per foot to run twice Type: hrail |
| 1909 |  | 1-5/8 x 1-1/8 | Moulding 134/15...T-
$75 set up Type: panlm |
| 1937 |  | 1-5/8 x 3/4 | Moulding 136/12...T-178
$50 set up Type: panlm |
| 1954 |  | 1-5/8 x 7/8 | Moulding 137/10...T-171
$75 set up Type: panlm |
| 1986 |  | 1-5/8 x 11/16 | Moulding 139/13...T-175
$75 set up Type: panlm |
| 1997 |  | 1-5/8 x 13/16 | Moulding 161/09...T-205
$75 set up Type: cbntm |
| 2058 |  | 1-5/8 x 3/8 | Moulding 154/12...T-193
$60 set up Type: chrrm |
| 2104 |  | 1-5/8 x 9/16 | Moulding 158/05...T-203
$50 set up Type: doorm |
| 2120 |  | 1-5/8 x 13/16 | Moulding 159/08...T-202
$95 set up Type: cbntm |
| 0181 |  | 1-11/16 x 3/4 | Moulding 11/10...T-16
$75 set up Type: cbntm |
| 0308 |  | 1-11/16 x 1-1/16 | panel cap
dado can be spec
Moulding 148/14...T-35
$75 set up Type: panlm |
| 0309 |  | 1-11/16 x 1-1/8 | Moulding 147/08...T-25
aka BMC203, (OSC)
$80 set up
price as 1-1/8 X 1-5/8 (6/4 stock) Type: crndm |
| 0772 |  | 1-11/16 x 13/16 | typical 3/8" offset
Moulding 50/12...T-74
$75 set up Type: cbntm |
| 0880 |  | 1-11/16 x 11/16 | Moulding 55/11...T-85
$50 set up
Type: doorm |
| 1385 |  | 1-11/16 x 3/4 | Moulding 92/05...T-133
$50 set up Type: chrrm |
| 2107 |  | 1-11/16 x 1-1/16 | Moulding 158/08...T-203
$75 set up
window mullion Type: miscm |
| 0024 |  | 1-3/4 x 7/8 | Moulding 01/05...T-45 degrees
$95 set up
symmetrical Type: custo |
| 0062 |  | 1-3/4 x 3/4 | Moulding 05/02...T-2
$50 set up
an old Boren Mldg Type: chrrm |
| 0075 |  | 1-3/4 x 1/2 | dado can be spec'd
Moulding 06/01...T-3
$75 set up Type: panlm |
| 0143 |  | 1-3/4 x 3/4 | aka picture mold. discontinued as s.t.o.c.k item
Moulding 12/09...T-44
$75 set up Type: miscm |
| 0179 |  | 1-3/4 x 1 | Moulding 10/10...T-14
$50 set up Type: chrrm |
| 0261 |  | 1-3/4 x 1-1/8 | Moulding 19/05...T-24
$75 set up Type: cbntm |
| 0297 |  | 1-3/4 x 31/32 | flooring made to match hard to find size
Moulding 21/05...T-32
all tongue and grooves are $95 set-up Type: miscm |
| 0301 |  | 1-3/4 x 3/4 | Moulding 21/09...T-35
$95 set up
Type: crwnm |
| 0324 |  | 1-3/4 x 1 | Moulding 22/15...T-31
$60 set up Type: cvbdm |
| 0341 |  | 1-3/4 x 9/16 | symmetrical
Moulding 23/11...T-32
$75 set up Type: cvbdm |
| 0373 |  | 1-3/4 x 3/4 | Moulding 26/01...T-36
$50 set up Type: doorm |
| 0392 |  | 1-3/4 x 5/8 | Moulding 27/03...T-34
$50 set up Type: doorm |
| 0402 |  | 1-3/4 x 1-5/8 | old fashioned full corner crown
Moulding 27/13...T-40
$60 set up Type: crwnm |
| 0406 |  | 1-3/4 x 5/8 | Moulding 27/17...T-31
$50 set up Type: chrrm |
| 0419 |  | 1-3/4 x 3/4 | dado can be varied
Moulding 29/04...T-20,26
as shown $95 set up Type: panlm |
| 0449 |  | 1-3/4 x 3/4 | Moulding 31/10...T-54
Beaded, symmetrical
$50 set up Type: casin |
| 0462 |  | 1-3/4 x 3/4 | old fashioned crown
Moulding 147/10...T-51
$95 set up Type: crwnm |
| 0501 |  | 1-3/4 x 1/2 | Moulding 33/01...T-49
$50 set up
symmetrical Type: doorm |
| 0502 |  | 1-3/4 x 3/4 | moulding 33/02...T-49
$50 set up Type: doorm |
| 0546 |  | 1-3/4+ x 7/16 | Moulding 35/07...T-50
$50 set-up Type: bbrdm |
| 0548 |  | 1-3/4 x 3/4 | typical brick mould
Moulding 35/09...T-50
$60 set up Type: miscm |
| 0624 |  | 1-3/4 x 1-1/8 | custom, high set-up...I have no idea what this was used for.
Moulding 145/05...T-47
Symmetrical
$125.00 set-up Type: miscm |
| 0652 |  | 1-3/4 x 1-1/2 | Moulding 40/05...T-62
$50 set up Type: crwnm |
| 0668 |  | 1-3/4 x 5/8 | Moulding 41/11...T-67
$50 set up
symmetrical Type: doorm |
| 0769 |  | 1-3/4 x 3/4 | Symmetrical
an be any width and thickness with the 4 beads located anywhere. Moulding 50/09...T-69
$60 set upBeaded
Type: doorm |
| 0805 |  | 1-3/4 x 5/8 | symmetrical
Moulding 47/05...T-
$50 set up Type: chrrm |
| 0819 |  | 1-3/4 x 1-5/16 | old fashioned pattern with full corner typically used as trim above exterior windows
Moulding 51/06...T-82
$60 set up
Type: crwnm |
| 0824 |  | 1-3/4 x 1/2 | old fashioned crown
Moulding 51/11...T-81
$95 set up Type: crwnm |
| 0928 |  | 1-3/4 x 1-1/4 | Moulding 59/08...T-91
$75 set up Type: doorm |
| 0936 |  | 1-3/4 x 1-3/4 | Moulding 60/03...T-90
add .30 per foot to run twice
Symmetrical
$75 set up Type: miscm |
| 1024 |  | 1-3/4 x 3/4 | dado can be spec'd
Moulding 40/16...T-
$75 set up Type: panlm |
| 1153 |  | 1-3/4 x 1-1/4 | dado can be spec'd
Moulding 74/15...T-106
$75 set up Type: panlm |
| 1216 |  | 1-3/4 x 1-3/8 | Moulding 80/07...T-120
$100 set up Type: miscm |
| 1247 |  | 1-3/4 x 13/16 | Moulding 82/12...T-113
$50 set up Type: doorm |
| 1365 |  | 1-3/4 x 3/4 | Moulding 90/12...T-128
$75 set up Type: cbntm |
| 1383 |  | 1-3/4 x 3/4 | Moulding 92/03...T-134
$50 set up Type: doorm |
| 1459 |  | 1-3/4 x 13/16 | Moulding 99/02...T-136
old style picture mould
$75 set up Type: miscm |
| 1471 |  | 1-3/4 x 3/4 | Moulding 99/14...T-130
$50 set up Type: doorm |
| 1552 |  | 1-3/4 x 1/2 | Moulding 105/13...T-14
$50 set up. For raised panels Type: panlm |
| 1560 |  | 1-3/4 x 13/16 | Moulding 106/08...T-148
please spec dado size
$75 set up Type: cbntm |
| 1597 |  | 1-3/4 x 3/4 | Moulding 109/10...T-154
$75 set up Type: casin |
| 1609 |  | 1-3/4 x 1-1/8 | Moulding 110/07...T-153
$75 set up Type: panlm |
| 1611 |  | 1-3/4 x 1-1/8 | Moulding 110/09...T-155
from 6/4"
$75 set up Type: cbntm |
| 1627 |  | 1-3/4+ x 3/4 | Moulding 111/11...T-157
$60 set up
Type: bbrdm |
| 1764 |  | 1-3/4 x 7/8 | Moulding 122/07...T-170
$50 set up Type: doorm |
| 1805 |  | 1-3/4 x 11/16 | Moulding 126/09...T-
$75 set up Type: cbntm |
| 1816 |  | 1-3/4 x 9/16 | Moulding 127/08...T-189
$95 set up
very close to our 1-3/4 bed Type: cvbdm |
| 1881 |  | 1-3/4 x 13/16 | Moulding 132/15...T-184
$75 set up
specify your dado dimensions Type: panlm |
| 1897 |  | 1-3/4 x 1-3/8 | Moulding 134/03...T-82,23
$75 set up Type: miscm |
| 1908 |  | 1-3/4 x 9/16 | Moulding 134/14...T-188
$95 set up
used on inside perimeter of raised panel doors Type: panlm |
| 1938 |  | 1-3/4 x 15/16 | Moulding 136/13...T-178
$50 set up Type: doorm |
| 1967 |  | 1-3/4 x 11/16 | Moulding 138/05...T-177
$50 set up Type: doorm |
| 1984 |  | 1-3/4 x 13/16 | Moulding 139/11...T-185
$60 set up Type: doorm |
| 2042 |  | 1-3/4 x 13/16 | Moulding 153/08...T-197
$50 set up as shown. can have dado for insert panel ad $25 Type: cbntm |
| 2106 |  | 1-3/4 x 3/4 | Moulding 158/07...T-202,174
$75 set up
Type: panlm |
| 2117 |  | 1-3/4 x 1-1/4 | Moulding 159/05...T-203
$50 set up Type: chrrm |
| 0133 |  | 1-13/16 x 3/4 | smaller section of the four beaded casing
Moulding 12/01...T-2
symmetrical
$50 set up Type: casin |
| 0138 |  | 1-13/16 x 3/4 | used on plywood with an offset of 1/2" to 3/4". Not the stock PM6
Moulding 12/05...T-11
$75 set up Type: panlm |
| 0327 |  | 1-13/16 x 1-1/2 | Moulding 149/09...T-29
$50 set up Type: doorm |
| 0364 |  | 1-13/16 x 1-1/4 | Moulding 25/10...T-41
$50 set up Type: doorm |
| 0529 |  | 1-13/16 x 13/16 | Moulding 34/07...T-56
$50 set up Type: chrrm |
| 1291 |  | 1-13/16 x 1-1/16 | Moulding 85/11...T-118
$75 set up Type: panlm |
| 1511 |  | 1-13/16 x 1-5/8 | Moulding 102/07...T-146
$75 set up Type: chrrm |
| 2067 |  | 1-13/16 x 3/4 | Moulding 155/06...T-195,138
another old style picture mould
$75 set up Type: miscm |
| 0084 |  | 1-7/8 x 1-1/4 | this was used as a bumper rail for a boat maker
Symmetrical
Moulding 07/04...T-1
$75 set up
Type: miscm |
| 0103 |  | 1-7/8 x 9/16 | aka cochran molding
3/4" off set
Moulding 09/04...T-125
$75 set up Type: panlm |
| 0173 |  | 1-7/8 x 1/2 | Moulding 11/03...T-9, 45`
Two knife set-up...$95 Type: bbrdm |
| 0275 |  | 1-7/8 x 7/8 | Moulding 147/07...T-24
$50 set up Type: doorm |
| 0421 |  | 1-7/8 x 1-1/4 | Moulding 29/05...T-51
$60 set up Type: casin |
| 0428 |  | 1-7/8 x 7/8 | Moulding 29/07...T-27
$50 set up Type: doorm |
| 0447 |  | 1-7/8 x 7/8 | Moulding 31/09...T-54
$75 set up Type: cbntm |
| 0563 |  | 1-7/8 x 1 | This is an old style picture mould.
Moulding 143/12...T-53
$75 set up Type: miscm |
| 0598 |  | 1-7/8 x 3/4 | Moulding 37/09
$50 set up Type: chrrm |
| 0606 |  | 1-7/8 x 1-1/8 | Moulding 148/09...T-
$50 set up Type: custo |
| 0809 |  | 1-7/8 x 7/8 | Moulding 47/09...T-71
$50 set up Type: doorm |
| 0940 |  | 1-7/8 x 5/8 | aka cochran moulding
Moulding 60/07...T-87
$95 set up Type: panlm |
| 0986 |  | 1-7/8 x 3/4 | symmetrical
Moulding 63/09...T-92
$95 set up Type: crwnm |
| 1010 |  | 1-7/8 x 1-1/4 | Moulding 65/06...T-92
$50 set up Type: doorm |
| 1168 |  | 1-7/8 x 1/2 | Type: panlm |
| 1208 |  | 1-7/8 x 3/4 | Moulding 79/15...T-123
$50 set up Type: casin |
| 1230 |  | 1-7/8 x 3/4 | Moulding 81/09...T-112
$95 set up Type: panlm |
| 1259 |  | 1-7/8 x 1-1/2 | Moulding 83/05...T-116
$95 set up Type: cbntm |
| 1470 |  | 1-7/8 x 11/16 | Moulding 99/13...T-129
$75 set up
cochran moulding Type: panlm |
| 1614 |  | 1-7/8 x 5/8 | Moulding 110/12...T-155
$75 set up
cochran moulding Type: panlm |
| 1647 |  | 1-7/8 x 1-1/8 | Moulding 113/09...T-158
$75 set up Type: panlm |
| 1658 |  | 1-7/8 x 3/4 | Moulding 114/08...T-158 Type: panlm |
| 1661 |  | 1-7/8 x 3/4 | Moulding 114/11...T-160 Type: doorm |
| 1760 |  | 1-7/8 x 3/4 | Moulding 122/03...T-170
$50 set up Type: doorm |
| 1837 |  | 1-7/8 x 3/4 | Moulding 129/07...T-19
$75 set up
similar to PM-6 Type: panlm |
| 1935 |  | 1-7/8 x 13/16 | Moulding 136/10...T-174
$75 set up
this is shown with no dado for panels. Type: cbntm |
| 1983 |  | 1-7/8 x 13/16 | Moulding 139/10...T-186
$60 set up Type: doorm |
| 2084 |  | 1-7/8 x 11/16 | Moulding 156/11...T-201
$60 set up
add $20 for dado Type: casin |
| 2085 |  | 1-7/8 x 11/16 | Moulding 156/12...T-201
$95 set up Type: panlm |
| 1123 |  | 1-15/16 x 13/16 | Moulding 76/09...T-96
$95 set up Type: doorm |
| 1584 |  | 1-15/16 x 1-1/4 | Moulding 108/08...T-151
$95 set up
cochran moulding Type: panlm |
| 1879 |  | 1-15/16 x 1-1/8 | Moulding 132/13...T-186
$95 set up
specify your dado dimensions Type: panlm |
| 2043 |  | 1-15/16 x 3/4 | Moulding 153/09...T-197
$50 set up Type: chrrm |
| 0029 |  | 2 x 1-1/2+ | symmetrical, Beaded
Moulding 01/10...T-19
$50 set up Type: chrrm |
| 0061 |  | 2 x 3/4 | aka boren moulding
05/01...T-2
$50 set up Type: chrrm |
| 0087 |  | 2+ x 3/4 | top portion shown in detail...can be any height
Moulding 06/09...T-15
$60 set-up Type: bbrdm |
| 0094 |  | 2 x 1-1/4 | aka 2" bullnose...1-1/4" tall.
tall two inch half round
Moulding 07/09...T-1
$50 set up
Symmetrical
This is the same knife used for a 2" half round; $50 set up Type: crndm |
| 0118 |  | 2 x 1/2 | 2" radius
Moulding 08/08...T-6
$50 set up
symmetrical Type: crndm |
| 0176 |  | 2 x 3/4 | Moulding 11/06...T-10
$50 set up
PM-6 without the bottom knife
Type: chrrm |
| 0170 |  | 2 x 1-15/16 | wall rail or banister cap, dado can be specified
Moulding 13/11...T-19
$110 set up
symmetrical Type: hrail |
| 0217 |  | 2 x 1-1/2 | dado can vary in size
Moulding 16/10...T-38
$95 set up Type: panlm |
| 0247 |  | 2 x 1 | Symmetrical
Moulding 18/11
aka DM1
$50 set up Type: doorm |
| 0254 |  | 2 x 13/16 | custom lip mold
Moulding 150/09...T-42
aka LSCM12
$75 set up Type: cbntm |
| 0289 |  | 2+ x 3/4 | Moulding 146/06...T-35
$60 set-up Type: bbrdm |
| 0294 |  | 2 x 13/16 | dado can be varied, double beaded
Moulding 21/02...T-31
$95 set up Type: cbntm |
| 0315 |  | 2 x 11/16 | Moulding 22/07...T-31
$95 set up
This angle may have been changed. Recommend bring sample. Type: panlm |
| 0334 |  | 2 x 7/8 | panel cap...dado can be varied.
Moulding 23/05...T-29
$95 set up Type: panlm |
| 0368 |  | 2 x 1-1/16 | Moulding 25/14...T-30
$50 set up Type: doorm |
| 0380 |  | 2 x 1-1/2 | Moulding 143/09...T-43
$50 set up Type: chrrm |
| 0399 |  | 2 x 3/4 | not a true half round
symmetrical
Moulding 27/10...T-34
$50 set up Type: crndm |
| 0435 |  | 2 x 9/16 | Moulding 31/01...T-27
aka LSCR1
$50 set up Type: chrrm |
| 0441 |  | 2 x 1-1/2 | Moulding 146/05...T-27
$50 set up Type: doorm |
| 0454 |  | 2 x 3/4 | aka LSCR3
Moulding 31/14...T-54
aka LSCR3
$50 set up Type: chrrm |
| 0458 |  | 2+ x 5/8 | Moulding 31/16...T-5
$60 set-up Type: bbrdm |
| 0459 |  | 2 x 5/8 | Moulding 31/17...T-34
$50 set up Type: casin |
| 0460 |  | 2 x 5/8 | Moulding 144/05...T-49
$60 set up, add $20 for dado Type: casin |
| 0461 |  | 2 x 11/16 | Similar to Bison DP
Moulding 30/05...T-49
$50 set up Type: doorm |
| 0464 |  | 2 x 1+ | 2-1/8" radius, thickness can be varied
Moulding 30/07...T-49
Symmetrical
$50 set up Type: crndm |
| 0476 |  | 2 x 1-1/16 | Moulding 141/06...T-51
$50 set up Type: chrrm |
| 0564 |  | 2 x 7/8 | Moulding 145/04...T-52
$50 set up Type: miscm |
| 0566 |  | 2+ x 3/4 | Moulding 142/03...T-53
$60 set-up Type: bbrdm |
| 0615 |  | 2 x 1-1/16 | large inside corner
Moulding 38/08...T-60
$85 set up Type: crndm |
| 0616 |  | 2+ x 1 | Moulding 38/09...T-58
$60 set up Type: doorm |
| 0651 |  | 2 x 7/8 | Moulding 40/04...T-62
$60 set up Type: casin |
| 0654 |  | 2+ x 1-1/4 | Moulding 40/07...T-60
$50 set up Type: doorm |
| 0670 |  | 2 x 1-1/2+ | Moulding 41/13...T-65
$50 set up Type: miscm |
| 0688 |  | 2+ x 3/4 | symmetrical
Moulding 42/08...T-65
$75 set up....Add $.30/lf for running twice Type: chrrm |
| 0708 |  | 2 x 11/16 | Symmetrical
Moulding 44/01...T-67
$50 set up Type: doorm |
| 0728 |  | 2 x 1-1/4 | Small beaded brick mould
Moulding 48/07...T-
$50 set up Type: miscm |
| 0729 |  | 2 x 3/4 | Moulding 48/08...T-75
$50 set up Type: chrrm |
| 0768 |  | 2 x 1-5/16 | notch can be spec'd
Moulding 50/08...T-69
$75 set up Type: panlm |
| 0770 |  | 2 x 9/16 | this is smaller than the colonial casing we stock. This is only 2" wide
Moulding 50/10...T-73
$50 set up
Type: casin |
| 0798 |  | 2 x 3/4 | simmulates a raised panel for a door
Moulding 46/11...T-65
$50 set up Type: cbntm |
| 0808 |  | 2 x 3/4 | Moulding 47/08...T-71
$50 set up Type: panlm |
| 0821 |  | 2 x 7/8 | Mitered cabinet door mould
Dado is for inserting panel.
Moulding 51/08...T-82
$75 set up Type: cbntm |
| 0849 |  | 2 x 1-1/16 | 3/4" offset shown
Moulding 53/06...T-84
$75 set up Type: panlm |
| 0852 |  | 2+ x 3/4 | Moulding 53/09...T-81
$60 set up Type: bbrdm |
| 0918 |  | 2+ x 9/16 | used as a cradle for a two piece crown assembly
Moulding 58/11...T-88
$60 set up Type: crwnm |
| 0938 |  | 2 x 1-1/2 | large lip mould that covers the edge of 3/4" plywood door panels
Moulding 60/05...T-89
$75 set up Type: cbntm |
| 0939 |  | 2 x 1-1/16 | Moulding 60/06...T-86
$50 set up Type: doorm |
| 0954 |  | 2+ x 1-5/16 | full cornered crown
Moulding 61/03...T-90
$60 set up Type: crwnm |
| 1023 |  | 2 x 3/4 | Sometimes with dado....add $25 to set up
Moulding 40/15...T-59
$50 set up Type: casin |
| 1028 |  | 2 x 1-7/8 | any dados, anywhere can be done
Moulding 143/03...T-
$75 set up Type: miscm |
| 1061 |  | 2 x 3/4 | Moulding 70/02...T-109
$50 set up Type: casin |
| 1063 |  | 2 x 9/16 | Moulding 70/04...T-102
$50 set up Type: casin |
| 1064 |  | 2 x 9/16 | Moulding 70/05...T-103
$50 set up
add $20 for dado Type: casin |
| 1116 |  | 2 x 1-13/16 | this is an oval, very subtle
Moulding 76/02...T-104
$120 set up
symmetrical Type: hrail |
| 1119 |  | 2 x 1-3/8 | Moulding 76/05...T-108
$75 set up Type: crwnm |
| 1157 |  | 2 x 3/4 | Be sure to spec gap dimension, beaded
Moulding 75/04...T-103
$75 set up Type: cbntm |
| 1175 |  | 2 x 3/4 | Symmetrical
Moulding 77/07...T-123
$50 set up Type: chrrm |
| 1187 |  | 2 x 13/16 | Beaded cabinet door frame shown w/out dado for panel or glass
Moulding 78/07...T-126
$50 set up
Add $25 for dado Type: cbntm |
| 1199 |  | 2 x 13/16 | Moulding 79/07...T-101,127
$95 set up Type: panlm |
| 1217 |  | 2 x 1-3/8 | Moulding 80/08...T-120
$95 set up Type: miscm |
| 1239 |  | 2 x 3/4 | Moulding 82/04...T-116
one bead
$60 set up Type: casin |
| 1257 |  | 2+ x 5/8 | Moulding 83/03...T-112
$60 set up Type: bbrdm |
| 1294 |  | 2 x 1 | Moulding 85/14...T-119
$75 set up, $50 without dado Type: chrrm |
| 1301 |  | 2 x 13/16 | Moulding 86/07...T-119
$50 set up Type: doorm |
| 1302 |  | 2 x 3/4 | Symmetrical
Moulding 86/08...T-118
$50 set up Type: doorm |
| 1319 |  | 2 x 3/4 | Moulding 87/06...T-140
symmetrical
$50 set up Type: doorm |
| 1325 |  | 2 x 3/4 | Moulding 87/12...T-133
$50 set up Type: casin |
| 1330 |  | 2 x 11/16 | Moulding 87/17...T-131
$50 set up Type: casin |
| 1355 |  | 2 x 1/2 | Moulding 90/02...T-142
symmetrical
$50 set up Type: casin |
| 1357 |  | 2 x 1-1/4 | Moulding 90/04...T-135
$95 set up Type: panlm |
| 1361 |  | 2 x 1-3/4 | Moulding 90/08...T-128
$50 set up Type: doorm |
| 1384 |  | 2 x 13/16 | Moulding 92/04...T-139
$75 set up Type: cbntm |
| 1402 |  | 2+ x 3/4 | Moulding 92/22...T-114
$60 set up Type: bbrdm |
| 1457 |  | 2 x 2 | Moulding 98/12...T-85
$50 set up Type: doorm |
| 1479 |  | 2 x 5/8 | Moulding 99/21...T-143
$50 set up Type: chrrm |
| 1497 |  | 2 x 5/8 | Moulding 101/07...T-145
$50 set up Type: chrrm |
| 1500 |  | 2 x 7/16 | Moulding 101/10...T-145
$75 set up Type: panlm |
| 1509 |  | 2 x 1-1/16 | Moulding 102/05...T-1
$110 set up
symmetrical Type: hrail |
| 1512 |  | 2 x 1-1/2 | Moulding 102/08...T-143
$80 set up Type: miscm |
| 1531 |  | 2 x 3/4 | Moulding 104/04...T-148
$50 set up Type: chrrm |
| 1548 |  | 2 x 3/4 | Moulding 105/09...T-149
$50 set up Type: casin |
| 1583 |  | 2 x 13/16 | Moulding 108/07...T-151
$75 set up Type: cbntm |
| 1594 |  | 2 x 1 | Moulding 109/07...T-153
$50 set up Type: chrrm |
| 1610 |  | 2 x 3/4 | Moulding 110/08...T-154
$75 set up Type: cbntm |
| 1691 |  | 2 x 3/4 | Moulding 116/13...T-163 Type: panlm |
| 1709 |  | 2 x 3/4 | Moulding 118/04...T-164
$95 set up
spec dado size Type: cbntm |
| 1710 |  | 2 x 3/4 | Moulding 118/05...T-165
$95 set up
spec dado size Type: cbntm |
| 1761 |  | 2 x 3/4 | Moulding 122/04...T-171
$50 set up Type: doorm |
| 1828 |  | 2 x 7/8 | Moulding 128/09...T-176
$85 set up
spec panel dado size Type: cbntm |
| 1838 |  | 2 x 3/4 | Moulding 129/08...T-181
$50 set up Type: casin |
| 1856 |  | 2 x 1 | Moudling 130/12...T-180
$50 set up Type: crwnm |
| 1880 |  | 2 x 1-1/16 | Moulding 132/14...T-184
$75 set up Type: panlm |
| 1933 |  | 2 x 3/4 | Moulding 136/08...T-183
$95 set up Type: cbntm |
| 1934 |  | 2 x 13/16 | Moulding 136/09...T-175
$80 set up Type: cbntm |
| 1943 |  | 2 x 15/16 | Moulding 136/18...T-46,192
$95 set up Type: crndm |
| 1956 |  | 2 x 3/4 | Moulding 137/12...T-174
$95 set up Type: panlm |
| 1958 |  | 2 x 1/2 | Moulding 137/14...T-174
$50 set up Type: doorm |
| 1995 |  | 2 x 15/16 | Moulding 161/07...T-205
$75 set up Type: panlm |
| 1996 |  | 2 x 3/4 | Moulding 161/08...T-205
$75 set up Type: panlm |
| 2051 |  | 2 x 3/4 | Moulding 154/05...T-193
$85 set up
Type: cbntm |
| 2052 |  | 2 x 1-1/16 | Moulding 154/06...T-194
$50 set up Type: crndm |
| 2068 |  | 2 x 1-1/2 | Moulding 155/07...T-194
$50 set up Type: miscm |
| 2081 |  | 2 x 3/4 | Moulding 156/08...T-198
$50 set up Type: chrrm |
| 2096 |  | 2 x 1-13/16 | Moulding 157/06...T-200
$60 set up Type: crwnm |
| 1160 |  | 2-1/16 x 3/4 | Spec gap dimension, beaded
Moulding 75/06...T-104
$75 set up Type: cbntm |
| 0164 |  | 2-1/8 x 7/8 | 3/4" off set
Moulding 13/05...T-18
$95 set up Type: panlm |
| 0189 |  | 2-1/8 x 1-1/4 | Moulding 14/05...T-16
$50 set up Type: chrrm |
| 0191 |  | 2-1/8 x 15/16 | Moulding 14/07...T-45
$50 set up Type: doorm |
| 0203 |  | 2-1/8 x 5/8 | Moulding 149/10...T-23
set up $95 Type: crwnm |
| 0255 |  | 2-1/8 x 1-1/4 | Moulding 150/10
$50 set up Type: chrrm |
| 0363 |  | 2-1/8 x 1 | dado can vary in size
Moulding 25/09...T-30
$75 set up Type: panlm |
| 0365 |  | 2-1/8 x 7/8 | Beaded cabinet door lip mould
Moulding 25/11...T-26
$75 set up Type: cbntm |
| 0376 |  | 2-1/8 x 1 | Moulding 26/03...T-36
$50 set up Type: chrrm |
| 0496 |  | 2-1/8+ x 1-1/2 | used as an edge around a piece of plywood to make a table top
Moulding 143/05...T-43
$95 set up
Type: crndm |
| 0530 |  | 2-1/8 x 1-3/16 | Moulding 34/08...T-39, T-49
$95 set up
symmetrical Type: hrail |
| 0579 |  | 2-1/8 x 3/4 | Moulding 36/10...T-50
$75 set up
beaded Type: custo |
| 0584 |  | 2-1/8 x 11/16 | symmetrical
Moulding 36/15...T-56
$95 set up Type: crwnm |
| 0604 |  | 2-1/8 x 13/16 | Moulding 143/10...T-
$75 set up Type: custo |
| 0705 |  | 2-1/8 x 3/4 | Moulding 147/09...T-61
$50 set up Type: chrrm |
| 0999 |  | 2-1/8 x 1-3/8 | Moulding 64/09...T-23
$60 set up Type: crwnm |
| 1003 |  | 2-1/8 x 9/16 | symmetrical
Moulding 64/13...T-94
$95 set up Type: cvbdm |
| 1048 |  | 2-1/8 x 9/16 | bed
Moulding 68/12...T-109
$95 set up Type: cvbdm |
| 1062 |  | 2-1/8 x 3/4 | Moulding 70/03...T-108
$50 set up Type: casin |
| 1279 |  | 2-1/8 x 1-7/8 | Moulding 84/10...T-
Symmetrical
$75 set up Type: miscm |
| 1285 |  | 2-1/8 x 5/8 | Moulding 85/05...T-119
$50 set up Type: casin |
| 1328 |  | 2-1/8 x 11/16 | Moulding 87/15...T-133
$50 set up Type: casin |
| 1358 |  | 2-1/8 x 13/16 | Moulding 90/05...T-135
$50 set up
symmetrical beaded Type: casin |
| 1360 |  | 2-1/8 x 3/4 | Moulding 90/07...T-134
$50 set up Type: chrrm |
| 1534 |  | 2-1/8 x 5/8 | Moulding 104/07...T-146
$95 set up Type: cvbdm |
| 1643 |  | 2-1/8 x 1-1/2 | Moulding 113/05...T-156
$75 set up Type: panlm |
| 1731 |  | 2-1/8 x 1-1/16 | Moulding 119/12...T-167,54
$95 set up Type: cbntm |
| 1815 |  | 2-1/8 x 3/4 | Moulding 127/07...T-193
$95 set up Type: crwnm |
| 1835 |  | 2-1/8 x 15/16 | Moulding 129/05...T-193
$75 set up Type: panlm |
| 1853 |  | 2-1/8 x 1-1/2 | Moulding 130/09...T-180
$95 set up Type: miscm |
| 1912 |  | 2-1/8+ x 9/16 | Moulding 135/02...T-176
$60 set up Type: doorm |
| 1914 |  | 2-1/8 x 5/8 | Moulding 135/03...T-180
$50 set up Type: casin |
| 2009 |  | 2-1/8 x 5/8 | Moulding 162/08...T-206
$50 set up Type: casin |
| 0503 |  | 2-3/16 x 3/4 | Moulding 33/03...T-57
$75 set up Type: chrrm |
| 1162 |  | 2-3/16 x 13/16 | Specify gap dimension, beaded
Moulding 75/08...T-104
$75 set up Type: cbntm |
| 1694 |  | 2-3/16 x 9/16 | Moulding 116/16...T-163
$95 set up Type: crwnm |
| 0027 |  | 2-1/4+ x 3/4 | Moulding 01/08...T-19
$60 set-up Type: bbrdm |
| 0056 |  | 2-1/4 x 3/4 | Moulding 04/05...T-5
$75 set up, $50 without relief Type: casin |
| 0081 |  | 2-1/4 x 3/4 | Moulding 06/06...T-45
$75 set up Type: panlm |
| 0120 |  | 2-1/4 x 11/16 | aka LSC346
Moulding 10/02...T-23
$60 set up Type: casin |
| 0128 |  | 2-1/4 x 1-1/16 | dado can be changed
Moulding 10/08...T-14
$75 set up Type: panlm |
| 0233 |  | 2-1/4 x 5/8 | Moulding 18/04...T-26
$50 set up Type: casin |
| 0240 |  | 2-1/4 x 3/4 | Beaded cabinet door frame pattern. Please spec gap dimension.
Moulding 143/08...T-26
$75 set up Type: cbntm |
| 0282 |  | 2-1/4 x 11/16 | old fashioned crown mould, typically found in older homes
Moulding 141/10...T-24
$95 set up Type: crwnm |
| 0283 |  | 2-1/4 x 3/4 | Beaded cabinet door frame pattern. Please spec gap dimension.
Moulding 19/21...T-26
$95 set up (note the beveled back) Type: cbntm |
| 0292 |  | 2-1/4 x 11/16 | Moulding 148/04...T-25
$50 set up Type: chrrm |
| 0298 |  | 2-1/4 x 3/4 | Moulding 21/06...T-37
$95 set up
symmetrical Type: cvbdm |
| 0371 |  | 2-1/4 x 3/4 | Moulding 150/06...T-41
beaded symmetrical
$50 set up Type: casin |
| 0489 |  | 2-1/4 x 7/8 | used for cabinet door frame material. Please spec the gap dimension.
Moulding 32/08...T-57
$75 set up Type: cbntm |
| 0497 |  | 2-1/4 x 3/4 | 2-1/4 crown with no angles cut
Moulding 140/07...T-49
$50 set up Type: crwnm |
| 0504 |  | 2-1/4 x 3/4 | symmetrical
Moulding 33/04...T-49
$75 set up Type: chrrm |
| 0541 |  | 2-1/4 x 13/16 | Moulding 35/02...T-50
Set up $95
Type: crwnm |
| 0576 |  | 2-1/4 x 1-3/4 | dados can be adjusted.
can be used as a cradle
Moulding 36/07...T-50
$75 set up Type: crwnm |
| 0686 |  | 2-1/4 x 11/16 | Moulding 42/06...T-63
$60 set up Type: casin |
| 0725 |  | 2-1/4 x 13/16 | dado can be any spec'd size
Moulding 48/04...T-71
$75 set up Type: cbntm |
| 0727 |  | 2-1/4 x 7/8 | Moulding 48/06...T-74
$50 set up Type: chrrm |
| 0804 |  | 2-1/4 x 5/8 | this can have a rope inserted in the groove
Moulding 47/04...T-70
$50 set up Type: chrrm |
| 0857 |  | 2-1/4 x 9/16 | Moulding 53/14...T-78
$50 set up Type: casin |
| 0960 |  | 2-1/4 x 2 | Moulding 61/09...T-87
$50 set up Type: crwnm |
| 0962 |  | 2-1/4 x 1 | Moulding 61/11...T-86
$60 set up Type: miscm |
| 0997 |  | 2-1/4 x 1-3/4 | Moulding 64/07...T-misc.
$110 set up, can specify dado, etc. Type: thrsm |
| 1004 |  | 2-1/4 x 3/4 | Moulding 64/14...T-92
$95 set up Type: cvbdm |
| 1007 |  | 2-1/4 x 1-5/16 | Moulding 65/03...T-49, T-93
$120 set up, add $.30 per foot to run two passes
symmetrical Type: hrail |
| 1021 |  | 2-1/4 x 5/16 | Moulding 36/12...T-50
$95 set up Type: miscm |
| 1027 |  | 2-1/4 x 2-1/8 | Moulding 150/04...T-
set up $110, add .30/lf for running twice
symmetrical Type: hrail |
| 1038 |  | 2-1/4 x 2-1/4 | solid full crown, measures as a typical 3-1/4" crown
Moulding 68/02...T-98
$130 set up; 5 knives Type: crwnm |
| 1042 |  | 2-1/4 x 1-1/2 | Moulding 68/06...T-110
$50 set up Type: crwnm |
| 1073 |  | 2-1/4+ x 9/16 | Moulding 70/14...T-111
$60 set up Type: bbrdm |
| 1148 |  | 2-1/4 x 9/16 | Symmetrical
Moulding 74/10...T-111
$50 set up, add .30 to run twice Type: panlm |
| 1149 |  | 2-1/4 x 5/8 | 3/4" offset
Moulding 74/11...T-110
$75 set up Type: panlm |
| 1161 |  | 2-1/4 x 3/4 | Specify gap dimension, beaded
Moulding 75/07...T-105
$75 set up Type: cbntm |
| 1164 |  | 2-1/4 x 7/8 | Specify tab dimensions
Moulding 75/10...T-105
$75 set up Type: panlm |
| 1292 |  | 2-1/4+ x 3/4 | Moulding 85/12...T-
Known as a beveled edge. 'Beveling' or 'Champhering' assumes a 45 degree angular cut
$50 set up
Type: bbrdm |
| 1324 |  | 2-1/4 x 5/8 | Moulding 87/11...T-141
$50 set up Type: casin |
| 1341 |  | 2-1/4 x 3/4 | Moulding 88/11...T-133
$75 set up with dado
please spec dado size Type: chrrm |
| 1359 |  | 2-1/4 x 3/4 | Moulding 90/06...T-131
$75 set up Type: panlm |
| 1469 |  | 2-1/4 x 13/16 | Moulding 99/12...T-?
$75 set up Type: panlm |
| 1487 |  | 2-1/4 x 1-1/4 | Moulding 100/07...T-143
$60 set up Type: crwnm |
| 1499 |  | 2-1/4 x 1-1/4 | Moulding 101/09...T-144
$60 set up Type: chrrm |
| 1503 |  | 2-1/4 x 1-1/16 | Moulding 101/13...T-144
$75 set up Type: cbntm |
| 1507 |  | 2-1/4 x 2-1/8 | Moulding 102/03...T-143
$50 set up Type: chrrm |
| 1547 |  | 2-1/4 x 3/4 | Moulding 105/08...T-149
$50 set up
$75 set up with relief Type: casin |
| 1568 |  | 2-1/4 x 1-1/16 | Moulding 107/05...T-152
$60 set up Type: chrrm |
| 1580 |  | 2-1/4 x 5/8 | Moulding 108/04...T-151
$50 set up Type: casin |
| 1592 |  | 2-1/4 x 1 | Moulding 109/05...T-153
$60 set up Type: crwnm |
| 1593 |  | 2-1/4 x 5/8 | Moulding 109/06...T-154
$60 set up Type: casin |
| 1607 |  | 2-1/4 x 1-7/16 | Moulding 110/05...T-156
$60 set up Type: crndm |
| 1625 |  | 2-1/4 x 13/16 | Moulding 111/09...T-156
$75 set up
You can add dado for panel on left side +$25 Type: cbntm |
| 1670 |  | 2-1/4 x 5/8 | Moulding 115/03...T-161
$50 set up Type: casin |
| 1686 |  | 2-1/4 x 1-15/16 | Moulding 116/08...T-162
$50 set up Type: panlm |
| 1716 |  | 2-1/4 x 5/8 | Moulding 118/11...T-164
$60 set up
Symmetrical Type: chrrm |
| 1752 |  | 2-1/4 x 3/4 | Moulding 121/08...T-169
$50 set up
$75 set up with relief Type: casin |
| 1836 |  | 2-1/4 x 1-3/8 | Moulding 129/06...T-180
$75 set up Type: panlm |
| 1840 |  | 2-1/4 x 3/4 | Moulding 129/10...T-179
$50 set up Type: chrrm |
| 1878 |  | 2-1/4 x 1-1/16 | Moulding 132/12...T-184
$50 set up Type: chrrm |
| 1991 |  | 2-1/4 x 1-13/16 | Moulding 161/03...T-203
$60 set up Type: crwnm |
| 1993 |  | 2-1/4 x 3/4 | Moulding 161/05...T-204
$95 set up Type: panlm |
| 2000 |  | 2-1/4 x 3/4 | Moulding 161/12...T-204
symmetrical island or cabinet corner treatment
$95 set up Type: cbntm |
| 2010 |  | 2-1/4 x 1-5/16 | Moulding 162/09...T-206
$75 set up Type: panlm |
| 2015 |  | 2-1/4 x 1-1/16 | Moulding 151/03...T-45
$75 set up
specify dado dimensions Type: panlm |
| 2023 |  | 2-1/4 x 3/4 | Moulding 151/11...T-196
$75 set up Type: chrrm |
| 2089 |  | 2-1/4 x 1-1/4 | Moulding 156/16...T-200
$95 set up Type: cbntm |
| 2118 |  | 2-1/4 x 1-3/8 | Moulding 159/06...T-203
$85 set up Type: panlm |
| 0070 |  | 2-5/16 x 11/16 | aka wedge casing.
Moulding 05/11...T-16
$75 set up, $50 w/out relief
aka LSC2 Type: casin |
| 0404 |  | 2-5/16 x 3/4 | Beaded cabinet door frame pattern. Please spec gap dimension.
Moulding 27/15...T-41
$75 set up
Type: cbntm |
| 0145 |  | 2-3/8 x 7/8 | used as cabinet door frames
Moulding 12/11...T-44
$75 set up shown w/out dado for panel...too small for 1/4" dado for panel Type: cbntm |
| 0207 |  | 2-3/8 x 1-3/4+ | a style of handrail used between newel posts and spindles below
Moulding 16/04...T-23
add .30 to run twice, set up $75
symmetrical Type: hrail |
| 0335 |  | 2-3/8 x 1 | used to make cabinet door frames...shown without 1/4" dado for panel
Moulding 23/06...T-28
$50 set up as shown...add $25 with dado
Type: cbntm |
| 0379 |  | 2-3/8 x 3/4 | cabinet door frame pattern. Please spec gap dimension.
Moulding 26/06...T-36
$95 set up Type: cbntm |
| 0500 |  | 2-3/8+ x 3/4 | this is an enlarged PM-5
Moulding 142/06...T-2
Two knife set-up...$75
Type: bbrdm |
| 0560 |  | 2-3/8 x 13/16 | Moulding 35/14...T-50
Beaded
$50 set up Type: chrrm |
| 0655 |  | 2-3/8 x 11/16 | tab size can be spec'd
Moulding 40/08...T-
$75 set up Type: panlm |
| 0674 |  | 2-3/8 x 13/16 | Moulding 41/17...T
$105 set up Type: crwnm |
| 0822 |  | 2-3/8 x 7/8 | Mitered cabinet door frames pattern and panel inserted in slot
Moulding 51/09...T-82
$75 set up Type: cbntm |
| 0908 |  | 2-3/8 x 3/4 | dado can be spec'd
Moulding 58/03...T-88
$75 set up Type: panlm |
| 1165 |  | 2-3/8 x 1-1/4 | Moulding 75/11...T-110,23
$75 set up Type: crndm |
| 1317 |  | 2-3/8 x 9/16 | Moulding 87/04...T-111
$50 set up Type: casin |
| 1386 |  | 2-3/8 x 13/16 | Moulding 92/06...T-138
$85 set up Type: cbntm |
| 1410 |  | 2-3/8 x 1-3/8 | Moulidng 93/08...T-136
$60 set up Type: crwnm |
| 1527 |  | 2-3/8 x 3/4 | Moulding 103/09...T-147
$50 set up
same knife can be used for brick mould Type: casin |
| 1530 |  | 2-3/8 x 3/4 | Moulding 104/03...T-147
$50 set up Type: casin |
| 1567 |  | 2-3/8 x 1-3/16 | Moulding 107/04...T-151
$50 set up Type: chrrm |
| 1575 |  | 2-3/8 x 1-1/4 | Moulding 107/12...T-152
$75 set up with cutout shown, $50 w/out cutout Type: chrrm |
| 1671 |  | 2-3/8 x 1-3/8 | Moulding 115/04...T-162
$60 set up Type: crwnm |
| 1747 |  | 2-3/8 x 1-13/16 | Moulding 121/03...T-170
$60 set up Type: doorm |
| 1855 |  | 2-3/8 x 1-1/8 | Moulding 130/11...T-181
$85 set up Type: crndm |
| 1920 |  | 2-3/8 x 7/8 | Moulding 135/09...T-178
$50 set up Type: chrrm |
| 1924 |  | 2-3/8 x 5/8 | Moulding 135/13...T-174
$95 set up Type: crwnm |
| 1939 |  | 2-3/8 x 1-3/16 | Moulding 136/14...T-177
$50 set up Type: doorm |
| 1999 |  | 2-3/8 x 5/8 | Moulding 161/11...T-204
$60 set up
symmetrical Type: casin |
| 2020 |  | 2-3/8 x 1-1/8 | Moulding 151/08...T-180
call for setup; different dados available
Type: miscm |
| 2078 |  | 2-3/8 x 7/8 | Moulding 156/05...T-199
another picture mould
$75 set up Type: miscm |
| 2123 |  | 2-3/8 x 1-1/4 | Moulding 159/11...T-200
$75 set up Type: panlm |
| 0851 |  | 2-7/16 x 13/16 | 3/4" offset shown
Moulding 53/08...T-79
$75 set up Type: panlm |
| 2066 |  | 2-7/16 x 1-3/4 | Moulding 155/05...T-197,192
$95 set up
note: not symmetrical Type: hrail |
| 0032 |  | 2-1/2 x 1-1/4 | aka a true 2-1/2" half round
symmetrical
Moulding 02/09...T-6
$50 set up
Type: crndm |
| 0040 |  | 2-1/2 x 3/4 | Moulding 02/01...T-17
$95 set up Type: crwnm |
| 0065 |  | 2-1/2 x 3/4 | Moulding 05/06...T-1
$75 set up
specify dado dimensions Type: chrrm |
| 0066 |  | 2-1/2 x 5/8 | aka c211 or b211...T-16
Moulding 05/07
$50 set up for 2-1/2 casing, $60 set up when it is wider than 2-1/2" (typically the base) Type: casin |
| 0067 |  | 2-1/2 x 3/4 | symmetrical
Moulding 05/08...T-1
$50 set up Type: chrrm |
| 0069 |  | 2-1/2 x 11/16 | two step casing
Moulding 05/10...T-10
$75 set up, $50 w/out relief Type: casin |
| 0129 |  | 2-1/2 x 1-7/16 | Moulding 10/09...T-14
$75 set up
Note left side is slanted. Type: chrrm |
| 0144 |  | 2-1/2 x 1-1/8 | symmetrical
Moulding 12/10...T-44
$95 set up or $50 with no dados Type: chrrm |
| 0154 |  | 2-1/2 x 3/4 | dado can be specified to any dimension.
symmetrical
Moulding 13/03...T-18
$75 set up Type: custo |
| 0177 |  | 2-1/2 x 1-1/4 | any chair rail can be made thicker and a notch put in to accept paneling or waincoat making it a panel cap like this one shown.
Moulding 11/07...T-8
$75 set up Type: chrrm |
| 0184 |  | 2-1/2 x 7/8 | Moulding 14/01...T-44
$50 set up Type: chrrm |
| 0198 |  | 2-1/2 x 11/16 | unusually plump casing
Moulding 14/13...T-21
$75 set up, $50 w/out relief Type: casin |
| 0218 |  | 2-1/2 x 3/4 | Moulding 16/11...T-38
$50 set up Type: casin |
| 0221 |  | 2-1/2 x 1 | Moulding 141/09...T-38
$75 set up Type: chrrm |
| 0234 |  | 2-1/2 x 5/8 | Moulding 17/08...T-23
beaded, symmetrical
$50 set up Type: casin |
| 0244 |  | 2-1/2 x 11/16 | Moulding 17/13...T-33
$60 set-up Type: bbrdm |
| 0287 |  | 2-1/2 x 3/4 | Moulding 149/07...T-31
$75 set up
beads, symmetrical Type: chrrm |
| 0290 |  | 2-1/2 x 13/16 | Moulding 150/11...T-31
$50 set up Type: chrrm |
| 0307 |  | 2-1/2 x 1-1/2 | this is a cradle mould...used with another for a compound molding
Moulding 144/04...T-25
$75 set up
Type: crwnm |
| 0311 |  | 2-1/2 x 2 | this was a custom moulding and duplication requires a $150.00 set-up fee
Moulding 22/02...T-38
$150 set up (two setups to do it)
Type: crwnm |
| 0313 |  | 2-1/2 x 3/4 | dado can be spec'd
Moulding 22/05...T-misc.
$95 set up Type: miscm |
| 0367 |  | 2-1/2 x 1-3/16 | Moulding 25/13...T-30
$50 set up Type: doorm |
| 0397 |  | 2-1/2 x 13/16 | Moulding 27/08...T-34
aka LSCR2
$50 set up Type: chrrm |
| 0403 |  | 2-1/2 x 15/16 | another door frame mld shown w/out dado for panel
Moulding 27/14...T-41
$50 set up as shown w/out dado for panel Type: cbntm |
| 0410 |  | 2-1/2 x 3/4 | can be used as a column simulation
Moulding 150/08...T-34
symmetrical, fluted cabinet corner
$50 set up
Type: casin |
| 0423 |  | 2-1/2 x 1 | Moulding 28/08...T-43
$50 set up Type: casin |
| 0437 |  | 2-1/2 x 5/8 | aka one step casing
Moulding 31/02...T-54
$75 set up, $50 without relief Type: casin |
| 0451 |  | 2-1/2 x 7/8 | Moulding 31/11...T-23
$50 set up Type: casin |
| 0452 |  | 2-1/2 x 13/16 | Moulding 31/12...T-20
$50 set up
add $20 for dado Type: casin |
| 0470 |  | 2-1/2 x 1-7/16 | dado can be spec'd
Moulding 30/09...T-54
$75 set up Type: panlm |
| 0484 |  | 2-1/2 x 1-1/4 | Moulding 32/03...T-49
$75 set up Type: chrrm |
| 0486 |  | 2-1/2 x 1-1/8 | dado can be spec'd
Moulding 32/05...T-49
$75 set up Type: panlm |
| 0487 |  | 2-1/2 x 1-1/16 | Stair nosing or starter piece..can have many different dimensions
Moulding 32/06...T-misc.
$95 set up Type: thrsm |
| 0491 |  | 2-1/2 x 3/4 | Moulding 32/10...T-
$95 set up Type: miscm |
| 0492 |  | 2-1/2 x 3/4 | Moulding 32/11...T-30
$75 set up Type: miscm |
| 0550 |  | 2-1/2+ x 3/4 | Moulding 35/11...T-56
$60 set up Type: bbrdm |
| 0575 |  | 2-1/2 x 1+ | Moulding 36/06...T-50
$50 set up Type: chrrm |
| 0586 |  | 2-1/2+ x 3/4+ | Moulding 144/03...T-56
$50 set up
beaded Type: custo |
| 0605 |  | 2-1/2 x 1-9/16 | a table perimeter mould
Moulding 150/12...T-
$75 set up Type: crndm |
| 0619 |  | 2-1/2 x 1 | Moulding 38/12...T-60
$60 set up
beaded Type: custo |
| 0629 |  | 2-1/2 x 5/8 | Moulding 39/05...T-55
$50 set up Type: casin |
| 0636 |  | 2-1/2 x 5/8+ | Moulding 39/12...T-58
$50 set up Type: casin |
| 0641 |  | 2-1/2 x 1/2 | contemporary casing
Moulding 142/09...T-61
$75 set up, $50 setup without relief Type: casin |
| 0666 |  | 2-1/2+ x 3/4+ | Moulding 41/09...T-
$70 set-up Type: custo |
| 0724 |  | 2-1/2 x 3/4 | used as a perimeter of a cabinet door
Moulding 48/03...T-72
shown $75 set up. add $25 for dado Type: cbntm |
| 0730 |  | 2-1/2 x 3/4 | Moulding 48/09...T-77
$50 set up Type: chrrm |
| 0731 |  | 2-1/2 x 3/4 | dado or offset can be any spec'd size; used as a cradle for crown
Moulding 48/10...T-76
$75 set up Type: crwnm |
| 0732 |  | 2-1/2 x 1-1/4 | Moulding 48/11...T-76
$50 set up Type: chrrm |
| 0738 |  | 2-1/2 x 1-3/4 | Moulding 49/04...T-75
$75 set up Type: cvbdm |
| 0771 |  | 2-1/2 x 11/16 | if we add a relief it will be $25 more
Moulding 50/11...T-75
$50 set up Type: casin |
| 0778 |  | 2-1/2 x 5/8 | Moulding 45/06...T-69
$50 set up Type: casin |
| 0780 |  | 2-1/2 x 5/8 | Moulding 45/08...T-22
$50 set up Type: casin |
| 0823 |  | 2-1/2 x 11/16 | Mitered cabinet door mould
Moulding 51/10...T-84
$85 set up Type: cbntm |
| 0856 |  | 2-1/2 x 5/8 | similar to ca-8
Moulding 53/13 T-85
$75 set up, $50 w/out relief Type: casin |
| 0862 |  | 2-1/2 x 5/8 | Symmetrical, beaded
Moulding 54/04...T-82
$75 set up Type: chrrm |
| 0869 |  | 2-1/2 x 1-1/2 | Moulding 54/11...T-81
$50 set up Type: chrrm |
| 0870 |  | 2-1/2 x 9/16 | Moulding 54/12...T-85
$50 set up Type: casin |
| 0917 |  | 2-1/2 x 11/16 | Moulding 58/10...T-88
$75 set up Type: casin |
| 0959 |  | 2-1/2 x 1 | Moulding 61/08...T-91
$50 set up Type: cbntm |
| 0980 |  | 2-1/2 x 3/4 | Moulding 63/03...T-94
$75 set up Type: custo |
| 1046 |  | 2-1/2 x 13/16 | Moulding 68/10...T-107
$110 set up Type: crwnm |
| 1056 |  | 2-1/2 x 3/4 | Moulding 69/08...T-96
$50 set up Type: casin |
| 1081 |  | 2-1/2+ x 7/8 | Moulding 71/08...T-103
$60 set up Type: bbrdm |
| 1101 |  | 2-1/2 x 3/4 | Moulding 73/08...T-98
symmetrical
$75 set up, must run twice, add $.30
Type: chrrm |
| 1114 |  | 2-1/2 x 11/16 | Moulding 66/09...T-98
$95 set up Type: crwnm |
| 1143 |  | 2-1/2 x 3/4 | Moulding 74/05...T-101
$50 set up Type: chrrm |
| 1145 |  | 2-1/2 x 5/8 | Moulding 74/07...T-103
$50 set up, add $20 for relief Type: chrrm |
| 1147 |  | 2-1/2 x 3/4 | Moulding 74/09...T-102
$60 set up Type: chrrm |
| 1154 |  | 2-1/2 x 1 | dado can be spec'd
Moulding 74/16...T-99
$75 set up Type: panlm |
| 1173 |  | 2-1/2 x 1-1/2 | Moulding 77/05...T-113
$50 set up Type: chrrm |
| 1174 |  | 2-1/2 x 13/16 | Moulding 77/06...T-126
$75 set up Type: chrrm |
| 1184 |  | 2-1/2 x 1-7/8 | Full piece bed moulding
Moulding 78/04...T-120
$60 set up
Fruit Type: cvbdm |
| 1194 |  | 2-1/2 x 13/16 | Spec gap dimension, double beaded
Moulding 79/03...T-122
$75 set up Type: cbntm |
| 1200 |  | 2-1/2 x 11/16 | Moulding 79/08...T-127
$50 set up Type: chrrm |
| 1219 |  | 2-1/2 x 1-3/16 | Moulding 80/10...T-121
$50 set up Type: chrrm |
| 1220 |  | 2-1/2 x 3/4 | Moulding 80/11...T-125
$80 set up Type: miscm |
| 1240 |  | 2-1/2 x 13/16 | Spec gap dimension, beaded
Moulding 82/05...T-115
$75 set up Type: cbntm |
| 1266 |  | 2-1/2 x 3/4 | Moulding 83/12...T-122
$95 set up Type: crwnm |
| 1323 |  | 2-1/2 x 5/8 | Moulding 87/10...T-136
$75 set up, $50 w/out relief Type: casin |
| 1327 |  | 2-1/2 x 11/16 | Moulding 87/14...T-139
$50 set up Type: casin |
| 1329 |  | 2-1/2 x 3/4 | Moulding 87/16...T-136
$50 set up Type: casin |
| 1353 |  | 2-1/2 x 1-1/4 | Moulding 89/11...T-138
$85 set up Type: chrrm |
| 1362 |  | 2-1/2 x 3/4 | Moulding 90/09...T-99
$75 set up, add .30 to run twice
symmetrical Type: chrrm |
| 1401 |  | 2-1/2 x 7/8 | Moulding 92/21...T-128
$75 set up Type: panlm |
| 1409 |  | 2-1/2 x 1-7/8 | Moulding 93/07...T-133
$60 set up Type: crwnm |
| 1484 |  | 2-1/2+ x 7/8 | Moulding 100/04...T-75
$60 set up Type: bbrdm |
| 1712 |  | 2-1/2 x 13/16 | Moulding 118/07...T-165
$75 set up
spec dado size Type: cbntm |
| 1759 |  | 2-1/2 x 5/8 | Moulding 122/02...T-171
$60 set up
Symmetrical Type: chrrm |
| 1769 |  | 2-1/2 x 1-3/4 | Moulding 122/12...T-170
$75 set up add .30/ft to run twice Type: hrail |
| 1794 |  | 2-1/2 x 3/4 | Moulding 125/08...T-193
$50 set up Type: chrrm |
| 1807 |  | 2-1/2 x 2 | Moulding 126/11...T-189
$50 set up Type: miscm |
| 1825 |  | 2-1/2 x 11/16 | Moulding 128/06...T-191
$50 set up Type: casin |
| 1839 |  | 2-1/2 x 7/8 | Moulding 129/09...T-179
$50 set up Type: casin |
| 1870 |  | 2-1/2 x 1-1/16 | Moulding 132/04...T-184
$50 set up Type: chrrm |
| 1902 |  | 2-1/2 x 3/4 | Moulding 134/08...T-179
$75 set up
spec your dado dimensions Type: cbntm |
| 1915 |  | 2-1/2 x 5/8 | Moulding 135/04...T-190
$50 set up Type: casin |
| 1944 |  | 2-1/2 x 1-3/8 | Moulding 139/19...T-176$60 set up Type: crwnm |
| 1949 |  | 2-1/2 x 1-3/16 | Moulding 137/05...T-176
$50 set up Type: crwnm |
| 1955 |  | 2-1/2 x 1 | Moulding 137/11...T-177
$75 set up Type: panlm |
| 1971 |  | 2-1/2 x 3/4 | Moulding 138/09...T-180
$95 set up Type: crwnm |
| 1976 |  | 2-1/2 x 3/4 | Moulding 139/03...T-173
$60 set up Type: bbrdm |
| 1980 |  | 2-1/2 x 5/8 | Moulding 139/07...T-185
$75 set up
symmetrical Type: casin |
| 2008 |  | 2-1/2 x 13/16 | Moulding 162/07...T-207
$60 set up Type: casin |
| 2016 |  | 2-1/2 x 1-15/16 | Moulding 151/04...T-15
$60 set up Type: miscm |
| 2041 |  | 2-1/2 x 1-1/2 | Moulding 153/07...T-195
$50 set up Type: chrrm |
| 2054 |  | 2-1/2 x 1-1/16 | Moulding 154/08...T-193
$50 set up Type: crndm |
| 2082 |  | 2-1/2 x 1-15/16 | Moulding 156/09...T-199
$60 set up Type: crwnm |
| 0488 |  | 2-9/16 x 13/16 | aka beaded cabinet corner.
symmetrical, flute
Mldg 32/07...T-57
$95 set up
Type: cbntm |
| 1493 |  | 2-9/16 x 11/16 | Moulding 101/03...T-144
$50 set up Type: casin |
| 0034 |  | 2-5/8 x 1-1/8 | can be made without dado
Moulding 02/07...T-8
$75 set up Type: chrrm |
| 0214 |  | 2-5/8+- x 2-3/8 | standard shape as other handrails. The width is changeable for your application
Moulding 16/07...T-23
aka 6010 (2-3/8" x 2-1/4") and 6210 (2-3/8" x 2-7/8")
$85 set up, add .40 to run twice.
symmetrical Type: hrail |
| 0302 |  | 2-5/8 x 3/4 | Moulding 21/10...T-31
$95 set up Type: crwnm |
| 0369 |  | 2-5/8 x 3/4 | another old style two-step casing
Moulding 25/15...T-41
$75 set up, $50 w/out relief Type: casin |
| 0374 |  | 2-5/8 x 1 | Moulding 146/06...T-43
$60 set up Type: chrrm |
| 0592 |  | 2-5/8 x 3/4 | dado can be spec'd
Moulding 37/03...T-
$75 set up Type: panlm |
| 0600 |  | 2-5/8 x 1-1/4 | Can be used as a cradle too
Moulding 37/11...T-
$60 set up Type: crwnm |
| 0742 |  | 2-5/8 x 9/16 | typical old fashioned crown
Moulding 49/08...T-74
$95 set up Type: crwnm |
| 0853 |  | 2-5/8 x 7/8 | an old style picture mould
Moulding 53/10...T-77
$75 set up
Type: miscm |
| 0943 |  | 2-5/8 x 2 | dado can vary in size oval and symmetrical
Moulding 149/04...T-
$110 set up
specify your dado
Type: hrail |
| 1014 |  | 2-5/8 x 5/8 | Symmetrical, beads
Moulding 65/10...T-95 Type: chrrm |
| 1041 |  | 2-5/8 x 11/16 | Moulding 68/05...T-103
$95 set up Type: crwnm |
| 1044 |  | 2-5/8 x 3/4 | Moulding 68/08...T-106
$95 set up Type: crwnm |
| 1065 |  | 2-5/8 x 9/16 | Moulding 70/06...T-104
$50 set up Type: casin |
| 1177 |  | 2-5/8 x 1-7/16 | Moulding 77/09...T-124
$50 set up Type: chrrm |
| 1188 |  | 2-5/8 x 15/16 | Spec gap dimension
Moulding 78/08...T-84
$85 set up Type: cbntm |
| 1214 |  | 2-5/8 x 2-3/8 | Moulding 80/05...T-120
$110 set up Type: miscm |
| 1215 |  | 2-5/8 x 1-3/8 | Moulding 80/06...T-120
$95 set up Type: miscm |
| 1549 |  | 2-5/8 x 3/4 | Moulding 105/10...T-15
$50 set up Type: chrrm |
| 1569 |  | 2-5/8 x 1-3/8 | Moulding 107/06...T-151
$50 set up Type: chrrm |
| 1662 |  | 2-5/8 x 11/16 | Moulding 114/12...T-159
$50 set up Type: chrrm |
| 1753 |  | 2-5/8 x 11/16 | Moulding 121/09...T-171
$95 set up Type: panlm |
| 1813 |  | 2-5/8 x 15/16 | Moulding 127/05...T-192
$85 set up Type: casin |
| 2116 |  | 2-5/8 x 1-1/4 | Moulding 159/04...T-13,202
$60 set up Type: chrrm |
| 0382 |  | 2-11/16 x 11/16 | Moulding 26/08...T-40
$50 set up Type: panlm |
| 0709 |  | 2-11/16 x 13/16 | dado can be spec'd
Moulding 44/02...T-
$75 set up Type: panlm |
| 0037 |  | 2-3/4 x 1-1/8 | symmetrical, beads
Moulding 02/04...T-3
$50 set up Type: chrrm |
| 0098 |  | 2-3/4 x 9/16 | Moulding 08/03...T-3
aka BMC83
$95 set up Type: cvbdm |
| 0235 |  | 2-3/4 x 9/16 | Moulding 18/05...T-26
$95 set up Type: cvbdm |
| 0377 |  | 2-3/4 x 15/16 | Moulding 26/04...T-30
$50 set up Type: chrrm |
| 0391 |  | 2-3/4 x 1 | Moulding 27/01...T-34
$50 set up Type: chrrm |
| 0506 |  | 2-3/4 x 1-1/8 | Moulding 33/06...T-49
$75 set up
beaded Type: custo |
| 1381 |  | 2-3/4 x 3/4 | Moulding 92/01...T-134
$75 set up
specify dado dimension Type: casin |
| 1008 |  | 2-3/4 x 13/16 | Moulding 65/04...T-93
$50 set up Type: chrrm |
| 1019 |  | 2-3/4 x 11/16 | symmetrical
Moulding 65/15...T-95
$95 set up
used as cabinet corner treatment Type: cbntm |
| 1043 |  | 2-3/4 x 1/2 | bed
Moulding 68/07...T-101
$95 set up Type: cvbdm |
| 1092 |  | 2-3/4 x 1 | Moulding 72/10...T-97
$50 set up Type: casin |
| 1144 |  | 2-3/4 x 3/4 | Symmetrical
Moulding 74/06...T-105
beaded
$50 set up Type: casin |
| 1151 |  | 2-3/4 x 3/4 | Moulding 74/13...T-97
3/8" offset shown
$75 set up Type: cbntm |
| 1159 |  | 2-3/4 x 3/4 | Specify gap dimension, beaded
Moulding 75/05...T-104
$75 set up Type: cbntm |
| 1189 |  | 2-3/4 x 13/16 | Moulding 78/09...T-126
$75 set up, $50 w/out relief Type: casin |
| 1195 |  | 2-3/4 x 1-1/16 | Moulding 79/04...T-126
$95 set up Type: panlm |
| 1218 |  | 2-3/4 x 1-13/16 | Moulding 80-09...T-124
$60 set up Type: crwnm |
| 1258 |  | 2-3/4 x 3/4 | Symmetrical, beads
Moulding 83/04...T-116
$50 set up Type: chrrm |
| 1288 |  | 2-3/4 x 5/8 | Symmetrical, beads
Moulding 85/08...T-119
$60 set up, add .30 to run twice Type: chrrm |
| 1336 |  | 2-3/4 x 3/4 | Moulding 88/06...T-134
$75 set up, $50 w/out relief
symmetrical beaded columns is $75 set up Type: casin |
| 1340 |  | 2-3/4 x 1-1/4 | Moulding 88/10...T-134
$50 set up Type: chrrm |
| 1373 |  | 2-3/4 x 3/8 | Moulding 91/02...T-135
$50 set up, $60 for more than 2-3/4" Type: bbrdm |
| 1526 |  | 2-3/4 x 7/8 | Moulding 103/08...T-146
$75 set up Type: casin |
| 1577 |  | 2-3/4 x 5/8 | Moulding 108/01...T-152
$60 set up Type: bbrdm |
| 1596 |  | 2-3/4 x 3/4 | Moulding 109/09...T-154
beaded
$50 set up Type: casin |
| 1608 |  | 2-3/4 x 15/16 | Moulding 110/06...T-155
$75 set up Type: chrrm |
| 1612 |  | 2-3/4 x 7/8 | Moulding 110/10...T-154
$95 set up Type: panlm |
| 1669 |  | 2-3/4 x 3/4 | Moulding 115/02...T-161
$75 set up Type: casin |
| 1675 |  | 2-3/4 x 3/4 | Moulding 115/08...T-161
old style crown
$95 set up Type: crwnm |
| 1740 |  | 2-3/4 x 3/4 | Moulding 120/04...T-168
$75 set up Type: chrrm |
| 1750 |  | 2-3/4 x 1-3/8 | Moulding 121/06...T-169
$75 set up
symmetrical Type: chrrm |
| 1782 |  | 2-3/4 x 2-1/4 | Moulding 124/04...T-188
$60 set up Type: crwnm |
| 1789 |  | 2-3/4 x 3/8 | Moulding 125/03...T-192
$95 set up Type: panlm |
| 1801 |  | 2-3/4 x 1-1/4 | Moulding 126/05...T-187
$75 set up Type: panlm |
| 1887 |  | 2-3/4 x 1-1/8 | Moulding 133/05...T-179
$50 set up Type: chrrm |
| 1916 |  | 2-3/4 x 1-3/8 | Moulding 143/06...T-170,175
Use two back to back to get hand rail
Symmetrical
Quote using 8/4" Type: hrail |
| 1919 |  | 2-3/4 x 1-1/4 | Moulding 135/08...T-173
$50 set up Type: chrrm |
| 2031 |  | 2-3/4 x 3/4 | Moulding 152/07...T-197
$50 set up as shown.
Add $25 for dado Type: cbntm |
| 2044 |  | 2-3/4 x 1-1/16 | Moulding 153/10...T-197
$50 set up Type: chrrm |
| 2046 |  | 2-3/4 x 1-1/4 | Moulding 153/12...T-197
$95 set up Type: hrail |
| 2122 |  | 2-3/4 x 13/16 | Moulding 159/10...T-203
$75 set up Type: panlm |
| 0249 |  | 2-13/16 x 13/16 | used vertically to connect the face of cabinet boxes to the sides to sumulate beaded corners
Moulding 150/07...T-42
$95 set up
fluted
symmetrical Type: cbntm |
| 0381 |  | 2-13/16 x 3/4 | Beaded cabinet door frame pattern. Please spec gap dimension.
Fruit
Board 26/07...T-30
$75 set up
Type: cbntm |
| 1156 |  | 2-13/16 x 13/16 | Specify gap dimension, beaded
Moulding 75/02...T-103
$75 set up Type: cbntm |
| 1876 |  | 2-13/16 x 5/8 | Moulding 132/10...T-184
$95 set up
symmetrical
used for island/cabinet corners Type: cbntm |
| 0021 |  | 2-7/8 x 3/4 | Beaded cabinet door frame material. Please spec gap dimension.
Moulding 01/02...T-39
$75 set up Type: cbntm |
| 0131 |  | 2-7/8 x 1-1/4 | has a 3" radius, and can be any height
symmetrical
Moulding 08/13...T-26
$50 set up Type: crndm |
| 0132 |  | 2-7/8 x 1-5/16 | 3" radius on concave molding
symmetrical
Moulding 08/14...T-9
$60 set up Type: crndm |
| 0378 |  | 2-7/8 x 11/16 | Moulding 26/05...T-36
$50 set up Type: chrrm |
| 0694 |  | 2-7/8 x 1-3/8+- | Moulding 43/01...T-62
$50 set up Type: chrrm |
| 0831 |  | 2-7/8 x 2-1/4 | large OGee
Moulding 52/02...T-79
$75 set up Type: crndm |
| 0848 |  | 2-7/8 x 1-1/8 | 3/4" offset
Moulding 53/05...T-84
$75 set up Type: panlm |
| 0904 |  | 2-7/8 x 3/4 | small beaded cove
Moulding 57/10...T-84
$95 set up Type: crwnm |
| 0994 |  | 2-7/8 x 1-1/8 | Moulding 64/04...T-93
edge bead
$75 set up Type: casin |
| 1246 |  | 2-7/8 x 1/2 | Moulding 82/11...T-114
this one was used as a cradle for a compound crown
$50 set up Type: chrrm |
| 1256 |  | 2-7/8 x 3/4 | Moulding 83/02...T-112
$95 set up
Symmetrical Type: panlm |
| 1411 |  | 2-7/8 x 1 | Moulding 93/09...T-134
$95 set up Type: crwnm |
| 1672 |  | 2-7/8 x 1 | Moulding 115/05...T-162
$50 set up Type: chrrm |
| 1749 |  | 2-7/8 x 1-3/16 | Moulding 121/05...T-169
$75 set up Type: panlm |
| 1877 |  | 2-7/8 x 7/8 | Moulding 132/11...T-181
$95 set up
symmetrical beaded
an "inny" cabinet corner mould. Type: cbntm |
| 1886 |  | 2-7/8 x 3/4 | Moulding 133/04...T-183
$50 set up Type: casin |
| 1927 |  | 2-7/8 x 3/8 | Moulding 136/02...T-176
$60 set up Type: bbrdm |
| 1950 |  | 2-7/8 x 3/4 | Moulding 137/06...T-174
$60 set up Type: bbrdm |
| 2033 |  | 2-7/8 x 3/4 | Moulding 152/09...T-197
$95 set up Type: crwnm |
| 0527 |  | 2-15/16 x 1 | Moulding 34/05...T-57
$50 set up Type: chrrm |
| 0051 |  | 3+ x 5/8 | Moulding 03/12...T-8
$70 set-up Type: bbrdm |
| 0057 |  | 3+ x 1/2 | Moulding 04/06...T-21
$60 set-up Type: bbrdm |
| 0058 |  | 3 x 3/8 | Moulding 04/07...T-21
$60 set up
center dado is for a rope moulding Type: custo |
| 0078 |  | 3 x 5/8 | aka LS c-9, C9
Moulding 06/04...T-45
$75 set up, $50 w/out relief
symmetrical, little beads
Type: casin |
| 0089 |  | 3+ x 3/4 | Moulding 07/05...T-9
Two knife set-up...$95 Type: bbrdm |
| 0136 |  | 3 x 1/2 | Moulding 12/04...T-44
$110 set up
note the rounded corners Type: sidin |
| 0167 |  | 3 x 1-1/2 | aka 3" half round, and can be any height, which turns it into a bullnose if the height is more than 1-1/2".
Moulding 13/08...T-19
set up $125...three knives...difficult
symmetrical
A few misc sizes, misc species in stock. Type: crndm |
| 0168 |  | 3 x 1-1/2 | this was used as a base to insert 1/2" glass making a glass wall
symmetrical
Moulding 13/09...T-9
$75 set up
Moulding 13/09
Type: hrail |
| 0169 |  | 3 x 2-7/8 | this was used for the top of a 1/2" glass handrail, symmetrical
Moulding 13/10...T-19
$160 set up Type: hrail |
| 0224 |  | 3+ x 3/4 | Moulding 17/02...T-26
$60 set-up Type: bbrdm |
| 0243 |  | 3 x 1-1/16 | cabinet corner molding used vertically to connect front to sides of cabinet boxes.
symmetrical
Moulding 18/09...T-26
$95 set up
Type: cbntm |
| 0284 |  | 3 x 3/4 | Moulding 20/09...T-misc
$75 set up add $20 for dado
Symmetrical Type: chrrm |
| 0325 |  | 3 x 1 | dado can be any size
Moulding 142/08...T-29
$75 set up Type: chrrm |
| 0336 |  | 3 x 9/16 | Moulding 23/07...T-28
edge beads
$50 set up Type: casin |
| 0340 |  | 3 x 3/4 | Dado can be any size.
symmetrical
Moulding 24/03...T-28
$75 set up Type: chrrm |
| 0356 |  | 3 x 13/16 | symmetrical
Moulding 25/02...T-36
$50 set up Type: chrrm |
| 0366 |  | 3 x 3/4 | Moulding 25/12...T-41
$50 set up Type: casin |
| 0384 |  | 3 x 15/16 | chalk rail
Moulding 26/10...T-36
$95 set up Type: miscm |
| 0389 |  | 3 x 1-1/8 | Moulding 146/04...T-40
$75 set up Type: chrrm |
| 0426 |  | 3 x 7/8 | Moulding 29/06...T-51
$75 set up Type: casin |
| 0432 |  | 3 x 1-7/8 | Moulding 29/09...T-27
$60 set up Type: crwnm |
| 0450 |  | 3 x 5/8 | Moulding 30/02...T-54
$60 set up Type: casin |
| 0477 |  | 3 x 1-1/8 | Moulding 144/09...T-27
$50 set up Type: crndm |
| 0531 |  | 3 x 1-5/8 | Moulding 34/09...T-48
$50 set up Type: crwnm |
| 0558 |  | 3+ x 3/4 | Moulding 35/12...T-56
$60 set up Type: miscm |
| 0569 |  | 3 x 13/16 | Moulding 145/06...T-53
$50 set-up
3"+ add $20 Type: bbrdm |
| 0571 |  | 3 x 1-3/4 | Any dado size in the bottom when specified
Moulding 36/02...T-56
$150 set-up
symmetrical Type: hrail |
| 0577 |  | 3+ x 13/16 | Spec gap dimension
Moulding 36/08...T-53
$75 set up Type: cbntm |
| 0580 |  | 3 x 13/16 | symmetrical
Moulding 36/11...T-50
$85 set up Type: chrrm |
| 0587 |  | 3+ x 3/4 | Moulding 142/04...T-50
$60 set-up Type: bbrdm |
| 0603 |  | 3 x 1 | Moulding 37/14...T-52
Three knife set-up...$95 Type: chrrm |
| 0622 |  | 3 x 13/16 | Moulding 144/10...T-60
$85 set up Type: chrrm |
| 0627 |  | 3+ x 3/8 | Moulding 39/03...T-50
$60 set-up Type: bbrdm |
| 0628 |  | 3+ x 3/4 | Moulding 39/04...T-53
one bead $60 set-up Type: bbrdm |
| 0631 |  | 3+ x 3/4 | Moulding 39/07...T-58
$50 set-up
Type: bbrdm |
| 0638 |  | 3+ x 3/4 | Moulding 144/02...T-50
$50 set-up
3-1/4 + add $20 Type: bbrdm |
| 0640 |  | 3 x 5/8 | Moulding 146/02...T-61
$75 set up, $50 w/out relief
symmetrical Type: casin |
| 0675 |  | 3+ x 1/2 | Moulding 41/18...T-67
$60 set-up Type: bbrdm |
| 0677 |  | 3 x 5/8 | Single Beaded pattern
Moulding 140/06...T-64
$110 set up
note beveled tongue and groove Type: sidin |
| 0685 |  | 3 x 1/2 | Moulding 42/05...T-63
Shown with relief on bottom adds $25
$50 set-up without relief
Type: bbrdm |
| 0690 |  | 3 x 5/8 | Moulding 42/10...T-64
$95 set up
Type: crwnm |
| 0702 |  | 3 x 1/2 | Moulding 43/09...T-62
$60 set-up Type: bbrdm |
| 0704 |  | 3+ x 3/4 | Moulding 141/03...T-59
$60 set up
Type: bbrdm |
| 0737 |  | 3 x 1 | bottom portion of a very large crown designed in two pieces. See bottom half CRWNM0736
Moulding 49/03....T-74
$95 set up for this portion. Type: crwnm |
| 0762 |  | 3 x 9/16 | Moulding 50/02...T-74
$60 set up Type: bbrdm |
| 0793 |  | 3 x 1-3/16 | the lip or lap can be spec'd to any size
Moulding 46/06...T-69
$75 set up Type: panlm |
| 0834 |  | 3 x 1-1/4 | could be a panel cap
dado can be spec'd
Moulding 52/05...T-79
$75 set up Type: panlm |
| 0863 |  | 3 x 3/4 | symmetrical
Moulding 54/05...T-81
$50 set up Type: miscm |
| 0865 |  | 3 x 3/4 | Moulding 54/07...T-79
Beads on edges
$50 set up Type: casin |
| 0866 |  | 3 x 1 | Moulding 54/08...T-84
$50 set up Type: casin |
| 0912 |  | 3 x 1-1/18 | Moulding 58/05...T-88
$50 set up Type: casin |
| 0916 |  | 3+ x 3/4 | Symmetrical
Moulding 58/09...T-90
$75 set up, add .30 to run twice Type: chrrm |
| 0955 |  | 3 x 1-1/4 | Moulding 61/04...T-87
$75 set up Type: crndm |
| 0958 |  | 3 x 3/4 | stemware wine glass holders
symmetrical
Moulding 61/07...T-90
$60 set up, run twice, add .30/foot Type: miscm |
| 0969 |  | 3 x 11/16 | Moulding 62/05...T-94
$50 set up Type: casin |
| 0987 |  | 3+ x 3/4 | Moulding 63/10...T-92
$60 set up Type: bbrdm |
| 0993 |  | 3 x 3/4 | Moulding 64/03...T-92
$60 set up Type: miscm |
| 0995 |  | 3 x 1-1/16 | beaded
Moulding 64/05...T-92
$75 set up Type: custo |
| 1009 |  | 3+ x 9/16 | Moulding 65/05...T-96
$60 set up Type: bbrdm |
| 1040 |  | 3 x 1-1/2 | Moulding 68/04...T-104
$50 set up Type: crwnm |
| 1051 |  | 3 x 3/4 | Moulding 69/03...T-107
$50 set up Type: casin |
| 1053 |  | 3 x 1-1/16 | Moulding 69/05...T-96
$50 set up Type: casin |
| 1059 |  | 3 x 1-1/8 | Moulding 69/11...T-106
$50 set up Type: casin |
| 1072 |  | 3+ x 9/16 | Moulding 70/13...T-102
$60 set up Type: bbrdm |
| 1080 |  | 3+ x 11/16 | Moulding 71/07...T-102
$50 set up as shown, $60 set up when taller Type: bbrdm |
| 1090 |  | 3+ x 3/8 | Moulding 72/08...T-110
$60 set up Type: bbrdm |
| 1093 |  | 3 x 3/8 | Moulding 72/11...T-101
$60 set up Type: bbrdm |
| 1104 |  | 3 x 11/16 | Moulding 73/11...T-97
$50 set up Type: chrrm |
| 1115 |  | 3 x 2 | Symmetrical
dado on bottom can be any size
Moulding 76/01...T-81, T-102
$125 set up, add $.60/foot to run three times.
Type: hrail |
| 1226 |  | 3 x 1-1/2 | Moulding 81-05...T-122
Symmetrical
$75 set up
give dado dimensions Type: chrrm |
| 1227 |  | 3 x 1 | Moulding 81/06...T-126
$75 set up
dado can be any size or not at all Type: chrrm |
| 1275 |  | 3 x 3/4 |
Symmetrical
Moulding 84/06...T-120
$50 set up Type: casin |
| 1286 |  | 3 x 13/16 | Moulding 85/06...T-117
$50 set up Type: chrrm |
| 1287 |  | 3 x 3/4 | Moulding 85/07...T-41 ...see 25/12
$75 set up with relief Type: chrrm |
| 1293 |  | 3+ x 7/8 | Moulding 85/13...T-118
$50 set up
$60 for 3-1/2" + Type: bbrdm |
| 1315 |  | 3 x 1 | Moulding 87/02...T-142
$50 set up Type: casin |
| 1321 |  | 3 x 11/16 | Moulding 87/08...T-142
$50 set up Type: chrrm |
| 1338 |  | 3 x 1 | Moulding 88/08...T-131
$50 set up Type: chrrm |
| 1339 |  | 3 x 3/4 | Moulding 88/09...T-139
$60 set up
symmetrical
flute Type: casin |
| 1342 |  | 3 x 3/4 | Moulding 88/12...T-138
$50 set up Type: chrrm |
| 1352 |  | 3 x 3/4 | Moulding 89/10...T-142
$50 set up Type: casin |
| 1435 |  | 3 x 3/4 | Moulding 96/09
Moulding 97/08 duplicate...T-134
$60 set up Type: bbrdm |
| 1436 |  | 3+ x 1/2 | Moulding 96/10...T-137
$60 set up Type: bbrdm |
| 1444 |  | 3 x 3/4 | Moulding 97/08
Moulding 96/09 duplicate...T-134
$60 set up Type: bbrdm |
| 1483 |  | 3 x 9/16 | Moulding 100/03...T-143
$60 set up Type: bbrdm |
| 1535 |  | 3 x 1-1/8 | Moulding 104/08...T-148
$95 set up Type: crwnm |
| 1550 |  | 3 x 1-1/8 | Moulding 105/11...T-150
$50 set up Type: casin |
| 1571 |  | 3 x 1-5/8 | Moulding 107/08...T-152
$75 set up
please spec dado if needed Type: chrrm |
| 1578 |  | 3 x 3/8 | Moulding 108/02...T-151
$60 set up Type: bbrdm |
| 1589 |  | 3 x 1-3/4 | Moulding 109/02...T-153
$60 set up Type: casin |
| 1623 |  | 3 x 7/8 | Moulding 111/07...T-156
$50 set up, $75 set up with dado as shown Type: casin |
| 1624 |  | 3 x 3/4 | Moulding 111/08...T-155
fluted, symmetrical
$50 set up Type: casin |
| 1633 |  | 3 x 3/4 | Moulding 112/05...T-158
$50 set up Type: casin |
| 1653 |  | 3 x 7/8 | Moulding 114/03...T-161
$60 set up Type: casin |
| 1700 |  | 3 x 3/4 | Moulding 117/06...T-164
$50 set up
three step casing Type: casin |
| 1822 |  | 3 x 2 | Moulding 128/03...T-33
$110 set up
add $.30 per foot to run twice Type: hrail |
| 1846 |  | 3 x 2-1/8 | Moulding 130/02...T-178
$75 set up Type: miscm |
| 1850 |  | 3 x 1 | Moulding 130/06...T-181
$50 set up Type: chrrm |
| 1854 |  | 3 x 1-1/4 | Moulding 130/10...T-186,2
$95 set up Type: crndm |
| 1857 |  | 3 x 7/8 | Moulding 130/13...T-181
$95 set up Type: crwnm |
| 1896 |  | 3+ x 3/4 | Moulding 134/02...T-188
$50 set up Type: bbrdm |
| 1921 |  | 3 x 1-1/2 | Moulding 135/10...T-176
$60 set up Type: miscm |
| 1930 |  | 3 x 13/16 | Moulding 136/05...T-173
$50 set up Type: casin |
| 1932 |  | 3 x 3/4 | Moulding 136/07...T-175
$60 set up Type: chrrm |
| 1961 |  | 3 x 1-3/4 | Moulding 137/17...T-82,171
$75 set up Type: crwnm |
| 1977 |  | 3 x 3/4 | Moulding 139/04...T-
$75 set up Type: miscm |
| 1979 |  | 3 x 1/2 | Moulding 139/06...T-186
$95 set up Type: bbrdm |
| 1982 |  | 3 x 11/16 | Moulding 139/09...T-185
$75 set up Type: casin |
| 2030 |  | 3 x 3/4 | Moulding 152/06...T-198
$75 set up Type: cbntm |
| 2040 |  | 3 x 1/2 | Moulding 153/06...T-194
$60 set up Type: casin |
| 2050 |  | 3 x 1 | Moulding 154/04...T-195
$50 set up as shown
Add $25 for dado
This is typically 3/4" thick with same top pattern Type: cbntm |
| 2077 |  | 3 x 1 | Moulding 156/04...T-199
$50 set up Type: chrrm |
| 2132 |  | 3+ x 3/4 | Moulding 160/04...T-206
$60 set up Type: bbrdm |
| 1732 |  | 3-1/16 x 13/16 | Moulding 119/13...T-167
$60 set up Type: casin |
| 2090 |  | 3-1/16 x 13/16 | Moulding 156/17...T-198
$95 set up Type: crwnm |
| 0183 |  | 3-1/8 x 3/4 | Moulding 11/12...T-35
$95 set up Type: crwnm |
| 0230 |  | 3-1/8 x 5/16 | this gives a v-joint; thin stock has to be lap joint instead of tongue and groove
Moulding 18/03...T-
$95 set up
Type: sidin |
| 0542 |  | 3-1/8 x 13/16 | Moulding 35/03...T-50
$95 set up Type: panlm |
| 0593 |  | 3-1/8 x 7/8 | Moulding 37/04...T-
$95 set up Type: panlm |
| 0612 |  | 3-1/8 x 1-1/4 | This is bottom portion of a very large crown mould. See CRWNM0596 or CRWNM0613 for two options for the top
half.
Moulding 38/05...T-47
$75 set up
Type: crwnm |
| 0634 |  | 3-1/8 x 1-1/4+- | can be any thickness or width with the pattern running on both sides.
symmetrical
Moulding 39/10...T-58
$75 set up, add $.30/lf to run twice Type: chrrm |
| 0710 |  | 3-1/8+ x 3/4 | Moulding 44/03...T-100
$95 set up
Note rounded instead of v jointed...very smooth Type: sidin |
| 0777 |  | 3-1/8 x 1/2 | Moulding 45/04...T-72
$50 set up Type: chrrm |
| 0902 |  | 3-1/8 x 5/8 | normal patterned crown just mid sized
Moulding 57/08...T-85
$95 set up Type: crwnm |
| 0934 |  | 3-1/8 x 3/4 | Moulding 60/01...T-96
big bead
$50 set up Type: casin |
| 1207 |  | 3-1/8 x 3/4 | Moulding 79/14..T-122
$85 set up Type: cbntm |
| 1314 |  | 3-1/8 x 1-1/2 | Moulding 87/01...T-142
$60 set up Type: miscm |
| 1356 |  | 3-1/8 x 3/4 | Moulding 90/03...T-137
$60 set up
symmetrical Type: casin |
| 1420 |  | 3-1/8 x 3/4 | Moulding 94/08...T-114
$95 set up
symmetrical Type: cvbdm |
| 1523 |  | 3-1/8 x 9/16 | Moulding 103/05...T-147
$60 set up Type: bbrdm |
| 1561 |  | 3-1/8 x 13/16 | Moulding 106/09...T-148
$75 set up
spec dado size Type: cbntm |
| 1591 |  | 3-1/8 x 1-1/2 | Moulding 109/04...T-153
$75 set up
please spec dado size Type: chrrm |
| 1666 |  | 3-1/8 x 11/16 | Moulding 114/16...T-160
$95 set up Type: crwnm |
| 1910 |  | 3-1/8 x 7/8 | Moulding 134/16...T-183
$95 set up
Type: crwnm |
| 0079 |  | 3-1/4+ x 1/2 | Moulding 07/01...T-7
Similar to the B-20
$50 set-up Type: bbrdm |
| 0088 |  | 3-1/4+ x 3/4 | Moulding 06/10...T-10
$50 set up
Shown with relief...add $25 Type: bbrdm |
| 0124 |  | 3-1/4+ x 1/2 | Moulding 08/11...T-9
$50 set-up Type: bbrdm |
| 0175 |  | 3-1/4 x 3/4 | Moulding 11/05...T-12
$50 set up Type: chrrm |
| 0190 |  | 3-1/4 x 3/4 | Cabinet door frame pattern. Please spec gap dimension.
Moulding 14/06...T-46
$75 set up Type: cbntm |
| 0209 |  | 3-1/4 x 11/16 | bed
Moulding 15/09...T-17
$95 set up Type: cvbdm |
| 0220 |  | 3-1/4 x 1-1/16 | Moulding 141/07...T-38
$50 set up Type: casin |
| 0265 |  | 3-1/4 x 1/2 | thin stock needs to be lap jointed. Shown is a deep v with thin lapping.
Moulding 19/09...T-
45 degrees
$95 set up Type: sidin |
| 0274 |  | 3-1/4 x 3/4 | Moulding 20/05...T-25
$60 set up Type: bbrdm |
| 0281 |  | 3-1/4 x 3/4 | Moulding 20/08...T-35
$60 set up Type: bbrdm |
| 0288 |  | 3-1/4 x 1-3/16 | can be made with or without scribing dado
Moulding 149/01...T-35
$50 set up
add $20 for dado Type: bbrdm |
| 0295 |  | 3-1/4 x 3/4 | very old casing usually used with rosettes and plinth blocks, symmetrical
Moulding 21/03...T-31
$50 set up
Type: casin |
| 0304 |  | 3-1/4 x 3/4 | Moulding 140/08...T-35
$95 set up Type: crwnm |
| 0322 |  | 3-1/4 x 3/4 | symmetrical
Moulding 22/13...T-37
$75 set up Type: chrrm |
| 0361 |  | 3-1/4+ x 1/2 | Moulding 25/07...T-41
$60 set-up
Type: bbrdm |
| 0398 |  | 3-1/4 x 1/2 | thin good two sides v-groove siding can be tongue and grooved but with shallow v
Moulding 27/09...T-44
Add $.30 per foot
$135 set up Type: sidin |
| 0401 |  | 3-1/4 x 9/16 | Moulding 27/12...T-6
$60 set-up Type: bbrdm |
| 0442 |  | 3-1/4+ x 5/8 | aka beveled base
Moulding 31/04...T-54
$50 set up Type: bbrdm |
| 0473 |  | 3-1/4 x 15/16 | Moulding 30/12...T-54
center bead
$50 set up Type: casin |
| 0537 |  | 3-1/4+ x 1/2 | Moulding 144/01...T-55
$60 set-up Type: bbrdm |
| 0539 |  | 3-1/4+ x 3/8 | Moulding 143/01...T-48
$60 set-up Type: bbrdm |
| 0547 |  | 3-1/4+ x 3/4 | Moulding 35/08...T-50
$60 set up
Type: bbrdm |
| 0594 |  | 3-1/4 x 13/16 | Moulding 37/05...T-
$95 set up Type: panlm |
| 0637 |  | 3-1/4+ x 3/4 | Moulding 39/13...T-58
set up $60 without the relief Type: bbrdm |
| 0700 |  | 3-1/4+ x 3/4 | Moulding 43/07 - T-59
$75 set up Type: bbrdm |
| 0707 |  | 3-1/4+ x 9/16 | Moulding 141/02...T-59
$60 set up Type: bbrdm |
| 0716 |  | 3-1/4 x 11/16 | Moulding 44/09...T-67
large three step casing
$75 set up, $50 w/out relief Type: casin |
| 0761 |  | 3-1/4 x 9/16 | Moulding 50/01...T-73
$60 set up Type: bbrdm |
| 0766 |  | 3-1/4 x 1-5/8 | 3-1/4" half round
symmetrical
Moulding 50/06...T-76
$125...three knives...difficult set up Type: crndm |
| 0774 |  | 3-1/4+ x 3/4 | Moulding 45/02...T-68
$60 set up
Type: bbrdm |
| 0782 |  | 3-1/4 x 9/16 | Not the standard 3-1/2" you may be looking for....
Moulding 45/10...T-73
$50 set up Type: casin |
| 0788 |  | 3-1/4 x 3/4 | Moulding 46/01...T-64
$60 set up Type: bbrdm |
| 0801 |  | 3-1/4+ x 3/4 | Moulding 47/01...T-71
$60 set up Type: bbrdm |
| 0846 |  | 3-1/4 x 15/16 | dado can be spec'd
Moulding 53/03...T-80
$75 set up Type: panlm |
| 0894 |  | 3-1/4 x 7/16 | Moulding 56/09...T-79
$60 set up Type: bbrdm |
| 0903 |  | 3-1/4 x 11/16 | old fashioned bed mold
Moulding 57/09...T/78
$95 set up Type: crwnm |
| 0911 |  | 3-1/4+ x 3/4 | Moulding 58/08..T-90
$60 set up Type: bbrdm |
| 0937 |  | 3-1/4 x 2-1/2 | Moulding 60/04...T-75
$75 set up Type: miscm |
| 0957 |  | 3-1/4 x 1/2 | Moulding 61/06...T-85
$60 set up. Similar to B-Base
Type: bbrdm |
| 0964 |  | 3-1/4 x 3/4 | symmetrical.
Moulding 61/13...T-87
$95 set up Type: crwnm |
| 0967 |  | 3-1/4 x 13/16 | Moulding 62/03...T-94
three step casing
$75 set up (Two knives) Type: casin |
| 0968 |  | 3-1/4+ x 3/4 | Moulding 62/04...T-91
$60 set up Type: bbrdm |
| 1082 |  | 3-1/4 x 9/16 | Moulding 71/09...T-105
$60 set up Type: bbrdm |
| 1139 |  | 3-1/4 x 1-3/4 | Moulding 74/01...T-100
$60 set up Type: miscm |
| 1140 |  | 3-1/4 x 1-3/4 | Moulding 74/02...T-106
$60 set up Type: miscm |
| 1141 |  | 3-1/4 x 1-3/8 | dado can be different heights
Moulding 74/03...T-100
$75 set up Type: panlm |
| 1190 |  | 3-1/4 x 1-1/16 | Moulding 78/10...T-120
$50 set up Type: casin |
| 1193 |  | 3-1/4 x 1-3/8 | Moulding 79/02...T-120
$60 set up Type: casin |
| 1274 |  | 3-1/4 x 7/8 | Beaded cabinet door moulding with dado for glass insert
Moulding 84/05...T-117
$75 set up Type: cbntm |
| 1364 |  | 3-1/4 x 3/4 | Moulding 90/11...T-140
$75 set up Type: panlm |
| 1375 |  | 3-1/4 x 1/2 | Moulding 91/04...T-135
$60 set up Type: bbrdm |
| 1442 |  | 3-1/4 x 1/2 | Moulding 97/06...T-135
$60 set up Type: bbrdm |
| 1443 |  | 3-1/4 x 3/4 | Moulding 97/07...T-134
$50 set up Type: bbrdm |
| 1494 |  | 3-1/4 x 1-1/4 | Moulding 101/04...T-144
$50 set up Type: casin |
| 1544 |  | 3-1/4 x 3/4 | Moulding 105/05...T-150
$50 set up Type: bbrdm |
| 1545 |  | 3-1/4 x 3/4 | Moulding 105/06...T-149
$60 set up Type: bbrdm |
| 1546 |  | 3-1/4 x 9/16 | Moulding 105/07...T-150
$50 set up
similar to c12 Type: casin |
| 1566 |  | 3-1/4 x 1-1/2 | Moulding 107/03...T-151
$50 set up Type: chrrm |
| 1572 |  | 3-1/4 x 1-1/4 | Moulding 107/09...T-151
$50 set up Type: chrrm |
| 1574 |  | 3-1/4 x 3/4 | Moulding 107/11...T-151
$85 set up
please spec dado dimension
beads Type: cbntm |
| 1588 |  | 3-1/4 x 2-3/4 | Moulding 109/01...T-153
$95 set up Type: miscm |
| 1601 |  | 3-1/4 x 1-1/4 | Moulding 109/14...T-154
$95 set up Type: miscm |
| 1619 |  | 3-1/4 x 3/4 | Moulding 111/03...T-155
$50 set up Type: casin |
| 1632 |  | 3-1/4 x 11/16 | Moulding 112/04...T-158
$60 set up Type: bbrdm |
| 1681 |  | 3-1/4 x 15/16 | Moulding 116/03...T-163
$60 set up Type: casin |
| 1698 |  | 3-1/4 x 3/4 | Moulding 117/04...T-164
$60 set up Type: bbrdm |
| 1703 |  | 3-1/4 x 3/4 | Moulding 117/09...T-166
$95 set up Type: crwnm |
| 1763 |  | 3-1/4 x 1-5/8 | Moulding 122/06...T-171
$75 with relief Type: chrrm |
| 1802 |  | 3-1/4 x 5/8 | Moulding 126/06...T-190
$50 set up Type: casin |
| 1811 |  | 3-1/4 x 5/8 | Moulding 127/03...T-187
$60 set up Type: bbrdm |
| 1860 |  | 3-1/4+ x 3/4 | Moulding 131/02...T-188
$60 set up Type: bbrdm |
| 1884 |  | 3-1/4 x 1/2 | Moulding 133/02...T-179
$60 set up Type: bbrdm |
| 1968 |  | 3-1/4 x 1 | Moulding 138/06...T-175
$75 set up
you can specify the dado dimensions Type: panlm |
| 1970 |  | 3-1/4 x 11/16 | Moulding 138/08...T-173
$95 set up
Type: crwnm |
| 2007 |  | 3-1/4 x 1-5/8 | Moulding 162/06...T-82, 3/4"qtr
$75 set up Type: crndm |
| 2038 |  | 3-1/4 x 9/16 | Moulding 153/04...T-194
$60 set up Type: bbrdm |
| 2114 |  | 3-1/4 x 9/16 | Moulding 159/02...T-22
$60 set up Type: bbrdm |
| 2115 |  | 3-1/4 x 3/4 | Moulding 159/03...T-203
$50 set up Type: casin |
| 0521 |  | 3-5/16 x 3/4 | rosettes or corner blocks are typically used with this older style casing.
symmetrical
Moulding 142/10...T-55
$50 set up w/out relief Type: casin |
| 0779 |  | 3-5/16 x 5/8 | This is different from the fluted casing we stock...therefore custom.
symmetrical
Moulding 45/07...T-72
$50 set up Type: casin |
| 1351 |  | 3-5/16 x 9/16 | Moulding 89/09...T-135
$75 set up, $50 w/out relief Type: casin |
| 1788 |  | 3-5/16 x 5/8 | Moulding 125/02...T-
$95 set up Type: panlm |
| 0072 |  | 3-3/8 x 5/8 | Known as the Four-beaded casing.
symmetrical
Moulding 05/13...T-2
$50 set up Type: casin |
| 0182 |  | 3-3/8 x 1-1/16 | Moulding 11/11...T-12
$150 set up Type: crwnm |
| 0293 |  | 3-3/8 x 5/8 | beaded board...tongue and groove. It comes from 1 x 4
Moulding 21/01...T-25
$95 set up Type: sidin |
| 0312 |  | 3-3/8 x 1-1/16 | Moulding 22/04...T-37
$75 set up Type: chrrm |
| 0375 |  | 3-3/8 x 1/2 | tear dropped siding
comes out of a 1 x 4
Moulding 26/02...T-36
$75 set up
Type: sidin |
| 0396 |  | 3-3/8 x 11/16 | symmetrical
Moulding 27/07...T-41
$60 set up Type: chrrm |
| 0676 |  | 3-3/8 x 7/8 | Moulding 41/19...T-67
$50 set up Type: chrrm |
| 0678 |  | 3-3/8 x 1 | Moulding 147/02...T-67
$75 set up
Beaded Type: casin |
| 0901 |  | 3-3/8 x 1-1/4 | old style crown
Moulding 57/07.../T77
$95 set up Type: crwnm |
| 1296 |  | 3-3/8 x 1-7/16 | Moulding 86/02...T-121.
$75 set up Type: chrrm |
| 1326 |  | 3-3/8 x 5/8 | Moulding 87/13...T-139
$50 set up
beaded
symmetrical Type: casin |
| 1419 |  | 3-3/8 x 13/16 | Moulding 94/07...T-127
$95 set up Type: crwnm |
| 1461 |  | 3-3/8 x 3/4 | Moulding 99/04...T-?
$75 set up Type: panlm |
| 1496 |  | 3-3/8 x 1-3/16 | Moulding 101/06...T-144
$50 set up Type: chrrm |
| 1636 |  | 3-3/8 x 1-1/16 | Moulding 112/08...T-157
$95 set up Type: crwnm |
| 1734 |  | 3-3/8 x 1/2 | Moulding 119/15...T-167
$60 set up Type: casin |
| 1751 |  | 3-3/8 x 1-1/4 | Moulding 121/07...T-170,13
$125 set up,
Add .30 per foot to run twice Type: hrail |
| 1767 |  | 3-3/8 x 5/8 | Moulding 122/10...T-
$75 set up
add $20 for dado Type: casin |
| 1792 |  | 3-3/8 x 3/4 | Moulding 125/06...T-190
$50 set up Type: casin |
| 1895 |  | 3-3/8 x 5/8 | Moulding 134/01...T-175
$60 set up
add $20 for relief Type: bbrdm |
| 2133 |  | 3-3/8 x 7/8 | Moulding 160/05...T-204
$50 set up Type: casin |
| 0165 |  | 3-7/16 x 1-5/16 | this was used for a porch wall panel where you can see the beaded pattern from both sides. Comes from 2 x 4 material.
Moulding 13/06...T-15
$105 set up plus we run it twice, therefore add another .30 per foot to foot price Type: sidin |
| 0789 |  | 3-7/16 x 3-7/16 | pretty big rail probably going to be laminated to get the size and reliability
Moulding 46/02...T-56, T-70
$125 set up, add $.60/foot for running three times.
symmetrical
Type: hrail |
| 1582 |  | 3-7/16 x 3/4 | Moulding 108/06...T-153
$75 set up as shown, $50 w/out relief Type: casin |
| 2006 |  | 3-7/16 x 1-7/16 | Moulding 162/05...T-207
$50 set up Type: casin |
| 0025 |  | 3-1/2 x 1-1/4 | aka CR-6
moulding 01/06...T-22
$75 set up Type: chrrm |
| 0030 |  | 3-1/2 x 3/4 | Very narrow KP 44 siding shown in ship lap form...can be any width specified. Beaded
Moulding 02/11...T-8
$100 set up
Type: sidin |
| 0042 |  | 3-1/2 x 5/8 | aka two-step base
Moulding 03/02...T-13
$50 set up Type: bbrdm |
| 0053 |  | 3-1/2 x 5/8 | 3-1/4" net face. Beaded
Moulding 04/02...T-15
$95 set up Type: sidin |
| 0059 |  | 3-1/2+ x 1/2 | Moulding 04/08...T-5
$60 set up Type: bbrdm |
| 0060 |  | 3-1/2 x 3/4 | symmetrical
Moulding 04/09...T-21
$60 set up, ad .30 per foot to run twice. Type: chrrm |
| 0097 |  | 3-1/2 x 3/4 | Moulding 09/01...T-16
$50 set up Type: bbrdm |
| 0123 |  | 3-1/2+ x 9/16 | aka one-step base
Moulding 10/04...T-10
$60 set up Type: bbrdm |
| 0147 |  | 3-1/2 x 3/4 | symmetrical
Moulding 13/01...T-19
tiny beads
$50 set up Type: casin |
| 0171 |  | 3-1/2 x 7/8 | Moulding 11/01...T-18
$50 set up Type: bbrdm |
| 0196 |  | 3-1/2 x 3/4 | Moulding 15/02...T-23
$75 set up Type: chrrm |
| 0241 |  | 3-1/2 x 1 | Moulding 18/08...T-26
$50 set up Type: bbrdm |
| 0242 |  | 3-1/2 x 11/16 | Moulding 17/12...T-33
$50 set up, $75 with relief Type: casin |
| 0250 |  | 3-1/2 x 5/8 | Moulding 150/01...T-42
aka C347
$60 set up
add $20 for relief Type: casin |
| 0270 |  | 3-1/2 x 5/8 | Moulding 20/04...T-25
$60 set up Type: bbrdm |
| 0277 |  | 3-1/2+ x 5/8 | Moulding 20/06...T-31
aka C295
$75 set up for either one
add $20 for dado Type: casin |
| 0278 |  | 3-1/2 x 1/2 | KP 44 style tongue and groove. Widths can be specified, usually varying. Beaded
Moulding 20/07...T-37
$95 set up Type: sidin |
| 0286 |  | 3-1/2 x 1-3/4 | Moulding 149/06...T-25
$60 set up Type: miscm |
| 0300 |  | 3-1/2 x 13/16 | this crown mounts to the top of cabinets in the orientation shown, not the front of cabinet
Moulding 21/08...T-35
$95 set up
Type: crwnm |
| 0328 |  | 3-1/2 x 3/4 | this tongue and groove plank assembled makes panels with nothing but beads....very interesting. Beaded
Moulding 147/04...T-29
$95 set up
Type: sidin |
| 0342 |  | 3-1/2 x 1-3/4 | aka a true 3-1/2" half round
symmetrical
Moulding 24/04...T-40
$125...three knives...difficult set up
We can also make a 4" half round; same set up; price 10/4 or 12/4 Type: crndm |
| 0343 |  | 3-1/2 x 13/16 | covers 2" ceiling and 3" of wall
Moulding 23/12...T-32
$95 set up Type: cvbdm |
| 0362 |  | 3-1/2 x 1-1/16 | Moulding 25/08...T-41
$50 set up
also a base board from same knife...$60 set up Type: casin |
| 0385 |  | 3-1/2+ x 9/16 | Moulding 26/11...T-36
Two knife base...$60 set up Type: bbrdm |
| 0393 |  | 3-1/2+ x 1-1/2 | Moulding 27/04...T-31
Two knife base or cradle...$60 set up Type: bbrdm |
| 0409 |  | 3-1/2 x 1 | Moulding 148/02...T-43
big bead
$50 set up Type: casin |
| 0417 |  | 3-1/2 x 3/4 | symmetrical, two flutes
Moulding 29/03...T-51
$60 set up Type: chrrm |
| 0424 |  | 3-1/2 x 2 | Moulding 28/09...T-20
$75 set up
Type: chrrm |
| 0472 |  | 3-1/2 x 5/8 | Moulding 30/11... T-51
$60 set up, dado on bottom adds $25
Type: bbrdm |
| 0474 |  | 3-1/2 x 5/8 | symmetrical
Moulding 30/13...T-54
lots of beads
$50 set up Type: casin |
| 0478 |  | 3-1/2+ x 11/16 | Moulding 142/01...T-51
Two knife base...$60 set up Type: bbrdm |
| 0572 |  | 3-1/2 x 3/4 | symmetrical, beaded
Moulding 36/03...T-53
$50 set up Type: casin |
| 0573 |  | 3-1/2 x 3/4 | beaded base
Moulding 36/04...T-53
$50 set up
add $20 for 3-1/2"+ Type: bbrdm |
| 0590 |  | 3-1/2 x 1-1/4 | Moulding 37/01... T-50
$50 set up Type: chrrm |
| 0595 |  | 3-1/2 x 13/16 | Spec gap dimension, single bead
Moulding 37/06...T-47
$75 set up Type: cbntm |
| 0623 |  | 3-1/2 x 13/16 | Moulding 140/04...T-47
one bead
$50 set up Type: bbrdm |
| 0625 |  | 3-1/2+ x 3/4 | Moulding 39/01...T-50
$60 set up
Type: bbrdm |
| 0632 |  | 3-1/2+ x 3/4 | Moulding 39/08...T-58
Two knife base...$60 set up Type: bbrdm |
| 0712 |  | 3-1/2 x 11/16 | Moulding 44/05...T-65
$75 set up. $50 w/out relief Type: casin |
| 0713 |  | 3-1/2+ x 3/4 | Moulding 44/06...T-59
$60 set up Type: bbrdm |
| 0714 |  | 3-1/2 x 3/4 | Moulding 44/07...T-68
$50 set up Type: casin |
| 0775 |  | 3-1/2 x 5/8 | A type of beaded casing but not symetrical
Moulding 45/03...T-68
$75 set up as shown with round edge
$50 set up with 2 square corners Type: casin |
| 0781 |  | 3-1/2 x 1-1/16 | Moulding 45/09...T-70
$50 set up Type: casin |
| 0783 |  | 3-1/2 x 11/16 | Moulding 45/11...T-68
$50 set up Type: casin |
| 0784 |  | 3-1/2 x 9/16 | Moulding 45/12...T-69
$95 set up Type: cvbdm |
| 0797 |  | 3-1/2 x 3/4 | symmetrical
Moulding 46/10...T-71
$50 set up Type: chrrm |
| 0807 |  | 3-1/2 x 5/8 | this is a casing similar to the B-8 base.
Moulding 47/07...T-71
$50 set up Type: casin |
| 0815 |  | 3-1/2 x 1-3/4 | symmetrical
Moulding 149/02...T-
$60 set up Type: crndm |
| 0817 |  | 3-1/2+ x 11/16 | stemware cradle for displaying drink glasses.
$60 set up
Can be made any width...requires two passes...add $.30
symmetrical
Moulding 51/04...T-82
see T-109 for one pass knife Type: miscm |
| 0833 |  | 3-1/2 x 1-1/4 | Moulding 52/04...T-82
beads
$50 set up Type: casin |
| 0838 |  | 3-1/2+ x 3/4 | Siding pieces could vary in width
Moulding 52/09...T-
$95 set up Type: sidin |
| 0864 |  | 3-1/2 x 13/16 | symmetrical bead
Moulding 54/06...T-77
$50 set up Type: casin |
| 0875 |  | 3-1/2 x 5/8 | typical colonial 3-1/2" casing
Moulding 55/06...T-57
$75 set up with dado Type: casin |
| 0876 |  | 3-1/2 x 11/16 | Moulding 55/07...T-10
aka:C12,C-12, LC11, LC-11
$50 set up Type: casin |
| 0889 |  | 3-1/2+ x 3/4 | Moulding 56/04...T-79
$60 set up Type: bbrdm |
| 0892 |  | 3-1/2+ x 9/16 | Moulding 56/07...T-85
$60 set up Type: bbrdm |
| 0893 |  | 3-1/2 x 3/4 | Moulding 56/08...T-79
single bead
$60 set up
add $20 for dado
Type: casin |
| 0907 |  | 3-1/2 x 3/4 | Moulding 58/02...T-86
$50 set up Type: casin |
| 0909 |  | 3-1/2 x 11/16 | Moulding 58/04...T-94
$50 set up
add $20 for dado Type: casin |
| 0913 |  | 3-1/2 x 1-1/2 | Moulding 58/06...T-87
beads
$50 set up Type: casin |
| 0922 |  | 3-1/2+ x 3/4 | Moulding 59/03...T-90
$60 set up Type: bbrdm |
| 0953 |  | 3-1/2+ x 3/4 | Moulding 61/02...T-90
$60 set up Type: bbrdm |
| 0956 |  | 3-1/2 x 3/4 | Moulding 61/05...T-86
$60 set up Type: bbrdm |
| 0970 |  | 3-1/2 x 3/4 | Moulding 62/06...T-93
$50 set up Type: casin |
| 0982 |  | 3-1/2 x 7/8 | Moulding 63/05...T-95
$50 set up Type: casin |
| 1047 |  | 3-1/2 x 11/16 | Moulding 68/11...T-102
$95 set up Type: crwnm |
| 1054 |  | 3-1/2 x 3/4 | Moulding 69/06...T-101
$50 set up Type: casin |
| 1055 |  | 3-1/2 x 1 | Moulding 69/07...T-106
beads
$50 set up Type: casin |
| 1057 |  | 3-1/2 x 3/4 | Moulding 69/09...T-102
$50 set up Type: casin |
| 1058 |  | 3-1/2 x 3/4 | Moulding 69/10...T-98
$75 set up Type: casin |
| 1066 |  | 3-1/2 x 3/8 | Moulding 70/07...T-98
$50 set up Type: casin |
| 1070 |  | 3-1/2 x 5/8 | Moulding 70/11...T-105
$60 set up Type: bbrdm |
| 1071 |  | 3-1/2 x 5/8 | Moulding 70/12...T-102
$60 set up Type: bbrdm |
| 1086 |  | 3-1/2 x 9/16 | Moulding 72/04...T-100
$60 set up Type: bbrdm |
| 1087 |  | 3-1/2+ x 3/4 | Moulding 72/05...T-108
$60 set up Type: bbrdm |
| 1091 |  | 3-1/2 x 1 | Moulding 72/09...T-108
$60 set up Type: casin |
| 1097 |  | 3-1/2 x 1-5/8 | Symmetrical
Moulding 73/04...T-100
$50 set up Type: chrrm |
| 1099 |  | 3-1/2 x 11/16 | Moulding 73/06...T-99
$50 set up Type: chrrm |
| 1102 |  | 3-1/2 x 3/4 | Symmetrical
Moulding 73/09...T-99
$50 set up Type: chrrm |
| 1167 |  | 3-1/2 x 3/4 | one pass stemware glass rail. Symmetrical
Moulding 75/13...T-109
$60 set up
see MISCM0817 for other widths than 3-1/2" Type: miscm |
| 1170 |  | 3-1/2+ x 3/4 | Moulding 77/02...T-122
$60 set up Type: bbrdm |
| 1171 |  | 3-1/2+ x 13/16 | Moulding 77/03...T-59
$60 set up Type: bbrdm |
| 1172 |  | 3-1/2 x 1 | Moulding 77/04...T-126
$50 set up Type: chrrm |
| 1225 |  | 3-1/2 x 1 | Symmetrical
Moulding 81/04...T-113
$50 set up Type: chrrm |
| 1228 |  | 3-1/2 x 3/4 | Symmetrical
Moulding 81/07...T-112
$50 set up add .30 for second pass Type: chrrm |
| 1229 |  | 3-1/2 x 3/4 | Moulding 81/08...T-113
$75 set up Type: casin |
| 1235 |  | 3-1/2 x 3/4 | Moulding 81/14...T-
$95 set up Type: crwnm |
| 1272 |  | 3-1/2 x 1 | Moulding 84/04...T-115
double beads
$50 set up Type: casin |
| 1276 |  | 3-1/2 x 1-1/4 | Moulding 84/07...T-118
$50 set up Type: chrrm |
| 1277 |  | 3-1/2 x 9/16 | Moulding 84/08...T-111
$60 set up Type: bbrdm |
| 1278 |  | 3-1/2 x 1-1/2 | Symmetrical
Moulding 84/09...T-117
$50 set up Type: chrrm |
| 1283 |  | 3-1/2 x 2-1/4 | Moulding 85/03...T-119
$75 set up
give dado dimensions Type: chrrm |
| 1290 |  | 3-1/2 x 13/16 | Moulding 85/10...T-119
fluted, symmetrical
$50 set up Type: casin |
| 1299 |  | 3-1/2 x 3/4 | Moulding 86/05...T-21
symmetrical
$50 set up Type: casin |
| 1306 |  | 3-1/2 x 3/4 | Moulding 86/12...T-misc
used as a wainscoat cap
$95 set up Type: chrrm |
| 1337 |  | 3-1/2 x 1 | Moulding 88/07...T-141
$50 set up without relief Type: chrrm |
| 1345 |  | 3-1/2 x 1-1/8 | Moulding 89/03...T-141
$50 set up
Similar to C196 Type: chrrm |
| 1346 |  | 3-1/2 x 1-1/4 | Moulding 89/04...T-140
$60 set up Type: chrrm |
| 1349 |  | 3-1/2 x 3/4 | Moulding 89/07...T-140
$75 set up, $50 w/out relief Type: casin |
| 1350 |  | 3-1/2 x 15/16 | Moulding 89/08...T-132
$75 set up, $50 w/out relief Type: casin |
| 1380 |  | 3-1/2 x 3/8 | Moulding 91/09...T-129
thin and small, lap only
$75 set up Type: sidin |
| 1433 |  | 3-1/2 x 3/4 | Moulding 96/07...T-142
$60 set up Type: bbrdm |
| 1434 |  | 3-1/2 x 9/16 | Moulding 96/08...T-128
$60 set up Type: bbrdm |
| 1445 |  | 3-1/2 x 3/4 | Moulding 97/09...T-140
$60 set up Type: bbrdm |
| 1495 |  | 3-1/2 x 3/4 | Moulding 101/05...T-145
fluted, symmetrical
$60 set up Type: casin |
| 1524 |  | 3-1/2 x 5/8 | Moulding 103/06...T-148
$60 set up Type: bbrdm |
| 1528 |  | 3-1/2 x 5/8 | Moulding 104/01...T-149
$60 set up Type: bbrdm |
| 1570 |  | 3-1/2 x 1-7/8 | Moulding 107/07...T-152
$95 set up Type: miscm |
| 1595 |  | 3-1/2 x 9/16 | Moulding 109/08...T-151
fluted, symmetrical
$50 set up Type: casin |
| 1604 |  | 3-1/2 x 13/16 | Moulding 110/02...T-156
$60 set up Type: bbrdm |
| 1649 |  | 3-1/2 x 9/16 | Moulding 113/11...T-159
symmetrical
$95 set up Type: crwnm |
| 1685 |  | 3-1/2 x 1-3/8 | Moulding 116/07...T-163
$50 set up Type: chrrm |
| 1693 |  | 3-1/2 x 5/8 | Moulding 116/15...T-164
fluted
symmetrical
$60 set up Type: casin |
| 1707 |  | 3-1/2 x 1-1/16 | Moulding 118/02...T-165
$60 set up Type: bbrdm |
| 1708 |  | 3-1/2 x 3/4 | Moulding 118/03...T-165
$50 set up Type: chrrm |
| 1715 |  | 3-1/2 x 11/16 | Moulding 118/10...T-164
$75 set up Type: chrrm |
| 1746 |  | 3-1/2 x 1-1/4 | Moulding 121/02...T-169
$75 set up Type: panlm |
| 1754 |  | 3-1/2 x 13/16 | Moulding 121/10...T-3
bead
$60 set up Type: bbrdm |
| 1766 |  | 3-1/2 x 3/4 | Moulding 122/09...T-29
beaded
$60 set up Type: bbrdm |
| 1768 |  | 3-1/2 x 1-1/16 | Moulding 122/11...T-170
Beaded
$75 set up Type: casin |
| 1793 |  | 3-1/2 x 3/4 | Moulding 125/07...T-187
$60 set up Type: casin |
| 1803 |  | 3-1/2 x 1-1/4 | Moulding 126/07...T-189
$75 set up Type: chrrm |
| 1832 |  | 3-1/2 x 1 | Moulding 129/02...T-180
$60 set up Type: casin |
| 1847 |  | 3-1/2 x 1-1/2 | Moulding 130/03...T-179
$110 set up
Type: hrail |
| 1868 |  | 3-1/2 x 3/4 | Moulding 132/02...T-21
$60 set up Type: bbrdm |
| 1890 |  | 3-1/2 x 3/4 | Moulding 133/08...T-18
$60 set up
fluted symmetrical Type: chrrm |
| 1891 |  | 3-1/2 x 3/4 | Moulding 133/08...T-18
$60 set up
fluted symmetrical Type: chrrm |
| 1892 |  | 3-1/2 x 3/4 | Moulding 133/09...T-180
$60 set up
fluted symmetrical Type: chrrm |
| 1898 |  | 3-1/2 x 1/2 | Moulding 134/04...T-176
$60 set up
symmetrical fluted Type: casin |
| 1923 |  | 3-1/2 x 13/16 | Moulding 135/12...T-173
$95 set up
symmetrical
Type: crwnm |
| 1945 |  | 3-1/2 x 3/4 | Moulding 137/01...T-172
$60 set up Type: casin |
| 1946 |  | 3-1/2 x 7/8 | Moulding 137/02...T-173
$50 set up Type: chrrm |
| 1966 |  | 3-1/2 x 3/4 | Moulding 138/04...T-192
%0 set up
symmetrical Type: chrrm |
| 1981 |  | 3-1/2 x 3/4 | Moulding 139/08...T-180
$120 set up Type: custo |
| 1992 |  | 3-1/2 x 5/8 | Moulding 161/04...T-204
$50 set up Type: casin |
| 2027 |  | 3-1/2 x 3/4 | Moulding 152/03...T-197
$85 set up Type: casin |
| 2039 |  | 3-1/2 x 11/16 | Moulding 153/05...T-195
$50 set up
similar to c12 Type: casin |
| 2045 |  | 3-1/2 x 3/4 | Moulding 153/11...T-197
symmetrical
$50 set up Type: casin |
| 2094 |  | 3-1/2 x 7/8 | Moulding 157/04...T-200
$50 set up Type: casin |
| 2097 |  | 3-1/2 x 1-3/8 | Moulding 157/07...T-200
bottom half of large crown. see crwnm2098 for top half
$75 set up Type: crwnm |
| 0626 |  | 3-9/16 x 9/16 | Moulding 39/02...T-58
$50 set up Type: casin |
| 1284 |  | 3-9/16 x 3/4 | Moulding 85/04...T-117
$50 set up Type: casin |
| 1648 |  | 3-9/16 x 3/4 | Moulding 113/10...T-158
dental or rope
$95 set up Type: crwnm |
| 2127 |  | 3-9/16 x 1 | Moulding 159/15...T-202
$95 set up Type: crwnm |
| 0232 |  | 3-5/8 x 3/4 | symmetrical
Moulding 17/07...T-33
$50 set up Type: chrrm |
| 0455 |  | 3-5/8 x 3/4 | Moulding 30/03...T-54
$95 set up Type: crwnm |
| 0525 |  | 3-5/8 x 5/8 | symmetrical, beads
Moulding 34/03...T-28
$50 set up Type: casin |
| 0810 |  | 3-5/8 x 3/4 | Moulding 47/10...T-72
$95 set up Type: crwnm |
| 0818 |  | 3-5/8 x 5/8 | Just a beveled siding
Moulding 51/05...T-86
$60 set up Type: sidin |
| 1045 |  | 3-5/8 x 3/4 | Moulding 68/09...T-108
$95 set up Type: crwnm |
| 1095 |  | 3-5/8 x 1 | Symmetrical
Moulding 73/02...T-99
$50 set up Type: chrrm |
| 1096 |  | 3-5/8 x 3/4 | Moulding 73/03...T-103
$50 set up, add $20 for relief Type: chrrm |
| 1236 |  | 3-5/8 x 3/4 | Moulding 82/01...T-110
$75 set up Type: bbrdm |
| 1237 |  | 3-5/8 x 7/8 | Moulding 82/02...T-115
$60 set up Type: bbrdm |
| 1238 |  | 3-5/8 x 3/8 | Moulding 82/03...T-115
lots of flutes, symmetrical
$60 set up Type: casin |
| 1348 |  | 3-5/8 x 1-1/4 | Moulding 89/06...T-134
$60 set up Type: chrrm |
| 1354 |  | 3-5/8 x 1-1/8 | Moulding 90/01...T-137
$60 set up Type: chrrm |
| 1451 |  | 3-5/8 x 3/4 | Moulding 98/06...T-138
$120 set up Type: cvbdm |
| 1556 |  | 3-5/8 x 7/8 | Moulding 106/04...T-150
$50 set up Type: chrrm |
| 1590 |  | 3-5/8 x 3/4 | Moulding 109/03...T-153
$50 set up Type: bbrdm |
| 1697 |  | 3-5/8 x 1/2 | Moulding 117/03...T-163
$60 set up Type: bbrdm |
| 1765 |  | 3-5/8 x 3/4 | Moulding 122/08...T-170
beaded
$60 set up Type: casin |
| 1918 |  | 3-5/8 x 1 | Moulding 135/07...T-175
$50 set up Type: chrrm |
| 1929 |  | 3-5/8 x 1-1/8 | Moulding 136/04...T-176
$50 set up Type: casin |
| 2005 |  | 3-5/8 x 3/4 | Moulding 162/04...T-207
$60 set up Type: casin |
| 2095 |  | 3-5/8 x 3/4 | Moulding 157/05...T-201
$50 set up Type: casin |
| 0080 |  | 3-11/16 x 3/4 | aka 5-bead casing.
symmetrical Beaded
Moulding 07/02...T-3
$50 set up Type: casin |
| 1108 |  | 3-11/16 x 3/4 | Moulding 66/03...T-106
$95 set up Type: crwnm |
| 0199 |  | 3-3/4 x 7/8 | Plump casing
Moulding 145/03...T-21
$50 set up Type: casin |
| 0251 |  | 3-3/4 x 1-7/16 | designed for table edge
Moulding 149/08...T-38
$110 set up Type: crndm |
| 0338 |  | 3-3/4 x 1-1/16 | Moulding 24/02...T-32
$75 set up Type: chrrm |
| 0388 |  | 3-3/4 x 13/16 | Moulding 150/05...T-36
$50 set up Type: casin |
| 0414 |  | 3-3/4 x 5/8 | symmetrical
Moulding 29/02...T-27
$50 set up Type: chrrm |
| 0430 |  | 3-3/4 x 1-1/8 | Moulding 143/15...T-35
$125 set up
add $.60 per foot for having to run twice
t15,t35,30* Type: cvbdm |
| 0471 |  | 3-3/4+ x 9/16 | shown with rounded bottom but base doesn't need it.
Moulding 30/10...T-54
aka B395 or B695
$60 set up Type: bbrdm |
| 0591 |  | 3-3/4 x 1-3/8 | Moulding 37/02...T-50
$50 set up Type: chrrm |
| 0820 |  | 3-3/4 x 5/8 | Moulding 51/07...T-83
$75 set up Type: chrrm |
| 0855 |  | 3-3/4 x 13/16 | Moulding 53/12...T-84
$75 set up $50 without relief in back. Type: chrrm |
| 0861 |  | 3-3/4 x 1-1/8 | Moulding 54/03...T-83
$50 set up Type: casin |
| 0900 |  | 3-3/4 x 1-5/16 | very interesting crown
Moulding 57/06...T-77
$95 set up Type: crwnm |
| 1002 |  | 3-3/4 x 13/16 | Moulding 64/12...T-92
$95 set up Type: crwnm |
| 1005 |  | 3-3/4 x 1-1/2 | Moulding 65/01...T-95
$50 set up Type: casin |
| 1026 |  | 3-3/4 x 3 | dado on bottom can be whatever size specified
Moulding 141/05...T-
$150 set up, add .60/foot for running three times.
Symmetrical Type: hrail |
| 1036 |  | 3-3/4 x 13/16 | flat spot for rope or dentil
Moulding 67/07...T-102
$95.00 set up Type: crwnm |
| 1265 |  | 3-3/4 x 3/4 | the dado is for a rope or dentil
Moulding 83/11...T-115
$95 set up Type: crwnm |
| 1271 |  | 3-3/4 x 1-1/8 | Moulding 84/03...T-117
$60 set up Type: bbrdm |
| 1407 |  | 3-3/4 x 13/16 | Moulding 93/05...T-131
$95 set up Type: crwnm |
| 1565 |  | 3-3/4 x 1-1/8 | Moulding 107/02...T-147
$50 set up Type: casin |
| 1606 |  | 3-3/4 x 1-3/4 | Moulding 110/04...T-155
$80 set up Type: miscm |
| 1704 |  | 3-3/4 x 13/16 | Moulding 117/10...T-165
$95 set up Type: crwnm |
| 1834 |  | 3-3/4 x 1 | Moulding 129/04...T-180
$60 set up Type: bbrdm |
| 1969 |  | 3-3/4 x 1 | Moulding 138/07...T-
$50 set up
symmetrical
fluted cabinet corner set up $95 Type: casin |
| 2017 |  | 3-3/4 x 5/8 | Moulding 151/05...T-177
$60 set up, add .30 per foot to run twice
Symmetrical Type: casin |
| 2036 |  | 3-3/4 x 1/2 | Moulding 153/02...T-194
$50 set up ad $20 for dado Type: bbrdm |
| 0648 |  | 3-7/8 x 1 | Moulding 40/01...T-62
$50 set up Type: chrrm |
| 0790 |  | 3-7/8 x 1-3/4 | symmetrical
Moulding 46/03...T-70
$95 set up Type: miscm |
| 0973 |  | 3-7/8 x 13/16 | Moulding 62/09...T-92
$95 set up Type: crwnm |
| 1098 |  | 3-7/8 x 1-3/4 | Moulding 73/05...T-101
$50 set up Type: chrrm |
| 1109 |  | 3-7/8 x 3/4 | Moulding 66/04...T-97
$95 set up Type: crwnm |
| 1158 |  | 3-7/8 x 1 | Specify gap dimension, mixed bead
Moulding 75/04...T-108
$85 set up Type: cbntm |
| 1298 |  | 3-7/8 x 1-1/16 | Moulding 86/04...T-121
$50 set up Type: chrrm |
| 1456 |  | 3-7/8 x 1-3/4 | Moulding 98/11...T-138
$95 set up Type: miscm |
| 1522 |  | 3-7/8 x 3/4 | Moulding 103/04...T-146
$60 set up Type: bbrdm |
| 1687 |  | 3-7/8 x 2-1/16 | Moulding 116/09...T-163
$95 set up Type: casin |
| 1833 |  | 3-7/8 x 7/8 | Moulding 129/03...T-185
$60 set up Type: bbrdm |
| 2011 |  | 3-7/8 x 1 | Moulding 162/10...T-207
$95 set up Type: cvbdm |
| 0202 |  | 3-15/16 x 1-3/4 | Moulding 15/06...T-18
$60 set up Type: miscm |
| 0022 |  | 4+ x 3/4 | Moulding 01/03...T-39
one bead
$60 set up Type: bbrdm |
| 0047 |  | 4 x 1 | symmetrical
Moulding 142/07...T-13
$95 set up Type: chrrm |
| 0100 |  | 4 x 1 | goes with [BBRDM0102]
symmetrical
Moulding 08/04...T-3
$95 set up
add $20 for the relief Type: chrrm |
| 0102 |  | 4+ x 1 | goes well with [CHRRM0100]
Moulding 08/05...T-3
large bead
Two knife base...$60 set up.
Relief is $20 more Type: bbrdm |
| 0125 |  | 4 x 1-3/4 | wall cap
symmetrical
Moulding 10/06...T-10
$75 set up Type: miscm |
| 0210 |  | 4+ x 3/4 | can be used as large as 8-1/2" wide flutes.
symmetrical
Moulding 15/11...T-12
fluted
increments at 3.25, 4, 4.75, 5.5 etc.
$75 set up Type: casin |
| 0211 |  | 4 x 1-9/16 | Moulding 16/05...T-23
$95 set up Type: thrsm |
| 0213 |  | 4 x 1-3/4 | wall or railing cap. Bottom can have any size dado for your application
Moulding 16/06...T-23
$110 set up
Type: hrail |
| 0229 |  | 4 x 3/4 | symmetrical
Moulding 17/05...T-42
$50 set up Type: crndm |
| 0248 |  | 4 x 1-1/8 | Moulding 149/03...T-33
$75 set up Type: chrrm |
| 0253 |  | 4 x 5/8 | bed
Moulding 150/15...T-42
$95 set up Type: cvbdm |
| 0260 |  | 4 x 1-1/4 | Moulding 20/01...T-35
$50 set up
add $20 for dado Type: bbrdm |
| 0272 |  | 4+ x 3/4 | Moulding 19/14...T-24
$60 set up
Dado on bottom and relief add $20 each.
Type: bbrdm |
| 0310 |  | 4+ x 1-3/4 | Moulding 22/01...T-35
nice mantle treatment
$95 set up Type: miscm |
| 0346 |  | 4+ x 3/4 | Moulding 24/06...T-32
Two knife base...$60 set up
Type: bbrdm |
| 0348 |  | 4+ x 11/16 | Moulding 24/07...T-28
Two knife base...$60 set up. Dado on bottom and relief cuts add $20 each. Type: bbrdm |
| 0349 |  | 4+ x 11/16 | Moulding 24/08...T-32
Two knife set up...$60 Type: bbrdm |
| 0351 |  | 4 x 3/4 | Moulding 146/01...T-60
$60 set up
if any spacing of bevels are changed, the set up $ will change too. Type: bbrdm |
| 0355 |  | 4+ x 11/16 | Moulding 25/01...T-40
one bead
$60 set up Type: bbrdm |
| 0394 |  | 4 x 3/4 | tab size can be spec'd
Moulding 27/05...T-34
$75 set up Type: panlm |
| 0411 |  | 4+ x 3/4 | narrower widths available
Moulding 28/01...T-9
three knife set up...$80 Type: bbrdm |
| 0443 |  | 4+ x 9/16 | Moulding 31/05...T-51
$60 set up Type: bbrdm |
| 0463 |  | 4+ x 7/8 | Moulding 30/06...T-51
one bead
$50 set up
add $20 for dado Type: bbrdm |
| 0507 |  | 4 x 1 | Moulding 33/07...T-23
$60 set up Type: miscm |
| 0520 |  | 4+ x 3/4 | Moulding 140/03...T-51
one bead
Two knife set up...$60
Type: bbrdm |
| 0549 |  | 4+ x 3/4+ | Moulding 35/10...T-56
$60 set up Type: bbrdm |
| 0565 |  | 4+ x 9/16 | Moulding 143/02...T-56
$50 set up Type: bbrdm |
| 0618 |  | 4 x 13/16 | Moulding 38/11...T-60
$95 set up Type: bbrdm |
| 0630 |  | 4+ x 1-1/4 | Moulding 39/06...T-
$50 set up Type: bbrdm |
| 0642 |  | 4+ x 1-3/8 | Moulding 145/02...T-53
one bead
Two knife base...$60 Type: bbrdm |
| 0656 |  | 4+ x 1-1/2 | the height can vary to your specs
Moulding 40/09
$110 set up Type: hrail |
| 0657 |  | 4 x 1-1/4+- | panel cap or wainscoating cap or just chair rail.
It is actually a modified CR-6
Moulding 40/10...T-61
$75 set up as shown Type: chrrm |
| 0681 |  | 4+ x 3/4 | Moulding 42/01...T-62
$60 set up Type: bbrdm |
| 0684 |  | 4 x 1/2 | Moulding 42/04...T-63
$50 set up
add $25 for dado Type: bbrdm |
| 0687 |  | 4 x 3/4 | symmetrical, beads
Moulding 42/07...T-63
$75 set up Type: chrrm |
| 0695 |  | 4+ x 9/16 | Moulding 43/02...T-61
Two knife base...$60 set up Type: bbrdm |
| 0697 |  | 4+ x 5/8 | Moulding 43/04...T-60
$60 set up
Type: bbrdm |
| 0698 |  | 4+ x 5/8 | Moulding 43/05...T-62
$60 set up Type: bbrdm |
| 0699 |  | 4+ x 1/2 | Moulding 43/06...T-59
$60 set up Type: bbrdm |
| 0715 |  | 4 x 1-1/2 | Moulding 44/08
$95 set up
Type: crwnm |
| 0733 |  | 4+ x 3/4 | Moulding 48/12...T-76
$60 set up Type: bbrdm |
| 0763 |  | 4 x 1/2 | Moulding 50/03...T-73
$60 set up Type: bbrdm |
| 0811 |  | 4 x 13/16 | symmetrical
Moulding 47/11...T-71
$95 set up Type: cvbdm |
| 0835 |  | 4 x 1-1/4 | Moulding 52/06...T-80
$95 set up Type: crwnm |
| 0836 |  | 4 x 1 | large OGee crown
Moulding 52/07...T-80
$95 set up Type: crwnm |
| 0847 |  | 4 x 1 | could be a panel cap
Moulding 53/04...T-78
$75 set up Type: chrrm |
| 0877 |  | 4 x 1 | Moulding 55/08...T-78
$50 set up Type: casin |
| 0923 |  | 4 x 1-5/8 | Moulding 59/04...T-88
$75 set up, add .30 per foot to run twice. Type: custo |
| 0951 |  | 4+ x 3/4 | Moulding 61/01...T-88
$60 set up Type: bbrdm |
| 0978 |  | 4+ x 3/4 | Moulding 63/01...T-91
$60 set up Type: bbrdm |
| 0979 |  | 4 x 3/4 | Moulding 63/02...T-94
$80 set up Type: bbrdm |
| 0985 |  | 4 x 3/4 | symmetrical
Moulding 63/08...T-93
$50 set up Type: casin |
| 1052 |  | 4 x 1 | Moulding 69/04...T-105
$50 set up Type: casin |
| 1068 |  | 4+ x 3/4 | Moulding 70/09...T-105
$60 set up Type: bbrdm |
| 1076 |  | 4+ x 3/4 | Moulding 71/03...T-110
$60 set up
add $20 for relief on back Type: bbrdm |
| 1088 |  | 4+ x 3/4 | Moulding 72/06...T-101
$60 set up Type: bbrdm |
| 1089 |  | 4 x 3/4 | Moulding 72/07...T-55
$75 set up
add $20 for relief Type: bbrdm |
| 1118 |  | 4 x 1-1/2 | symmetrical
Moulding 33/07
$60 set up
Moulding 76/04...T-96
$60 set up, add .30 per ft to run twice
Type: crndm |
| 1169 |  | 4+ x 3/4 | moulding 77/01...T-122
$60 set up Type: bbrdm |
| 1182 |  | 4 x 3/4 | Moulding 78/02...T-124
Symmetrical, flutes
$50 set up Type: casin |
| 1197 |  | 4 x 3/4 | Symmetrical, beads
Moulding 79/05...T-116
$50 set up Type: chrrm |
| 1245 |  | 4 x 3/4 | Moulding 82/10...T-114
$60 set up Type: bbrdm |
| 1289 |  | 4 x 13/16 | Moulding 85/09...T-120
$50 set up Type: bbrdm |
| 1344 |  | 4 x 1 | Moulding 89/02...T-134
$50 set up Type: casin |
| 1347 |  | 4 x 3/4 | Moulding 89/05...T-137
$85 set up Type: casin |
| 1374 |  | 4 x 3/4 | Moulding 91/03...T-132
$60 set up
add $25 for angle on bottom Type: bbrdm |
| 1510 |  | 4 x 2-1/2 | Moulding 102/06...T-146
$125 set up
symmetrical
laminated to get it this big
Type: hrail |
| 1529 |  | 4 x 3/4 | Moulding 104/02...T-148
$60 set up, add.30/lf for running twice
symmetrical Type: chrrm |
| 1540 |  | 4 x 2-1/16 | Moulding 105/01...T-149
$60 set up Type: casin |
| 1542 |  | 4 x 11/16 | Moulding 105/03...T-149
$60 set up Type: bbrdm |
| 1553 |  | 4 x 1 | Moulding 106/01...T-150
$60 set up Type: casin |
| 1581 |  | 4 x 3/4 | Moulding 108/05...T-154
$60 set up Type: bbrdm |
| 1663 |  | 4 x 2-3/4 | Moulding 114/13...T-159$60 set uo
window mullion Type: custo |
| 1665 |  | 4 x 1-1/16 | Moulding 114/15...T-160
$125 set up
ad .40 per foot to run twice Type: cvbdm |
| 1699 |  | 4 x 9/16 | Moulding 117/05...T-164
$60 set up Type: bbrdm |
| 1735 |  | 4 x 1/2 | Moulding 119/16...T-167
$60 set up Type: bbrdm |
| 1741 |  | 4 x 2 | Moulding 120/05...T-168
$125 set up
Symmetrical Type: crndm |
| 1745 |  | 4 x 5/8 | Moulding 121/01...T-169
$60 set up Type: bbrdm |
| 1781 |  | 4 x 1-3/4 | Moulding 124/03...T-
Cradle
$95 set up Type: crwnm |
| 1799 |  | 4 x 2 | Moulding 126/03...T-183
$50 set up Type: chrrm |
| 1800 |  | 4 x 1-1/4 | Moulding 126/04...T-182
$75 set up Type: chrrm |
| 1804 |  | 4 x 5/8 | Moulding 126/08...T-192
$50 set up
symmetrical Type: chrrm |
| 1871 |  | 4 x 1-7/8 | Moulding 132/05...T-190
$50 set up Type: chrrm |
| 1885 |  | 4+ x 1/2 | Moulding 133/03...T-181
$60 set up
$85 if need rounded bottom Type: bbrdm |
| 1888 |  | 4 x 1-3/8 | Moulding 133/06...T-180
$50 set up
Type: chrrm |
| 1899 |  | 4 x 3/4 | Moulding 134/05...T-188
$75 set up
symmetrical
Type: chrrm |
| 1922 |  | 4 x 3/4 | Moulding 135/11...T-172
$75 set up
Symmetrical Type: chrrm |
| 1960 |  | 4 x 13/16 | Moulding 137/16...T-
$95 set up
add $.30 per foot to run twice Type: cvbdm |
| 1972 |  | 4 x 13/16 | Moulding 138/10..T-172
$95 set up Type: crwnm |
| 2003 |  | 4 x 3/4 | Moulding 162/02...T-207
$60 set up Type: bbrdm |
| 2022 |  | 4 x 11/16 | Moulding 151/10...T-44
specialized siding
$95 set up Type: panlm |
| 2024 |  | 4 x 7/8 | Moulding 151/12...T-196
$95 set up
large bed mould Type: cvbdm |
| 2035 |  | 4+ x 3/4 | Moulding 153/01...T-194
$60 set up Type: bbrdm |
| 2037 |  | 4 x 3/4 | Moulding 153/03...T-195
$60 set up Type: bbrdm |
| 2075 |  | 4 x 15/16 | Moulding 156/02...T-199
$60 set up Type: bbrdm |
| 2076 |  | 4 x 1-1/4 | Moulding 156/03...T-199
$50 set up Type: casin |
| 2130 |  | 4+ x 3/4 | Moulding 160/02...T-204
$60 set up Type: bbrdm |
| 1798 |  | 4-1/16 x 3/4 | Moulding 126/02...T-185
$50 set up Type: casin |
| 0222 |  | 4-1/8 x 1-5/16 | Moulding 140/09...T-33
$95 set up Type: crwnm |
| 0303 |  | 4-1/8 x 1-1/4 | Moulding 21/11...T-35
$120 set up
add $.60 per foot for having to run twice Type: cvbdm |
| 0431 |  | 4-1/8 x 1 | Moulding 29/08...T-51
$95 set up Type: crwnm |
| 0582 |  | 4-1/8 x 1-1/2 | Moulding 149/11...T-50
$95 set up Type: crwnm |
| 0633 |  | 4-1/8 x 3/4 | symmetrical
Moulding 39/09...T-58
$50 set up Type: chrrm |
| 0872 |  | 4-1/8 x 1-1/2 | Moulding 55/02...T-80
$60 set up Type: custo |
| 1270 |  | 4-1/8 x 3/4 | Moulding 84/02...T-109
edge bead
$50 set up Type: casin |
| 1412 |  | 4-1/8 x 13/16 | Moulding 93/10...T-137
dentil
$95 set up Type: crwnm |
| 1447 |  | 4-1/8 x 7/8 | Moulding 98/02...T-128
price 5/4 stock
$95 set up Type: crwnm |
| 1536 |  | 4-1/8 x 1-1/8 | Moulding 104/09...T-147
$95 set up Type: crwnm |
| 1537 |  | 4-1/8 x 3/4 | Moulding 104/10...T-148
$95 set up Type: crwnm |
| 1615 |  | 4-1/8 x 3/4 | Moulding 110/13...T-155
dentil
$95 set up Type: crwnm |
| 1673 |  | 4-1/8 x 3/4 | Moulding 115/06...T-161,64
$95 set up Type: crwnm |
| 1883 |  | 4-1/8 x 1 | Moulding 133/01...T-184
$50 set up Type: casin |
| 2061 |  | 4-1/8 x 5/8 | Moulding 154/15...T-195
$95 set up Type: crwnm |
| 2112 |  | 4-1/8 x 1 | Moulding 158/13...T-202
$95 set up Type: crwnm |
| 0610 |  | 4-3/16 x 11/16 | slightly different from the basic 4-1/4" crown we keep in s t o c k
Moulding 38/03...T-58
$95 set up Type: crwnm |
| 2111 |  | 4-3/16 x 1/2 | Moulding 158/12...T-203
$95 set up Type: crwnm |
| 0345 |  | 4-1/4 x 1-1/4 | Moulding 23/13...T-28
$95 set up Type: crwnm |
| 0433 |  | 4-1/4 x 1-1/4 | Moulding 29/10...T-27
$95 set up Type: crwnm |
| 0611 |  | 4-1/4 x 9/16 | slightly differnt than the basic 4-1/4" crown we keep in s t o c k
Moulding 38/04...T-58
$95 set up Type: crwnm |
| 0617 |  | 4-1/4 x 1-1/4 | Moulding 38/10...T-58 and T-60
$80 set up Type: bbrdm |
| 0689 |  | 4-1/4 x 13/16 | Moulding 42/09...T-64
$95 set up Type: crwnm |
| 0837 |  | 4-1/4 x 2-1/8 | symmetrical
Moulding 52/08...T-80
$50 set up Type: crndm |
| 0927 |  | 4-1/4 x 15/16 | Moulding 59/07...T-89
$95 set up Type: crwnm |
| 0972 |  | 4-1/4 x 1-1/16 | Moulding 62/08...T-92
$95 set up Type: cvbdm |
| 1067 |  | 4-1/4 x 7/8 | Moulding 70/08...T-97
$50 set up Type: casin |
| 1281 |  | 4-1/4 x 1-1/2 | Moulding 85/01...T-118
$130 set up, can specify dado Type: hrail |
| 1297 |  | 4-1/4 x 15/16 | Moulding 86/03...T-122
$75 set up Type: casin |
| 1300 |  | 4-1/4 x 3/4 | Moulding 86/06...T-118
$50 set up. add $20 for relief Type: chrrm |
| 1333 |  | 4-1/4 x 2 | Moulding 88/03...T-132
$60 set up Type: chrrm |
| 1441 |  | 4-1/4 x 3/4 | Moulding 97/05...T-138
$60 set up Type: bbrdm |
| 1541 |  | 4-1/4 x 3/4 | Moulding 105/02...T-150
$60 set up Type: bbrdm |
| 1652 |  | 4-1/4 x 13/16 | Moulding 114/02...T-161
$75 set up Type: casin |
| 1677 |  | 4-1/4 x 3/4 | Moulding 115/10...T-161
$95 set up Type: crwnm |
| 1762 |  | 4-1/4 x 1-3/4 | Moulding 122/05...T-171
$75 set up Type: chrrm |
| 2004 |  | 4-1/4 x 3/4 | Moulding 162/03...T-206
$60 set up Type: casin |
| 2049 |  | 4-1/4 x 1-1/16 | Moulding 154/03...T-195
$50 set up Type: casin |
| 2065 |  | 4-1/4 x 1-1/4 | Moulding 155/04...T-195
$50 set up Type: chrrm |
| 2102 |  | 4-1/4 x 15/16 | Moulding 158/03...T-201
$50 set up Type: casin |
| 2134 |  | 4-1/4 x 1 | Moulding 160/06...T-204
$50 set up Type: casin |
| 0263 |  | 4-5/16 x 3/4 | Moulding 20/02...T-37
$60 set up
add $20 for dado Type: bbrdm |
| 0266 |  | 4-5/16 x 1 | Moulding 20/03...T-37
beads
$50 set up Type: casin |
| 0162 |  | 4-3/8 x 13/16 | extreme bed
Moulding 13/04...T-18
$95 set up Type: cvbdm |
| 0347 |  | 4-3/8 x 5/8 | Moulding 150/14...T-28
aka BMC15
$95 set up Type: crwnm |
| 0429 |  | 4-3/8 x 13/16 | Moulding 146/09...T-20
$95 set up Type: crwnm |
| 0534 |  | 4-3/8 x 1-1/2 | Moulding 34/12...T-57
$60 set up Type: cvbdm |
| 0609 |  | 4-3/8 x 5/8 | Moulding 38/02...T-58
$95 set up Type: crwnm |
| 0874 |  | 4-3/8 x 3/4 | fluted casing, symmetrical
Moulding 55/04...T-82
$50 set up Type: casin |
| 1069 |  | 4-3/8 x 9/16 | Moulding 70/10...T-98
$60 set up
similar to B-12 Type: bbrdm |
| 1094 |  | 4-3/8 x 1 | Symmetrical
Moulding 73/01...T-101
$50 set up Type: chrrm |
| 1427 |  | 4-3/8 x 1 | Moulding 95/07...T-132
$50 set up
similar to some B-11's Type: bbrdm |
| 1432 |  | 4-3/8 x 13/16 | Moulding 96/06...T-127
$60 set up
add $20 for dado Type: bbrdm |
| 1543 |  | 4-3/8 x 1/2 | Moulding 105/04...T-149
$60 set up Type: bbrdm |
| 1605 |  | 4-3/8 x 11/16 | Moulding 110/03...T-156
$60 set up
add $20 for dado Type: bbrdm |
| 1843 |  | 4-3/8 x 13/16 | Moulding 129/13...T-182
$95 set up Type: cvbdm |
| 2034 |  | 4-3/8 x 11/16 | Moulding 152/10...T-196
$95 set up Type: crwnm |
| 2101 |  | 4-3/8 x 7/16 | Moulding 158/02...T-201
$60 set up Type: bbrdm |
| 0077 |  | 4-7/16 x 1-1/16 | A two-piece casing for very old homes
Moulding 06/03...T-45
two set-ups, $75 and $50 Type: casin |
| 0112 |  | 4-1/2 x 1-1/2 | aka mantle mold
Moulding 09/12...T-7
aka MM1
$60 set up Type: miscm |
| 0126 |  | 4-1/2 x 3/8 | symmetrical
Moulding 08/12...T-16
$95 set up Type: chrrm |
| 0180 |  | 4-1/2 x 3/4 | Moulding 11/08...T-9,89
$80 set up...three knives Type: bbrdm |
| 0285 |  | 4-1/2 x 1-1/8 | Moulding 20/10...T-25
$60 set up Type: bbrdm |
| 0323 |  | 4-1/2 x 13/16 | Moulding 22/14...T-37
$115 set up, four knives Type: crwnm |
| 0350 |  | 4-1/2 x 1-1/16 | Moulding 146/11...T-29
$95 set up Type: crwnm |
| 0490 |  | 4-1/2 x 5/8 | tall B-8 baseboard, cheaper without the dado in the back
Moulding 32/12...T-57
$60 set up
add $20 for dado
Type: bbrdm |
| 0559 |  | 4-1/2 x 1-1/2 | Moulding 35/13...T-52
edge bead
$75 set up Type: casin |
| 0570 |  | 4-1/2 x 1 | Moulding 36/01...T-52
$95 set up Type: crwnm |
| 0597 |  | 4-1/2+ x 5/8 | can accept 1/2" rope in slot
Moulding 37/08...T-25, T-50
$75 set up Type: bbrdm |
| 0599 |  | 4-1/2 x 5/8 | Moulding 37/10...T-52
$50 set up Type: casin |
| 0679 |  | 4-1/2+ x 3/4 | Moulding 141/01...T-66
$60 set up
add $20 for dado Type: bbrdm |
| 0680 |  | 4-1/2+ x 3/4 | Moulding 140/02...T-66
$60 set up Type: bbrdm |
| 0683 |  | 4-1/2+ x 1-1/8 | Moulding 42/03...T-63
$85 set up Type: bbrdm |
| 0701 |  | 4-1/2 x 1-1/16 | Moulding 43/08...T-44
$60 set up
a.k.a. B11
Also used to make C11
add $20 for dado Type: bbrdm |
| 0717 |  | 4-1/2 x 3/4 | Moulding 44/10...T65
$95 set up Type: crwnm |
| 0735 |  | 4-1/2 x 9/16 | Moulding 49/01...T-10
$50 set up
Aka: B12, LB11 Type: bbrdm |
| 0764 |  | 4-1/2 x 1/2 | Moulding 50/04...T-75
$60 set up Type: bbrdm |
| 0773 |  | 4-1/2+ x 1 | Moulding 45/01...T-65
$60 set up Type: bbrdm |
| 0816 |  | 4-1/2 x 9/16 | b-12 baseboard
Moulding 51/03...T-10
$50 set up Type: bbrdm |
| 0867 |  | 4-1/2 x 1-1/8 | Moulding 54/09...T-80
$60 set up Type: bbrdm |
| 0873 |  | 4-1/2 x 3/4 | Moulding 55/03...T-77
$50 set up Type: casin |
| 0888 |  | 4-1/2 x 1-1/16 | Moulding 56/03...T-82
$50 set up
add $20 for dado Type: casin |
| 0891 |  | 4-1/2 x 1 | Chavez custom similar to B11.
Moulding 45/01...T-65
$60 set up
add $20 for dado Type: bbrdm |
| 0921 |  | 4-1/2 x 3/4 | Moulding 59/02...T-87
$95 set up Type: panlm |
| 0966 |  | 4-1/2 x 5/8 | Moulding 62/02...T-94?
$60 set up Type: bbrdm |
| 0971 |  | 4-1/2 x 1 | symmetrical
Moulding 62/07...T-87
$95 set up Type: cvbdm |
| 1060 |  | 4-1/2 x 1-3/4 | used as a plinth block
Moulding 70/01...T-98
$50 set up Type: casin |
| 1085 |  | 4-1/2 x 1/2 | Moulding 72/03...T-110
center bead
$50 set up Type: bbrdm |
| 1103 |  | 4-1/2 x 3/4 | Moulding 73/10...T-105
$75 set up Type: chrrm |
| 1142 |  | 4-1/2 x 1-1/2 | this is a negative for cast stone work
Moulding 74/04...T-98
$75 set up Type: miscm |
| 1211 |  | 4-1/2 x 13/16 | Moulding 80/02...T-125
$60 set up Type: bbrdm |
| 1429 |  | 4-1/2 x 3/4 | Moulding 96/03...T-66
$60 set up Type: bbrdm |
| 1489 |  | 4-1/2 x 3/4 | Moulding 100/09...T-143
$95 set up Type: crwnm |
| 1492 |  | 4-1/2 x 11/16 | Moulding 101/02...T-144
$60 set up
add $20 for dado Type: bbrdm |
| 1620 |  | 4-1/2 x 5/8 | Moulding 111/04...T-154
$60 set up Type: bbrdm |
| 1630 |  | 4-1/2 x 1-1/2 | Moulding 112/02...T-157
$60 set up Type: casin |
| 1642 |  | 4-1/2 x 3/4 | Moulding 113/04...T-159
$75 et up Type: casin |
| 1680 |  | 4-1/2 x 1-5/8 | Moulding 116-02...T-163
$75 set up Type: casin |
| 1702 |  | 4-1/2 x 13/16 | Moulding 117/08...T-164
$60 set up
Symmetrical Type: chrrm |
| 1721 |  | 4-1/2 x 5/8 | Moulding 119/02...T-166
$60 set up Type: bbrdm |
| 1779 |  | 4-1/2 x 1 | Moulding 124/01...T-192
$60 set up Type: casin |
| 1823 |  | 4-1/2 x 3/4 | Moulding 128/04...T-191
$50 set up
symmetrical Type: casin |
| 1841 |  | 4-1/2 x 9/16 | Moulding 129/14...T-185
$95 set up Type: crwnm |
| 1858 |  | 4-1/2 x 1-1/4 | Moulding 130/14...T-182
$50 set up Type: chrrm |
| 1867 |  | 4-1/2 x 1-1/2 | Moulding 132/01...T-176
$60 set up Type: casin |
| 1998 |  | 4-1/2 x 5/8 | Moulding 161/10...T-204
$60 set up Type: bbrdm |
| 2014 |  | 4-1/2 x 1-1/16 | Moulding 151/02...T-81
see bd 56/06 too
$60 set up Type: bbrdm |
| 0719 |  | 4-9/16 x 13/16 | Moulding 140/10...T-66
$95 set up
Type: crwnm |
| 0963 |  | 4-9/16 x 13/16 | Moulding 61/12...T-86
$95 set up Type: cvbdm |
| 1737 |  | 4-9/16 x 1 | Moulding 120/01...T-167
$60 set up Type: casin |
| 1797 |  | 4-9/16 x 1-9/16 | Moulding 126/01...T-186
$75 set up Type: casin |
| 0104 |  | 4-5/8 x 1 | aka B422 & C422
Moulding 09/05...T-2
$50 set up Type: bbrdm |
| 0574 |  | 4-5/8 x 13/16 | Moulding 36/05...T-53
$95 set up Type: crwnm |
| 0812 |  | 4-5/8 x 1-1/4 | a very nice deep crown
Moulding 47/12...T-72
$95 set up Type: crwnm |
| 1488 |  | 4-5/8 x 3/4 | Moulding 100/08...T-
$95 set up
fruit Type: crwnm |
| 1603 |  | 4-5/8 x 3/4 | Moulding 110/01...T-156
$75 set up Type: bbrdm |
| 1621 |  | 4-5/8 x 13/16 | Moulding 111/05...T-157
$50 set up Type: bbrdm |
| 1678 |  | 4-5/8 x 1-1/4 | Moulding 115/11...T-161
very large bed
$95 set up
Type: cvbdm |
| 1756 |  | 4-5/8 x 13/16 | Moulding 121/12...T-170
$95 set up Type: crwnm |
| 2026 |  | 4-5/8 x 3/4 | Moulding 152/02...T-196
$60 set up
add $20 for dado Type: bbrdm |
| 0352 |  | 4-11/16 x 5/8 | Moulding 146/10...T-32
aka BMC595
$95 set up Type: crwnm |
| 0054 |  | 4-3/4 x 1-1/2 | Moulding 04/03...T-5
$50 set up Type: casin |
| 0533 |  | 4-3/4 x 3/8 | Moulding 34/11...T-48
$95 set up Type: sidin |
| 0608 |  | 4-3/4 x 3/4 | Moulding 38/01...T-58
$95 set up Type: crwnm |
| 0703 |  | 4-3/4 x 1-1/4 | Moulding 43/10...T-59
$50 set up Type: bbrdm |
| 0898 |  | 4-3/4 x 13/16 | Moulding 57/04...T-79
$95 set up Type: crwnm |
| 0983 |  | 4-3/4 x 13/16 | Moulding 63/06...T-91
$95 set up Type: crwnm |
| 1049 |  | 4-3/4 x 1-1/2 | Moulding 69/01...T-103
$60 set up Type: casin |
| 1050 |  | 4-3/4 x 1 | Moulding 69/02...T-108
$50 set up Type: casin |
| 1112 |  | 4-3/4 x 3/4 | Moulding 66/07...T-111
$95 set up Type: crwnm |
| 1180 |  | 4-3/4 x 1-5/8 | Moulding 77/08...T-119
$75 set up Type: casin |
| 1267 |  | 4-3/4 x 7/8 | Moulding 83/13...T-112
Price 5/4 stock
$95 set up Type: crwnm |
| 1418 |  | 4-3/4 x 1-1/4 | Moulding 94/06...T-137
$95 set up Type: crwnm |
| 1579 |  | 4-3/4 x 3/4 | Moulding 108/03...T-154
$60 set up Type: bbrdm |
| 1787 |  | 4-3/4 x 3/4 | Moulding 125/01...T-189
$60 set up Type: bbrdm |
| 1810 |  | 4-3/4 x 3/4 | Moulding 127/02...T-187
$60 set up Type: bbrdm |
| 1869 |  | 4-3/4 x 13/16 | Moulding 132/03...T-13,185
$75 set up Type: casin |
| 1882 |  | 4-3/4 x 1-3/4 | Moulding 132/16...T-184
$95 set up
symmetrical Type: cvbdm |
| 0193 |  | 4-7/8 x 7/8 | Moulding 14/09...T-6
$50 set up
Symmetrical Type: custo |
| 0276 |  | 4-7/8 x 1-1/8 | Moulding 141/11...T-24
$95 set-up Type: crwnm |
| 0387 |  | 4-7/8 x 13/16 | Moulding 150/16...T-30
$95 set up
susan fruit Type: crwnm |
| 0696 |  | 4-7/8 x 3/4 | Moulding 43/03...T-61
$50 set up Type: bbrdm |
| 0741 |  | 4-7/8 x 1-13/16 | Moulding 49/07...T-74
$115 set up Type: crwnm |
| 0944 |  | 4-7/8 x 3/4 | Moulding 60/11...T-95
$95 set up Type: crwnm |
| 0984 |  | 4-7/8 x 13/16 | Moulding 63/07...T-91
$95 set up Type: crwnm |
| 1031 |  | 4-7/8 x 1-3/16 | Moulding 67/02...T-107
$95 set up Type: crwnm |
| 1166 |  | 4-7/8 x 1 | This is an example of any sized dado, any orientation, or any roundover
Moulding 75/12...T-111
$95 set up Type: miscm |
| 1446 |  | 4-7/8 x 1-11/16 | Moulding 98/01...T-130
$95 set up Type: crwnm |
| 1450 |  | 4-7/8 x 1-1/4 | Moulding 98/05...T-133
$95 set up Type: crwnm |
| 1525 |  | 4-7/8 x 1 | Moulding 103/07...T-148
$50 set up Type: chrrm |
| 1990 |  | 4-7/8 x 1-1/8 | Moulding 161/02...T-206
$60 set up Type: bbrdm |
| 0055 |  | 5+ x 1-1/4 | Moulding 04/04...T-5
one bead
$60 set up
add $20 for dado Type: bbrdm |
| 0225 |  | 5+ x 3/4 | Two pc moulding for old style house trim
Moulding 17/03...T-42
set up $75 each piece Type: bbrdm |
| 0226 |  | 5 x 5/8 | Moulding 18/01...T-26
$50 set up Type: bbrdm |
| 0271 |  | 5 x 1-1/4 | Moulding 19/13...T-24
$60 set up
symmetrical Type: custo |
| 0306 |  | 5 x 1-7/16 | Moulding 148/17...T-25
$95 set up Type: crwnm |
| 0413 |  | 5+ x 3/4 | Moulding 29/01...T-20
$85 set up (3 Knives) Type: bbrdm |
| 0415 |  | 5+ x 13/16 | Moulding 28/03...T-34
$60 set up Type: bbrdm |
| 0416 |  | 5+ x 3/4 | Moulding 28/04...T-34
$60 set up Type: bbrdm |
| 0425 |  | 5+ x 5/8 | Moulding 147/01...T-41
$60 set up Type: bbrdm |
| 0523 |  | 5+ x 1 | Moulding 34/01...T-48
a.k.a. MC-569
5": $50.00 set up
5"+: $75.00 set up Type: bbrdm |
| 0524 |  | 5+ x 11/16 | Moulding 34/02...T-56
$50 set up Type: bbrdm |
| 0650 |  | 5+ x 1 | Moulding 40/03...T-59
$60 set up
Type: bbrdm |
| 0665 |  | 5+ x 3/4 | Moulding 41/08...T-63
$60 set up Type: bbrdm |
| 0786 |  | 5 x 15/16 | Moulding 142/13...T-70
$95 set up
price 5/4 stock Type: crwnm |
| 0792 |  | 5 x 1 | can't come to points on the edges...1/16" edges
symmetrical
Moulding 46/05...T-69
$75 set up Type: miscm |
| 0844 |  | 5 x 1-1/2 | wall cap, symmetrical
Moulding 53/01...T-79
$50 set up Type: hrail |
| 0845 |  | 5 x 1-1/2 | wall cap, symmetrical
Moulding 53/02...T-83
$50 set up Type: hrail |
| 0919 |  | 5 x 13/16 | Moulding 58/12...T-90
$95 set up Type: cvbdm |
| 0965 |  | 5+ x 3/4 | shown with scribing dado on bottom.
Moulding 62/01...T-3
large bead
$60 set up add $20 for dado Type: bbrdm |
| 0981 |  | 5 x 3/8 | similates shutter louviers
Moulding 63/04...T-94
$50 set up Type: sidin |
| 0992 |  | 5 x 3/4 | Moulding 64/02...T-91
$60 set up Type: bbrdm |
| 1035 |  | 5 x 1 | Moulding 67/06...T-108
$95 set up Type: crwnm |
| 1077 |  | 5+ x 5/8 | Moulding 71/04...T-106
$60 set up Type: bbrdm |
| 1078 |  | 5+ x 3/4 | Moulding 71/05...T-104
$60 set up Type: bbrdm |
| 1079 |  | 5+ x 3/4 | Moulding 71/06...T-101
$60 set up Type: bbrdm |
| 1083 |  | 5+ x 3/4 | Moulding 72/01...T-109
$60 set up Type: bbrdm |
| 1084 |  | 5+ x 3/4 | Moulding 72/02...T-104
$60 set up Type: bbrdm |
| 1100 |  | 5 x 3/4 | Moulding 73/07...T-102
$50 set up
symmetrical Type: chrrm |
| 1107 |  | 5 x 1-1/2 | Moulding 66/02...T-110
$95 set up Type: crwnm |
| 1309 |  | 5 x 1-3/16 | Moulding 77/10...T-123
$95 set up Type: cvbdm |
| 1185 |  | 5 x 1 | Moulding 78/05...T-124
$60 set up Type: casin |
| 1209 |  | 5 x 13/16 | Moulding 79/16...T-125
$95 set up Type: crwnm |
| 1213 |  | 5 x 3/4 | Moulding 80/04...T-112
$60 set up Type: bbrdm |
| 1223 |  | 5 x 3/4 | Moulding 81/02...T-115
two beads
$60 set up Type: bbrdm |
| 1264 |  | 5 x 3 | Moulding 83/10...T-118, T-102
$150 set up, add .90 per foot to run three times
symmetrical
dado can be specified Type: hrail |
| 1331 |  | 5 x 3/4 | Moulding 88/01...T136
$75 set up, $50 w/out relief
symmetrical, beads Type: casin |
| 1405 |  | 5 x 7/8 | Moulding 93/03...T-131
$95 set up Type: crwnm |
| 1424 |  | 5 x 3/4 | Moulding 95/04...T-135
$60 set up Type: bbrdm |
| 1431 |  | 5 x 3/4 | Moulding 96/05...T-125
$60 set up Type: bbrdm |
| 1562 |  | 5 x 13/16 | Moulding 106/10...T-150
$95 set up Type: crwnm |
| 1573 |  | 5 x 11/16 | Moulding 107/10...T-152
$60 set up, add .30/lf to run twice
symmetrical Type: chrrm |
| 1616 |  | 5 x 1 | Moulding 110/14...T-156
$95 set up Type: crwnm |
| 1637 |  | 5 x 1 | Moulding 112/09...T-158
$95 set up Type: crwnm |
| 1651 |  | 5 x 3/4 | Moulding 114/01...T-160
$60 set up Type: bbrdm |
| 1667 |  | 5 x 3/4 | Moulding 114/17...T-160
$95 set up Type: crwnm |
| 1674 |  | 5 x 5/8 | Moulding 115/07...T-162
$95 set up Type: crwnm |
| 1706 |  | 5 x 3/4 | Moulding 118/01...T-165
$60 set up Type: bbrdm |
| 1784 |  | 5 x 1-1/8 | Moulding 124/06...T-192
$95 set up Type: crwnm |
| 2013 |  | 5+ x 13/16 | Moulding 151/01...T-196
$60 set up without relief Type: bbrdm |
| 2063 |  | 5 x 1-5/16 | Moulding 155/02...T-199
$50 set up Type: casin |
| 2093 |  | 5 x 3/4 | Moulding 157/03...T-201
symmetrical, $50 set up Type: casin |
| 2103 |  | 5 x 9/16 | Moulding 158/04...T-202
$60 set up Type: bbrdm |
| 2113 |  | 5+ x 3/4 | Moulding 159/01...T-203
$60 set up Type: bbrdm |
| 2131 |  | 5 x 1-1/4 | Moulding 160/03...T-205
$50 set up Type: crndm |
| 2136 |  | 5 x 1-1/16 | Moulding 160/08...T-205
t up Type: crwnm |
| 0505 |  | 5-1/16 x 11/16 | Very unique siding. It appears to be curved planks side by side by side.
Moulding 33/05...T-57
$95 set up Type: sidin |
| 0028 |  | 5-1/8 x 1-3/4 | wall cap, symmetrical
Moulding 01/09...T-19
$110 set up Type: hrail |
| 0134 |  | 5-1/8 x 1-3/8 | Simulated log cabin siding
Moulding 12/02...T-16
$75 set up Type: sidin |
| 0238 |  | 5-1/8 x 5/8 | Moulding 18/06...T-
$95 set up Type: crwnm |
| 0518 |  | 5-1/8 x 3/4 | Moulding 143/16...T-55
$110 set up Type: crwnm |
| 0767 |  | 5-1/8 x 2-5/8 | Moulding 50/07...T-76
$80 set up Type: crndm |
| 1308 |  | 5-1/8 x 1-3/16 | Moulding 77/11...T-123
use 6/4 stock
$95 set up Type: crwnm |
| 1481 |  | 5-1/8 x 3/4 | Moulding 100/01...T-144
$60 set up Type: bbrdm |
| 1482 |  | 5-1/8 x 1/2 | Moulding 100/02...T-144
$60 set up Type: bbrdm |
| 1508 |  | 5-1/8 x 1-9/16 | Moulding 102/04...T-115 Type: chrrm |
| 1554 |  | 5-1/8 x 5/8 | Moulding 106/02...T-151
$60 set up Type: bbrdm |
| 2071 |  | 5-1/8 x 1-1/16 | Moulding 155/10...T-198
$95 set up
add $.30 per foot to run twice Type: crwnm |
| 1334 |  | 5-3/16 x 1-1/16 | Moulding 88/04...T-142
$60 set up Type: chrrm |
| 0026 |  | 5-1/4 x 1-3/8 | Moulding 01/07...T-22
aka bmc-50, bmc50
$125.00 set up
add $.60 per foot to run it twice....quote 8/4 price Type: cvbdm |
| 0208 |  | 5-1/4 x 1-3/8 | bar rail
Moulding 16/04...T-39
$120 set-up
price 8/4 stock
3/4 x 2-5/8 offset
Type: miscm |
| 0296 |  | 5-1/4 x 3/4 | wide casing in older homes, used with rosettes usually.
symmetrical
Moulding 21/04...T-31
$60 set up Type: casin |
| 0305 |  | 5-1/4 x 13/16 | Moulding 142/12...T-37
$100 set up Type: crwnm |
| 0339 |  | 5-1/4 x 13/16 | very old style used with rosettes on corners
symmetrical, beads
Moulding 23/09...T-28
$50 setup Type: casin |
| 0353 |  | 5-1/4 x 9/16 | aka tall colonial base
Moulding 148/01...T-28
aka LSB9
$60 set up Type: bbrdm |
| 0535 |  | 5-1/4+ x 9/16 | Moulding 142/02...T-55
$60 set up
add $20 for dado Type: bbrdm |
| 0691 |  | 5-1/4 x 7/8 | Moulding 145/10...T-64
$95 set up Type: crwnm |
| 0692 |  | 5-1/4 x 3/4 | Moulding 145/11...T-63
$95 set up Type: crwnm |
| 0718 |  | 5-1/4 x 13/16 | Moulding 44/11...T-
$95 set up Type: crwnm |
| 0806 |  | 5-1/4 x 1 | a large 3 step casing or can be a base too.
Moulding 47/06...T-72
$50 set up Type: casin |
| 0814 |  | 5-1/4 x 3/4 | Similar appearance as 105 siding but this has tounge and groove
Moulding 51/01...T-
$110 set up Type: sidin |
| 0920 |  | 5-1/4 x 3/4 | symmetrical
Moulding 59/01...T-91
beads
$60 set up Type: casin |
| 0991 |  | 5-1/4+ x 3/4 | single bead at joints of siding
Moulding 64/01...T-92
$110 set up Type: sidin |
| 1039 |  | 5-1/4 x 5/8 | Center has dado to accept carved section...camcraft
Moulding 68/03...T-99
$95 set up Type: crwnm |
| 1183 |  | 5-1/4 x 1-7/16 | Another log cabin type siding, a little different that the one above
Moulding 78/03...T-116
$75 set up Type: sidin |
| 1191 |  | 5-1/4 x 1-1/2 | Moulding 78/11...T-116
$125 set up, add .60 per foot to run twice. Type: cvbdm |
| 1192 |  | 5-1/4 x 1-1/2 | Moulding 79/01...T-119
$95 set up, add .50 to run twice
symmetrical Type: hrail |
| 1212 |  | 5-1/4 x 3/4 | Moulding 80/03...T-113
$60 set up Type: bbrdm |
| 1222 |  | 5-1/4 x 13/16 | Moulding 81/01...T-113
$60 set up Type: bbrdm |
| 1255 |  | 5-1/4 x 9/16 | Moulding 83/01...T-121
$60 set up Type: bbrdm |
| 1414 |  | 5-1/4 x 13/16 | Moulding 94/02...T-141
$75 set up Type: crwnm |
| 1428 |  | 5-1/4 x 1 | Moulding 96/02...T-66
$50 set up Type: miscm |
| 1430 |  | 5-1/4 x 9/16 | Moulding 96/04...T-137
$60 set up Type: bbrdm |
| 1696 |  | 5-1/4 x 5/8 | Moulding 117/02...T-164
$75 set up Type: bbrdm |
| 1736 |  | 5-1/4 x 1-1/2 | Moulding 119/17...T-167
$125 set up Type: hrail |
| 1739 |  | 5-1/4 x 13/16 | Moulding 120/03...T-168
$95 set up Type: crwnm |
| 1812 |  | 5-1/4 x 5/8 | Moulding 127/04...T-189
$60 set up Type: bbrdm |
| 1818 |  | 5-1/4 x 1-1/2 | Moulding 127/10...T-187
$125 set up
add $.60 per foot to run three times Type: cvbdm |
| 1962 |  | 5-1/4 x 1-1/2 | Moulding 137/18...T-175
$95 set up add $.30 to run twice Type: crwnm |
| 2021 |  | 5-1/4 x 3/4 | Moulding 151/09...T-8
$95 set up Type: sidin |
| 2028 |  | 5-1/4 x 5/8 | Moulding 152/04...T-196
beaded lap siding
$85 set up Type: sidin |
| 0105 |  | 5-3/8 x 1-7/16 | wall rail mounted with brackets or to another board
Moulding 143/04...T-6, T-10
$95 set up Type: hrail |
| 0246 |  | 5-3/8 x 3/4 | 1 x 6, 5-1/8 net face. Beaded
Moulding 147/03...T-33
$95 set up Type: sidin |
| 0344 |  | 5-3/8 x 3/4 | 5" tear-dropped siding
Moulding 24/05...T-32
this one has to come from 4/4" stock
$75 set up Type: sidin |
| 0386 |  | 5-3/8 x 11/16 | Moulding 26/12...T-36
$60 set up Type: bbrdm |
| 0438 |  | 5-3/8 x 1-1/4 | A dentil or rope mould may be added to the flat spot on this moulding. Dentils and ropes are available in house.aka BMC-40
Moulding 146/12...T-51
$95 set up Type: crwnm |
| 0440 |  | 5-3/8 x 1 | Moulding 148/16...T-27
$95 set up Type: crwnm |
| 0791 |  | 5-3/8 x 1-1/2 | symmetrical handrail
Moulding 46/04...T-71
$95 set up, add $.60/lf for running twice Type: hrail |
| 0897 |  | 5-3/8 x 1-1/16 | very vertical crown
Moulding 57/03...T-81
$95 set up Type: crwnm |
| 0906 |  | 5-3/8 x 1-1/8 | Moulding 58/01...T-89
$50 set up Type: casin |
| 1113 |  | 5-3/8 x 5/8 | Moulding 66/08...T-109
$95 set up Type: crwnm |
| 1181 |  | 5-3/8 x 11/16 | Moulding 78/01...T-123
$75 set up
This one can come from a 1 x 6. Type: sidin |
| 1439 |  | 5-3/8 x 3/4 | Moulding 97/03...T-138
$60 set up
add $20 for dado Type: bbrdm |
| 1585 |  | 5-3/8 x 1 | Moulding 108/09...T-152
$95 set up Type: crwnm |
| 1586 |  | 5-3/8 x 1 | Moulding 108/10...T-152
$95 set up Type: crwnm |
| 1602 |  | 5-3/8 x 15/16 | Moulding 109/15...T-153
$95 set up Type: crwnm |
| 1770 |  | 5-3/8 x 1-1/16 | Moulding 122/13...T-170
Symmetrical
$95 set up Type: cvbdm |
| 1817 |  | 5-3/8 x 5/8 | Moulding 127/09...T-189
$95 set up Type: crwnm |
| 2029 |  | 5-3/8 x 9/16 | Moulding 152/05...T-197
$95 set up Type: sidin |
| 0086 |  | 5-1/2 x 11/16 | 105 siding
Moulding 06/08...T-15
$85 set up Type: sidin |
| 0095 |  | 5-1/2 x 11/16 | This is a wide fluted moulding used with large rosettes. It can be wider or narrower if needed.
You are able to order the rosettes to match any patters.
symmetrical
moulding 07/10...T-2
aka LS fluted pilaster
$50 set up Type: casin |
| 0174 |  | 5-1/2 x 1-1/8 | this is just a portion of a wide fluted moulding up to 9" wide
Moulding 11/04...T-11
$75 set up Type: casin |
| 0157 |  | 5-1/2+ x 11/16 | Moulding 12/07...T-44
$60 set up Type: bbrdm |
| 0195 |  | 5-1/2 x 13/16 | Typical large crown
Moulding 14/11...T-45
$95 set up Type: crwnm |
| 0197 |  | 5-1/2 x 5/8 | Moulding 14/12...T-21
similar to B514
$60 set up
Type: bbrdm |
| 0337 |  | 5-1/2 x 3/4 | This is a very wide casing for older houses.
symmetrical
Moulding 23/08...T-32
$50 set up Type: casin |
| 0354 |  | 5-1/2 x 1-3/8 | Moulding 145/09...T-29
$95 set up
susan fruit Type: cvbdm |
| 0383 |  | 5-1/2 x 1/2 | 5-1/4" net face coverage
Moulding 26/09...T-36
$95 set up Type: sidin |
| 0412 |  | 5-1/2 x 3/4 | casing for very old houses, normally used with rosettes.
symmetrical
beaded
Moulding 28/02...T-34
$60 set up Type: casin |
| 0475 |  | 5-1/2 x 3/4 | Moulding 140/05...T-51
$95 set up, specify widths, usually varying.
$85 set up Type: sidin |
| 0532 |  | 5-1/2 x 9/16 | This is a wide version of the 3-3/8 fluted casing.
symmetrical
Moulding 34/10...T-48
$50 set up
Type: casin |
| 0785 |  | 5-1/2 x 1-3/16 | Moulding 147/11...T-69
$125
set up
add $.60 per foot to run it twice Type: crwnm |
| 0832 |  | 5-1/2 x 9/16 | tall b-10 baseboard
Moulding 52/03...T-77
$60 set up
add $20 for dado Type: bbrdm |
| 0860 |  | 5-1/2 x 3/4 | Moulding 54/02...T-81
$60 set up Type: bbrdm |
| 0890 |  | 5-1/2 x 11/16 | Moulding 56/05...T-85
$75 set up Type: bbrdm |
| 0925 |  | 5-1/2 x 3/4 | symmetrical
Moulding 59/06...T-88
$60 set up Type: casin |
| 1006 |  | 5-1/2 x 3/4 | symmetrical, beads
Moulding 65/02...T-66
$60 set up Type: casin |
| 1106 |  | 5-1/2 x 1-1/4 | Moulding 66/01...T-104
$50 set up Type: crwnm |
| 1110 |  | 5-1/2 x 3/4 | dado to accept dentil
Moulding 66/05...T-111
$95 set up Type: crwnm |
| 1155 |  | 5-1/2 x 3/4 | Very nice unique siding
Moulding 75/01...T-100
$95 set up Type: sidin |
| 1210 |  | 5-1/2 x 9/16 | Moulding 80/01...T-113
$60 set up
add $20 for relief on bottom Type: bbrdm |
| 1332 |  | 5-1/2 x 1-1/4 | Moulding 88/02...T-136
$50 set up Type: chrrm |
| 1376 |  | 5-1/2 x 9/16 | Moulding 91/05...T-133
Simulated louviers
$50 set up Type: sidin |
| 1377 |  | 5-1/2 x 1/2 | Moulding 91/06...T-127
$95 set up Type: sidin |
| 1378 |  | 5-1/2 x 3/4 | Moulding 91/07...T-138
lap siding
$75 set up Type: sidin |
| 1423 |  | 5-1/2 x 13/16 | Moulding 95/03...T-100
$60 set up Type: bbrdm |
| 1426 |  | 5-1/2 x 9/16 | Moulding 95/06...T-135
$85 set up Type: bbrdm |
| 1486 |  | 5-1/2 x 3/4 | Moulding 100/06...T-144
$60 set up Type: bbrdm |
| 1564 |  | 5-1/2 x 3/4 | Moulding 107/01...T-151
$60 set up Type: bbrdm |
| 1622 |  | 5-1/2 x 3/4 | Moulding 111/06...T-155
$60 set up, $80 with dado Type: bbrdm |
| 1640 |  | 5-1/2 x 3/4 | Moulding 113/02...T-159
$60 set up Type: bbrdm |
| 1720 |  | 5-1/2 x 3/4 | Moulding 119/01...T-166
$60 set up Type: bbrdm |
| 1738 |  | 5-1/2 x 3/4 | Moulding 120/02...T-168
$60 set up Type: bbrdm |
| 1758 |  | 5-1/2 x 5/8 | Moulding 122/01...T-170
$60 set up Type: bbrdm |
| 1772 |  | 5-1/2 x 1 | Moulding 123/03...T-191
$95 set up Type: bbrdm |
| 1774 |  | 5-1/2 x 1 | Moulding 123/04...T-
$50 set up
add $20 for dado Type: casin |
| 1780 |  | 5-1/2 x 3/4 | Moulding 124/02...T-186
$60 set up Type: bbrdm |
| 1809 |  | 5-1/2 x 1 | Moulding 127/01...T-190
B422 similar
$60 set up Type: bbrdm |
| 1845 |  | 5-1/2 x 1-1/2 | Moulding 130/01...T-178
$110 set up
add $.40 to run twice Type: hrail |
| 1848 |  | 5-1/2 x 1-1/2 | Moulding 130/04...T-174
$60 set up Type: bbrdm |
| 1861 |  | 5-1/2 x 1-1/16 | Moulding 131/03...T-173
$110 set up Type: crwnm |
| 1863 |  | 5-1/2 x 7/8 | Moulding 131/05...T-181
$95 set up Type: crwnm |
| 1864 |  | 5-1/2 x 1-1/8 | Moulding 131/06...T-174
$95 set up Type: crwnm |
| 1911 |  | 5-1/2 x 1-1/2 | Moulding 134/17...T-177
$95 set up Type: cvbdm |
| 1913 |  | 5-1/2 x 1/2 | Moulding 135/01...T-
No image - squared stock w/ face serrated Type: sidin |
| 1963 |  | 5-1/2 x 1-1/8 | MOulding 138/01...T-171
$50 set up Type: casin |
| 1975 |  | 5-1/2 x 9/16 | Moulding 139/02...T-185
$60 set up Type: bbrdm |
| 2032 |  | 5-1/2 x 3/4 | Moulding 152/08...T-196
symmetrical
$50 set up, $75 with dado Type: casin |
| 2072 |  | 5-9/16 x 1 | Moulding 155/11...T-198
$95 set up Type: crwnm |
| 0212 |  | 5-5/8 x 1-5/16 | Moulding 15/10...T-11
$95 set up Type: crwnm |
| 0252 |  | 5-5/8 x 1-3/8 | Moulding 146/07...T-38
$95 set up Type: crwnm |
| 0508 |  | 5-5/8 x 3/4 | Moulding 33/08...T-48
one bead
$60 set up Type: bbrdm |
| 0596 |  | 5-5/8 x 1-3/4 | This is the top half of a very large crown moulding. See CRWNM0612
for the bottom half
Moulding 37/07...T-47
$75 set up
Type: crwnm |
| 0813 |  | 5-5/8 x 13/16 | this is a very nice crown and can be supplemented with a rope or dentil on the flat spot near the bottom
Moulding 47/13...T-71
$95 set up Type: crwnm |
| 1521 |  | 5-5/8 x 3/4 | Moulding 103/03...T-147
$60 set up Type: bbrdm |
| 1676 |  | 5-5/8 x 11/16 | Moulding 115/09...T-162
$95 set up Type: crwnm |
| 1717 |  | 5-5/8 x 1-3/4 | Moulding 118/12...T-166
$95 set up
symmetrical Type: crndm |
| 1808 |  | 5-5/8 x 7/8 | Moulding 126/12...T-186
$95 set up Type: crwnm |
| 1965 |  | 5-5/8 x 1 | Moulding 138/03...T-174
$60 set up Type: bbrdm |
| 0910 |  | 5-11/16 x 1-1/8 | Moulding 58/07...T-89
$125 set up
add .60 per foot Type: cvbdm |
| 0082 |  | 5-3/4 x 13/16 | Moulding 07/03...Dedicated knives
typical t & g siding or flooring
$95 set up Type: sidin |
| 0734 |  | 5-3/4 x 15/16 | this is larger than the 5-1/2 crown and comes from 5/4 stock
Moulding 48/13...T-75
$95 set up Type: crwnm |
| 0739 |  | 5-3/4 x 13/16 | Moulding 49/05...T-73
$95 set up Type: cvbdm |
| 0743 |  | 5-3/4 x 1-3/16 | Moulding 49/09...T-76
$125 set up, add $.50 per lf for running twice Type: cvbdm |
| 1186 |  | 5-3/4 x 1-1/4 | Moulding 78/06...T-124
$60 set up Type: casin |
| 1221 |  | 5-3/4 x 9/16 | Moulding 80/12...T-121
$95 set up Type: crwnm |
| 1403 |  | 5-3/4 x 3/4 | Moulding 93/01...T-141
$95 set up Type: crwnm |
| 1416 |  | 5-3/4 x 3/4 | Moulding 94/04...T-140
$95 set up Type: crwnm |
| 1448 |  | 5-3/4 x 5/8 | Moulding 98/03...T-139
$95 set up Type: crwnm |
| 1490 |  | 5-3/4 x 13/16 | Moulding 100/10...T-145
$95 set up Type: crwnm |
| 1538 |  | 5-3/4 x 1 | Moulding 104/11...T-147
$95 set up Type: crwnm |
| 1555 |  | 5-3/4 x 13/16 | Moulding 106/03...T-149
symmetrical, beaded
$60 set up Type: casin |
| 1617 |  | 5-3/4 x 1-1/16 | Moulding 111/01...T-156
$50 set up
window stool Type: miscm |
| 1618 |  | 5-3/4 x 5/8 | Moulding 111/02...T-157
$60 set up Type: bbrdm |
| 1791 |  | 5-3/4 x 3/4 | Moulding 125/05...T-189
$75 set up
Type: casin |
| 1964 |  | 5-3/4 x 9/16 | Moulding 138/02...T-182
$60 set up Type: bbrdm |
| 0516 |  | 5-13/16 x 1 | Moulding 33/10...T-56
$95 set up Type: crwnm |
| 1491 |  | 5-13/16 x 1-5/8 | Moulding 101/01...T-144
$50 set up Type: bbrdm |
| 0245 |  | 5-7/8 x 2-3/4 | bar rail
Moulding 148/15...T-
$185.00 set-up Type: miscm |
| 1415 |  | 5-7/8 x 1 | Moulding 94/03...T-132
$95 set up Type: crwnm |
| 1631 |  | 5-7/8 x 5/8 | Moulding 112/03..T-158
$60 set up
add $20 for each dado Type: bbrdm |
| 1695 |  | 5-7/8 x 5/8 | Moulding 117/01...T-164
$60 set up Type: bbrdm |
| 1900 |  | 5-7/8 x 1-3/4 | Moulding 134/06...T-177
$50 set up Type: chrrm |
| 2098 |  | 5-7/8 x 1-1/4 | Moulding 157/08...T-200
$75 set up.
top of two part large crown. see crwnm2097 for bottom
Type: crwnm |
| 2135 |  | 5-7/8 x 1 | Moulding 160/07...T-207
$95 set up Type: cvbdm |
| 0130 |  | 6 x 1 | has built in shoe mold
Moulding 10/11...T-14
large bead
$60 set up
add $20 for dado Type: bbrdm |
| 0166 |  | 6 x 1-9/16 | Moulding 13/07...T-19
$95 set up Type: crwnm |
| 0228 |  | 6 x 1-3/4 | wall rail mounted to brackets or 2 x 2's. Overall dimensions are flexible
Moulding 18/02...T-
as shown with all the rounded corners...$150 set up Type: hrail |
| 0372 |  | 6+ x 1-1/8 | a short portion is also used as plinth block
Moulding 140/01...T-43
$60 set up Type: bbrdm |
| 0418 |  | 6 x 1 | Moulding 28/05...T-41
large bead
$60 set up
Type: bbrdm |
| 0420 |  | 6+ x 3/4 | Moulding 28/06...T-43
$60 set up, add $20 for dado Type: bbrdm |
| 0434 |  | 6 x 1-1/2 | symmetrical
Moulding 29/11...T-34 see 57/05 too
Set-up charge is $150.00 because deep 45 degree angles. Add .40 per foot for two passes (deep cutout)
Type: crwnm |
| 0649 |  | 6+ x 1 | Moulding 40/02...T-62
$60 set up Type: bbrdm |
| 0682 |  | 6+ x 3/4 | Moulding 42/02...T-63
one bead
$60 set up Type: bbrdm |
| 0693 |  | 6 x 1-1/4 | dentil
Moulding 149/13...T-65
$95 set up Type: crwnm |
| 0722 |  | 6 x 1 | Moulding 48/01...T-76
$60 set up Type: bbrdm |
| 0859 |  | 6+ x 1 | Moulding 54/01...T-81
$60 set up Type: bbrdm |
| 0886 |  | 6+ x 3/4 | Moulding 56/01...T-82
$60 set up Type: bbrdm |
| 0887 |  | 6+ x 3/4 | Moulding 56/02...T-78
beaded
$80 set up Type: bbrdm |
| 1037 |  | 6 x 1-3/4 | Moulding 68/01...T-108
$60 set up Type: crwnm |
| 1074 |  | 6+ x 3/4 | Moulding 71/01...T-97
$60 set up Type: bbrdm |
| 1075 |  | 6+ x 7/8 | Moulding 71/02...T-108
$60 set up
add $20 for dado Type: bbrdm |
| 1111 |  | 6 x 7/8 | dado for a rope or dentil mld
Moulding 66/06...T-106
$95 set up Type: crwnm |
| 1224 |  | 6 x 13/16 | Moulding 81/03...T-120
large beads
$50 set up Type: bbrdm |
| 1268 |  | 6 x 13/16 | Moulding 83/14...T-112
$95 set up Type: crwnm |
| 1295 |  | 6 x 1-11/16 | Moulding 86/01...T-
$60 set up Type: bbrdm |
| 1372 |  | 6 x 1 | Moulding 91/01...T-134
$60 set up Type: bbrdm |
| 1440 |  | 6 x 3/4 | Moulding 97/04...T-131
$60 set up Type: bbrdm |
| 1449 |  | 6 x 1-3/8 | Moulding 98/04...T-141
$95 set up Type: crwnm |
| 1639 |  | 6 x 13/16 | Moulding 113/01...T-159
$60 set up Type: bbrdm |
| 1783 |  | 6 x 15/16 | Moulding 124/05...T-188
$95 set up Type: crwnm |
| 1859 |  | 6 x 3/4 | Moulding 131/01...T-181
$60 set up Type: bbrdm |
| 1862 |  | 6 x 7/8 | Moulding 131/04...T-
$95 set up Type: crwnm |
| 1865 |  | 6 x 13/16 | Moulding 131/07...T-183
$95 set up Type: crwnm |
| 1926 |  | 6 x 3/4 | Moulding 136/01...T-172
$75 set up
add $20 for dado Type: bbrdm |
| 1987 |  | 6 x 1 | Moulding 139/14...T-173
$95 set up Type: crwnm |
| 1989 |  | 6 x 1-7/8 | Moulding 161/01...T-204
$60 set up Type: miscm |
| 2002 |  | 6+ x 1-1/4 | Moulding 162/01...T-?
$60 set up Type: bbrdm |
| 2025 |  | 6 x 1-3/8 | Moulding 152/01...T-196
$60 set up Type: bbrdm |
| 2047 |  | 6+ x 3/4 | Moulding 154/01...T-195
$60 set up Type: bbrdm |
| 2048 |  | 6 x 1 | Moulding 154/02...T-194
$50 set up Type: casin |
| 2062 |  | 6+ x 1-1/2 | Moulding 155/01...T-198
$60 set up Type: bbrdm |
| 2074 |  | 6 x 3/4 | Moulding 156/01...T-199
$60 set up
add $20 for dado Type: bbrdm |
| 2091 |  | 6+ x 3/4 | Moulding 157/01...T-206
$60 set up Type: bbrdm |
| 2092 |  | 6 x 1-1/2 | Moulding 157/02...T-201
$115 set up with dados
as shown
$75 set up with only top knives Type: casin |
| 2129 |  | 6 x 1-7/8 | Moulding 160/01...T-204
$60 set up Type: miscm |
| 0436 |  | 6-1/8 x 1-1/8 | Moulding 149/12...T-27
$100 set up
Type: crwnm |
| 0613 |  | 6-1/8 x 1-11/16 | this is the top portion of a large two-piece crown...see CRWNM0612 for bottom piece.
Moulding 38/06...T-47
$75 set up
Type: crwnm |
| 2012 |  | 6-1/8 x 1-3/16 | Moulding 162/11...T-207,27
$115 set up Type: crwnm |
| 2073 |  | 6-1/8 x 1-1/4 | Moulding 155/12...T-199
$95 set up Type: cvbdm |
| 2128 |  | 6-1/8 x 3/4 | Moulding 159/16...T-202
$95 set up Type: crwnm |
| 0578 |  | 6-3/16 x 1-1/8 | Moulding 36/09...T-53
$95 set up Type: crwnm |
| 0219 |  | 6-1/4 x 1-5/16 | Moulding 16/12...T-38
$125 set up
Add $.50 for having to run twice Type: cvbdm |
| 0607 |  | 6-1/4 x 1-1/8 | Moulding 144/11...T-
$120 set up because of a deep cut is twice run Type: crwnm |
| 0721 |  | 6-1/4 x 1-1/16 | Moulding 141/12...T-66
$95 set up Type: crwnm |
| 0787 |  | 6-1/4 x 7/8 | Moulding 144/12...T-73
$95 set up
price from 5/4 stock Type: crwnm |
| 0830 |  | 6-1/4 x 2-3/4 | Moulding 52/01...T-80
$110 set up Type: crndm |
| 0924 |  | 6-1/4 x 1-1/4 | Moulding 59/05...T-38
$125 set up, add .60 per foot to run twice. Type: cvbdm |
| 1438 |  | 6-1/4 x 3/4 | Moulding 97/02...T-140
$60 set up
add $20 for relief Type: bbrdm |
| 1563 |  | 6-1/4 x 1-1/8 | Moulding 106/11...T-152
$95 set up Type: crwnm |
| 1641 |  | 6-1/4 x 1 | Moulding 113/03...T-160
$60 set up Type: casin |
| 1829 |  | 6-1/4 x 7/8 | Moulding 128/10...T-191
$95 set up Type: crwnm |
| 1821 |  | 6-3/8 x 1-1/4 | Moulding 128/02...T-190
$110 set up Type: bbrdm |
| 1925 |  | 6-3/8 x 3/4 | Moulding 135/14...T-172
$95 set up Type: crwnm |
| 1417 |  | 6-1/2 x 1-1/4 | Moulding 94/05...T-142
$95 set up Type: cvbdm |
| 1520 |  | 6-1/2 x 13/16 | Moulding 103/02...T-146
$60 set up Type: bbrdm |
| 1539 |  | 6-1/2 x 3/4 | Moulding 104/12...T-146
$95 set up Type: crwnm |
| 1650 |  | 6-1/2 x 1-1/8 | Moulding 113/12...T-159
Symmetrical
$95 set up Type: crwnm |
| 1719 |  | 6-1/2 x 7/8 | Moulding 118/14...T-166
$95 set up Type: crwnm |
| 1830 |  | 6-1/2 x 1-1/8 | Moulding 128/11...T-188
$95 set up Type: crwnm |
| 1973 |  | 6-1/2 x 1-1/4 | Molding 138/11...T-
$95 set up Type: crwnm |
| 1743 |  | 6-5/8 x 13/16 | Moulding 120/07...T-169
$95 set up Type: crwnm |
| 0736 |  | 6-3/4 x 15/16 | Moulding 49/02...T-74
$75 set up Type: crwnm |
| 0740 |  | 6-3/4 x 1-1/4 | BVS Moulding 49/06...T-75
$95 set up Type: cvbdm |
| 1638 |  | 6-3/4 x 1-3/8 | Moulding 112/10...T-157
$95 set up Type: crwnm |
| 1668 |  | 6-3/4 x 9/16 | Moulding 115/01...T-163
$60 set up Type: bbrdm |
| 1679 |  | 6-3/4 x 3/4 | Moulding 116/01...T-162
$60 set up Type: bbrdm |
| 1775 |  | 6-3/4 x 1-1/8 | Moulding 123/05...T-189
$95 set up Type: crwnm |
| 1866 |  | 6-3/4 x 1-3/4 | Moulding 131/08...T-185
$125 set up
add .50 per foot to run 3 times Type: crwnm |
| 2001 |  | 6-3/4 x 3/4 | Moulding 161/13...T-206
$95 set up Type: crwnm |
| 0517 |  | 6-7/8 x 1-3/4 | Moulding 33/11...T-48
$120.00 set-up
add $.60 per foot for having to run it twice Type: crwnm |
| 0720 |  | 6-7/8 x 13/16 | dentil
Moulding 147/12...T-67
$95 set up
Type: crwnm |
| 1587 |  | 6-7/8 x 1-1/4 | Moulding 108/11...T-154
$95 set up Type: crwnm |
| 1705 |  | 6-7/8 x 3/4 | Moulding 117/11...T-165
$95 set up Type: crwnm |
| 1777 |  | 6-7/8 x 7/8 | Moulding 123/06...T-190
$95 set up Type: crwnm |
| 0091 |  | 7 x 5/8 | 7 " tear-dropped siding
Moulding 07/07...T-3
$75 set up Type: sidin |
| 0188 |  | 7 x 1-1/16 | note the bevel and curve on same piece
Moulding 15/01...T-14
$85 set up Type: sidin |
| 0706 |  | 7 x 1-1/2 | very large beaded moulding that can be put side by side for even larger beaded moulding
Moulding 144/07...T-59
$60 set up
symmetrical Type: miscm |
| 0765 |  | 7 x 2-1/2 | used for casting
Moulding 50/05...T-76
$75 set up Type: crndm |
| 0935 |  | 7 x 7/8 | Moulding 60/02...T-95
known as a beveled, dadoed siding
$75 set up Type: sidin |
| 1033 |  | 7 x 1-3/16 | Moulding 67/03...T-99
$95 set up Type: crwnm |
| 1280 |  | 7 x 1-5/8 | Moulding 84/11...T-117
$110 set up, add .50 to run twice Type: cvbdm |
| 1505 |  | 7 x 2-5/16 | Moulding 102/01...T-144
$125 set up as shown
add .50/lf to run twice
eliminate or adjust the dado on bottom changes setups
symmetrical Type: hrail |
| 1893 |  | 7 x 11/16 | Moulding 133/10...T-183
$95 set up Type: crwnm |
| 2137 |  | 7 x 1-9/16 | Moulding 160/09...T-205
$95 set up Type: crwnm |
| 1379 |  | 7-1/8 x 1 | Moulding 91/08...T-103
$65 set up Type: sidin |
| 0031 |  | 7-1/4 x 1-1/4 | Moulding 02/10...T-6
$110 set up Type: crwnm |
| 0036 |  | 7-1/4 x 1-1/4 | Moulding 02/05...T-4
$95 set up Type: crwnm |
| 0119 |  | 7-1/4 x 1-1/2 | Moulding 10/01...T-14
$60 set up Type: bbrdm |
| 0264 |  | 7-1/4 x 1-1/2 | mount on a 2 x 2 to a wall for hallway handrail. Changes in thickness or heights are easily customized Moulding 19/07...T-31,26,10
as shown...$125 set up
Type: hrail |
| 0896 |  | 7-1/4 x 3/4 | very large crown still coming from 4/4" stock
Moulding 57/02...T-86
$95 set up Type: crwnm |
| 1034 |  | 7-1/4 x 1-3/4 | Moulding 67/05...T-107
$95 set up Type: crwnm |
| 1269 |  | 7-1/4 x 1 | Moulding 84/01...T-113
$60 set up Type: bbrdm |
| 1406 |  | 7-1/4 x 7/8 | Moulding 93/04...T-130
$95 set up Type: crwnm |
| 1773 |  | 7-1/4 x 3/4 | Moulding 123/02...T-191
$60 set up Type: bbrdm |
| 1778 |  | 7-1/4 x 3/4 | Moulding 123/01...T-191
$60 set up Type: bbrdm |
| 1790 |  | 7-1/4 x 3/4 | Moulding 125/04...T-186
$95 set up Type: panlm |
| 1819 |  | 7-1/4 x 1-5/16 | Moulding 127/11...T-184
$95 set up Type: cvbdm |
| 1831 |  | 7-1/4 x 11/16 | Moulding 129/01...T-179
$60 set up Type: bbrdm |
| 1894 |  | 7-1/4 x 1-3/4 | Moulding 133/11...T-178
$95 set up Type: cvbdm |
| 0390 |  | 7-1/2 x 1-1/16 | Moulding 145/12...T-30
$110 set up
add $.60 per foot for having to run it twice Type: crwnm |
| 1030 |  | 7-1/2 x 1-1/4 | Moulding 67/01...T-97
$95 set up Type: crwnm |
| 1404 |  | 7-1/2 x 1-3/4 | Moulding 93/02...T-135
$110 set up, add .40 to run twice Type: cvbdm |
| 1422 |  | 7-1/2 x 3/4 | Moulding 95/02...T-135
$60 set up Type: bbrdm |
| 1742 |  | 7-1/2 x 1-3/4 | Moulding 120/06...T-168
$125 set up
add .40 per foot to run twice.
Symmetrical Type: cvbdm |
| 1796 |  | 7-1/2 x 1-1/8 | Moulding 125/10...T-182
$95 set up Type: crwnm |
| 1974 |  | 7-1/2 x 3/4 | Moulding 139/01...T-193
$85 set up Type: bbrdm |
| 0871 |  | 7-5/8 x 1-3/4 | Moulding 55/01...T-81
$50 set up
symmetrical Type: crndm |
| 1343 |  | 7-3/4 x 1-3/8 | Moulding 89/01...T-129
$50 set up Type: miscm |
| 1744 |  | 7-3/4 x 1-1/2 | Moulding 120/08...T-169
$95 set up Type: crwnm |
| 1757 |  | 7-3/4 x 1-3/8 | Moulding 121/13...T-168
$95 set up Type: crwnm |
| 0299 |  | 7-7/8 x 13/16 | Moulding 21/07...T-35
$95 set up Type: crwnm |
| 1425 |  | 7-7/8 x 2-1/4 | Moulding 95/05...T-111
$75 set up
large wall cap can be any size with the angles on top being constant. Symmetrical Type: hrail |
| 1629 |  | 7-7/8 x 13/16 | Moulding 112/01...T-158
$80 set up as shown, $60 w/out relief Type: bbrdm |
| 0895 |  | 8 x 1-1/4 | symmetrical large cove
Moulding 57/01...T-83
$95 set up Type: cvbdm |
| 1032 |  | 8 x 7/8 | Moulding 67/04...T-107
$95 set up Type: crwnm |
| 1421 |  | 8 x 3/4 | Moulding 95/01...T-105
$60 set up Type: bbrdm |
| 1437 |  | 8 x 3/4 | Moulding 97/01...T-140
$60 set up Type: bbrdm |
| 1506 |  | 8 x 1-1/2 | Moulding 102/02...T-122
$80 set up
dado can vary
symmetrical Type: hrail |
| 1785 |  | 8 x 1 | Moulding 124/07...T-175
$95 set up
Type: crwnm |
| 0035 |  | 8-3/8 x 1-3/4 | Moulding 02/06...T-4
$140 set-up Type: crwnm |
| 0206 |  | 8-1/2 x 1-3/4 | rope or dentil molds can be added to flat spot. We have both in house.
mldg 15/08...T-12
$110 set up Type: crwnm |
| 1519 |  | 8-1/2 x 3/4 | Moulding 103/01...T-147
$60 set up Type: bbrdm |
| 1413 |  | 8-7/8 x 1-3/4 | Moulding 94/01...T-121
$110 set up, add .40 to run twice Type: cvbdm |
| 2099 |  | 8-7/8 x 13/16 | Moulding 157/09...T-200
$120 set up Type: crwnm |
| 1820 |  | 9 x 11/16 | Moulding 128/01...T-191
$60 set up Type: bbrdm |
| 1786 |  | 9-1/8 x 1-1/8 | Moulding 124/08...T-176
$95 set up Type: crwnm |
| 2100 |  | 9-1/4 x 1 | Moulding 158/01...T-203
Plinth block
$60 set up Type: miscm |
| 1776 |  | 9-3/8 x 1-5/8 | Moulding 123/07...T-187
$110 set up Type: crwnm |
Our on-site millwork shop is ready to cut to your specifications. Turn around is 1-2 days. Contact us online or call us at (713) 686-6176.
